Send Data on ThingSpeak cloud using Arduino and esp8266 wifi module

Send data on thingSpeak using Arduino and esp8266
link-arduino.esp8266...
#Arduino#arduinoproject#adruinouno#arduinofun#arduinofun#arduinomega#esp#esp8266#wifimodule#espwifimodule#iot#arduino#Thingspeak#cloud#thingspeakcloud#lm35#esp8266andlm35#arduinoandesp8266#arduinoandesp#arduinoproject#iotproject#thingspeakproject#cratechannelonthingspeak#
arduinotutorial#arduinoprogramming#thingspeakesp8266#thingspeaktutorial#thingspeakiotproject#thingspeakarduino#thingspeakarduinoesp8266#espandarduino#esp8266andarduino#arduinoand esp8266

[@thecreativetechart4536]

have you told that how these at commands are working so perfectly.... in maximum videos i am finding that no one is telling about the firmware and factory reset of the esp8266.. after resetting it only we will get the perfect output

[@viktor7425]

Hello, I did exactly the same as you only on the mega board, but when I type the AT command on the serial monitor nothing happens, I get no response.
I can use your help or just an opinion on why it wont work, thanks.

[@blackglove9779]

SAME THING I FACED WITH ARDUINO UNO

[@3dgiftz]

Thnaks a lot sir. very useful. Almost I have completed my project

[@josephdaquila2479]

If I don't want to use ThingsSpeak can I just write get and post commands?

[@gihansenanayake2416]

Thank you very much Amith for the video, I learnt a lot from this, it's a great video!

[@TechTooB2]

thank you so much

[@nandhinijagadeesan3835]

Can i connect Arduino mega with NodeMCU esp8266 and then connect to thingspeak to visualize sensor data?

[@surya2557]

U did?

[@nagasrihith608]

Very informative video, thanks and keep up the good work 🙌.

[@TechTooB2]

Thank you so much❤ it means a lot

[@Ri2singh]

Can you make a video to explain more about things speak cloud interface and how to use it from basic

[@TechTooB2]

Well sure

[@jackofalltrades2673]

hi sir
next month is my project presentation. i am doing project on IOT based health monitoring. showing spo2 in thinkspeak with the help of esp8266 and max30102. please make a video on that

[@jamessalvador8075]

Awesome tutorial, is there a way to send the data to google sheets instead of thingspeak?

[@ikeben9]

I'm thinking of using the read API of thinkspeak to send the data to Google sheets

[@ellieelenor156]

Hello, I really enjoyed your video! Could I please have the code to look at?

[@saitharun2588]

Thanks for the great video. Keep doing amazing stuff.

[@TechTooB2]

Thank you so much it means a lot❤😘

[@sabastianondieki-o7v]

hello,which software did you use to design your circuit?

[@laus-thecurious4120]

tinkercad most probably , ss is there
and now tinkercad does not support esp8266

[@SaurabhYadav-yb6mz]

Sir ....on going to new and then uploading the code on arduino uno ....there is showing an error

[@TechTooB2]

You can mail us on [e-mail] for any query

[@suryatilak7741]

Create A Circuit To Display A Message Internet Is Connected And Then When The Device Is
Connected To Thingspeak And Sending Data Successfully To It, Display All This In LCD
Display!!!plzz do this

[@TechTooB2]

If you want a make a project you can send the details on [e-mail]

[@baocao6049]

Thanks for the great video. Can you share the Arduino code?

[@luistimana2393]

Thanks. Can you share the Arduino code?

[@abhikchanda6222]

You must disconnect the tx and rx pin and upload the code after uploading the code to Uno connect rst of Uno to gnd and reconnect the tx and rx pin then only you can use AT command

[@PradeepSingh-pp1nj]

brother m done with uploading but cannot use AT commands can u help m using blynk tomorrow is my final capstone viva plz

[@SKMINSARR]

this comment save my semester

[@nurashikinahmad4933]

Can i use arduino Mega using this step ?

[@aisyamaulidyarulianti]

halo, can i get this code program?

[@khyimful]

Can u show the wire connections in the wifi module?

[@abheshekmaurya7736]

Wowwww bhaiya kaise kiyaaa 😮🙀🙀🙀

[@prashanthakm1160]

Sir please share code link

[@santhoskumar2592]

Sir i am using arduino nano but the light is not blinking what to do

[@TechTooB2]

Nano 3.3v output is not enough for esp8266 use a voltage regulator go give power to esp8266 or try with 5v but make sure that you don't keep ESP ON for long time.

[@santhoskumar2592]

@@TechTooB2 thank you sir

[@santhoskumar2592]

@@TechTooB2 sir it is not working for me kindly help me sir i am working on my mini project, how can i contact you

[@TechTooB2]

@@santhoskumar2592 mail me on [e-mail]

[@vihanvithanage5463]

How can i find the arduino code?

[@TechTooB2]

For code and library you can mail us on [e-mail]

[@arbaazimtiyaz]

Did you get the code mate?

[@edzellegaspi6117]

Hi! Can I have the code for this?

[@chatgpt-learneverything]

Can you share the code???

[@splendor10]

Thanks dear friend

[@yuvrajghatekari3916]

Hello sir please give me this Arduino code

[@mrpankhan7171]

Can i get code?

[@mostafahasan9940]

code?

[@nihalsabri3071]

Thank You

[@karlramboz5273]

What a ripoff, don't watch this deceptive video.

[@alexjames6747]

Do your videos in your native language,

[@MM-vr4lp]

can u share the code?

[@TechTooB2]

Mail us on [e-mail]

[@arbaazimtiyaz]

Did you get it?

[@MM-vr4lp]

@@arbaazimtiyaz no