Bring back your commentary! It's good hearing you explain what you're doing and how you feel it went. Great videos mate. Thanks a lot. Going to look so good when all done.
Hey Thanks for the compliment The next will be the side fairings and planning to build a carbon petrol tank. That will be something different for sure.🛠🤟
ha kesz leszek az udvarral, meg meg par fontos teendovel, tuti nekiallok vmi projektnek! Talan nem az 1000sx also spoilerevel kene kezdeni...😂😂😂 nagyon jo nezni, ahogy dolgozol. A dukis videoid sokszor lattam.
So, 2x 210g, a layer 450, then another 210? That's ... sturdy ^^ Anyway, great job. I like your methodical approach and attention to detail. Have you tried Easy Composite's resin-richer surface prepregs? Those might help with the pinhole issues you seem to have despite the good prep work.
Hey Thanks for the compliment!🛠🤟 Yeah I could of use a layer less in the build but I just wanted to make sure it will be sturdy as hell. I'll be trying out the out of autoclave prepreg very soon. I just still have too much of the other stuff. 😅
@@zrcarbon9937 You should contact their customer service first and give them the rough specs of your equipment, max vacuum and temp capabilities etc ... in theory the ec120 should be the best choice for hobbyists, but I've seen many ppl claim that the 160 autoclave prepreg cures with fewer pinholes even at the lower temps/pressures of their diy curing ovens. So maybe they know what's up with that and what to look out for. My only suspect based on your footage would be a perhaps too liberal application of the heat gun. The areas you use the most heat on to massage the overlaps into place and the spots with the most pinholes appear to be roughly the same. Happy laminating, and stay safe. (I wrecked enough bikes to know how tricky the latter can be^^)
really like this. Im very tempted to get the carbon fairing a rear cowling for my bike. so this carbon has the hardener already in it? just heat to activate?
Hello, what are the names of the pieces of carbon fiber you use and where can you buy them? I'm sorry for any spelling mistakes, but I'm writing with Google translator.
Bring back your commentary! It's good hearing you explain what you're doing and how you feel it went.
Great videos mate. Thanks a lot.
Going to look so good when all done.
He does have captions where he explains it too.
Thanks so much!
I will bring back the commentary 🏍️🛠️🤘
The fitment looks out of this world. I havet spent 3000$ on carbon still not 100% in fitment. Great job!
Yeah the fitment is perfect. 👌
All it takes is the attention to details.
Thanks for watching 🛠️🤘
Well done, excellent prepreg work!
Thanks for the compliment! 🛠️🤘
I think you should make the back cover of the mirrors, as always nice video
Hey
Thanks for the idea! I was planing to build something like a winglet to replace the mirrors. Like the Kawa H2R has.🛠🤟
Looks amazing man, perfect fitment and surface!!
Thanks so much! 🛠️🤘
So satisfying! Excellent work
Thanks so much for the compliment! 🛠️🤘
Looks awesome!
Thanks! 🛠🤟
Awesome job!!!!
Thank you! 🛠️🤘
Fantastic! Greetings from South Africa!
Thanks so much! I appreciate that you watching 🛠️🤘
Magnifique 😊
Thanks so much! I appreciate you're watching 🛠🤟
The quality of these videos are top notch man.
Thanks so much for the compliment! 🏍️🛠️🤘
Sick job!
Thanks so much!🛠🤟
Wow, that looks so cool man! What are you planning to build for your next video?
Hey
Thanks for the compliment
The next will be the side fairings and planning to build a carbon petrol tank. That will be something different for sure.🛠🤟
ha kesz leszek az udvarral, meg meg par fontos teendovel, tuti nekiallok vmi projektnek! Talan nem az 1000sx also spoilerevel kene kezdeni...😂😂😂 nagyon jo nezni, ahogy dolgozol. A dukis videoid sokszor lattam.
So, 2x 210g, a layer 450, then another 210?
That's ... sturdy ^^
Anyway, great job. I like your methodical approach and attention to detail.
Have you tried Easy Composite's resin-richer surface prepregs? Those might help with the pinhole issues you seem to have despite the good prep work.
Hey
Thanks for the compliment!🛠🤟
Yeah I could of use a layer less in the build but I just wanted to make sure it will be sturdy as hell.
I'll be trying out the out of autoclave prepreg very soon.
I just still have too much of the other stuff. 😅
@@zrcarbon9937 You should contact their customer service first and give them the rough specs of your equipment, max vacuum and temp capabilities etc ... in theory the ec120 should be the best choice for hobbyists, but I've seen many ppl claim that the 160 autoclave prepreg cures with fewer pinholes even at the lower temps/pressures of their diy curing ovens. So maybe they know what's up with that and what to look out for.
My only suspect based on your footage would be a perhaps too liberal application of the heat gun. The areas you use the most heat on to massage the overlaps into place and the spots with the most pinholes appear to be roughly the same.
Happy laminating, and stay safe. (I wrecked enough bikes to know how tricky the latter can be^^)
that one little blemish on the corner, you think was from bridging of your materials over the corner of your mold surface?
really like this. Im very tempted to get the carbon fairing a rear cowling for my bike. so this carbon has the hardener already in it? just heat to activate?
Awesome, good work 😎
Thank you! Cheers!
will you do the final cost breakdown? after build completion . or can you make a video about how much it costs to make carbonfiber parts per kg .
Yes sure
I’ll do that
Thanks for the idea 🤘🛠️
Great job! Did you CAD design those 3d printed brackets using measurements from a digital caliper? thank you
This is a good question! I’m curious if these are made on cad by hand or found online!
Amazing part though, top notch
Hey
Yes I made the brackets by hand in fusion 360 🛠️🤘
What type of that plastic that u shoot use a heater gun before vacuum cure..?
How did you make the mounting? Is it 3d printed?
Amazing work! Did it really pop out of the mold as easy as it looked?
Thanks you!
Yes, I was sooo happy with that. But I knew it won't be a problem because the pattern was popped out really easy.🛠🤟
In the video, white plastic was attached. Can you tell what material it is?
Hey
That board called Fluted Signboard. You can see me use it in my other videos🛠🤟
@@zrcarbon9937 Friend, other than that, what are the white parts at 19:23 made of? Did you actually 3D print it yourself? What is the material? PLA?
Très bien fait bravo pour le travail
Thank you so much 🏍️🛠️🤘
Another great video, is commentary coming back.
Hey
Thanks for the compliment. Yes I would like to have my next video with commentary🛠🤟
how your made white part for connect head light can you let me know? thank :)
Hai.. saya ingin melihat cara membuat breket menggunakan 3 d printer di konten selanjutnya❤
Круто !!
are the tabs 3d printed?
Hey
Yes they are.🛠🤟
Are you use which flament? Pla, petg, abs
For the prototype pla. For the production part carbon fiber.
Hello, what are the names of the pieces of carbon fiber you use and where can you buy them? I'm sorry for any spelling mistakes, but I'm writing with Google translator.
Do you sell carbon parts?
Hey
Yes I do! Are you interested?