Please help! I got a Subaru Ascent that was rear ended. Still has a bit of damage to where the blind spot bracket sits. I get the code for misalignment of the right radar. I have no idea how to do the measurements and from.where to start. Also, what tools will I need to get the radar alignment done. Is the corner reflector needed if so what that does or help with the alignment? Please explain to me as much information as you can. thanks!
Hola. Fíjate que en mi Scanner Maxicom mk808 le di calibrar a mis sensores traseros y me dio error y en el tablero me salía que no estaba configurado y que tenía error. Entonces al ir en camino me lleve el Scanner conectado y me paré a medio camino y le di RECALIBRAR y listo. Se me solucionó
@@tairot3112 Hola. Fíjate que en mi Scanner Maxicom mk808 le di calibrar a mis sensores traseros y me dio error y en el tablero me salía que no estaba configurado y que tenía error. Entonces al ir en camino me lleve el Scanner conectado y me paré a medio camino y le di RECALIBRAR y listo. Se me solucionó
are you ensuring the wheel alignment is well with in spec? the angle is not supposed to be pulled in relative with wheel angle but off the perfect center line of the vehicle. so if rear toe is off by even 2 degrees, your bsm angle is also going to be reading incorrectly
Yes you are correct all vehicles are put through an alignment check before we measure and align the blind spots,in general all ADAS alignments are performed after a four wheel alignment.
Yes it's approximately the same height as the blind spot sensor depending on the year make and model vehicle service manuals specifies a specific height in millimeters for each vehicle
hi, it takes about two hours. It requires to remove the bumper, set up and measure depending on the angles you might need extra bodywork to realign it. The cost varies depending on the amount of work needs to be done anywhere from US$300-US$1100, We are located in Cape Coral Florida. However, we are not a retail shop. We supply our services for the Collision and automotive industry
hope one day you will give us a toyota cruise control radar calibration. look fordward seeing you
Hey Jack, accurate Job ! Is the alignment rig self made? Or where did you buy it?
The state of the art tools are available online,
www.adasaiming.com
Please help! I got a Subaru Ascent that was rear ended. Still has a bit of damage to where the blind spot bracket sits. I get the code for misalignment of the right radar. I have no idea how to do the measurements and from.where to start. Also, what tools will I need to get the radar alignment done. Is the corner reflector needed if so what that does or help with the alignment?
Please explain to me as much information as you can.
thanks!
Hi and thank you for your help
Want to ask if this angle is the same for all toyota models as i have this issue in prius
Hi, all toyota vehicles are 90° vertical, however, horizontal some Toyotas are 50° and some Toyotas are 20°,
Yo lo que e hice fue pararme a la par de los carros y le di recalibrar y ya me funciono. Tengo un Scanner Maxicom mk808
Hola me puedes ayudar con un poco más de información sobre eso
Hola. Fíjate que en mi Scanner Maxicom mk808 le di calibrar a mis sensores traseros y me dio error y en el tablero me salía que no estaba configurado y que tenía error. Entonces al ir en camino me lleve el Scanner conectado y me paré a medio camino y le di RECALIBRAR y listo. Se me solucionó
@@tairot3112 Hola. Fíjate que en mi Scanner Maxicom mk808 le di calibrar a mis sensores traseros y me dio error y en el tablero me salía que no estaba configurado y que tenía error. Entonces al ir en camino me lleve el Scanner conectado y me paré a medio camino y le di RECALIBRAR y listo. Se me solucionó
are you ensuring the wheel alignment is well with in spec? the angle is not supposed to be pulled in relative with wheel angle but off the perfect center line of the vehicle. so if rear toe is off by even 2 degrees, your bsm angle is also going to be reading incorrectly
Yes you are correct all vehicles are put through an alignment check before we measure and align the blind spots,in general all ADAS alignments are performed after a four wheel alignment.
Check out adasaiming.com we offer a blind spot measuring alignment tool using the center line.
What is cost calibration
Hello, at what height did you place the triangle? The same height as the BSM module?
Yes it's approximately the same height as the blind spot sensor depending on the year make and model vehicle service manuals specifies a specific height in millimeters for each vehicle
How much does it cost to fix I have the same problem and want to fix it
Where did you find the spec of 50 degrees? I don't see any mention of it in service info..
I found the spec
it's under the collision repair Blindspot specs
I have 2021 highlander same problem I need contact information
Which state are😊 you located
Where can i find this tool
Hi , there are several version of this tool for sale at
adasaiming.com
I have 2021 highlander problem I need your contact information
Hi , you can contact me there is a link to my email on there "about"
@@adasaimingbyjackshort2123 how much does it cost and how long does it take
hi, it takes about two hours. It requires to remove the bumper, set up and measure depending on the angles you might need extra bodywork to realign it.
The cost varies depending on the amount of work needs to be done anywhere from US$300-US$1100,
We are located in Cape Coral Florida. However, we are not a retail shop. We supply our services for the Collision and automotive industry