I did that replacement with a cheap import carburetor. The thing was, the idle mixture ended up on the bottom where it was very hard to adjust. I took the thing out again, at least once, to back it off (add fuel) a couple of turns to make it idle ok. I also had to drill out where one of the other cables connected (I forget which). But now everything seems fine.
I bought a new AC 300 the last year they made them.What a great machine,super low could out pull machines with bigger motors,sorry i sold it ,was like new when i sold it first person that seen it bought it
Interesting, up to a point... perhaps you can add a link to the part supplier, or a better description of the carb (make, model) maybe update on the jet size etc) + ALWAYS start the vehicle to show off your handiwork.....
Be warned When you remove the carburetor, your head is exposed. It is very easy to drop a screw or something down into the engine. My advice is make sure You place a towel or a rag. In that hole. If you were to accidentally drop a screw down there, you're in a world of hurt.
I did that replacement with a cheap import carburetor. The thing was, the idle mixture ended up on the bottom where it was very hard to adjust. I took the thing out again, at least once, to back it off (add fuel) a couple of turns to make it idle ok. I also had to drill out where one of the other cables connected (I forget which). But now everything seems fine.
I'm about to do a carb change on the same exact 4 wheeler. Found this video very helpful 👍 thank you
I bought a new AC 300 the last year they made them.What a great machine,super low could out pull machines with bigger motors,sorry i sold it ,was like new when i sold it first person that seen it bought it
Just did an install!!!!!!! 43.00 carb works great.
Interesting, up to a point... perhaps you can add a link to the part supplier, or a better description of the carb (make, model) maybe update on the jet size etc) + ALWAYS start the vehicle to show off your handiwork.....
Cody from Longleaf Outdoors, just subscribed 🤙
Thanks!
Keep the videos going!! Find a group on Facebook and a forum on the internet and share this video on them
You should show a video of how it runs afterwards
Good vidio keep them coming
Thanks for sharing!
Nice bike, I got the same one 👍🏼
Having a heck of a time trying to get the new carb to go back in with the two boots. Seems cramped up.
Why did you choose to replace rather than rebuild? I can’t think of a reason not to rebuild.
The OEM carb is almost $800!
Just a new OEM float is over $80 (not including the needle and seat)!
eBay replacement carb is $46
GOOD VIDEO THANK YOU
What was the black hose on the carb for? Where does it connect?
Be warned When you remove the carburetor, your head is exposed. It is very easy to drop a screw or something down into the engine. My advice is make sure You place a towel or a rag. In that hole. If you were to accidentally drop a screw down there, you're in a world of hurt.
Are the Amazon carbs any good
Can’t even get it to try to start
Good fire, great compression and value adjustment ok
Any ideas ???
I need a video on wiring the starter on that Sam 4 wheeler. Can you do that?
Do you need to adjust any screws on the carburetor?
Yes you will have to. Set the fuel air mix screw about 3.5turns out
Reason for not just doing a carburetor rebuild??
Mine came without a carb
I need that carburetor. Where can I buy it?
Thanks will remove carb now
I've got a Linhai 300 my throttle lever is stuck,any suggestions why? R how can I fix the problem?
So it seems like getting parts for this atv is hard!
Nothing worse then watching the video and they don't even start the bike😤😡🤬
Is there a trick to taking off the fuel tank?
My Brand new carburetor spits out gas to the air filter anyone know the problem.
Can you send me a link for the part you bought I can’t find one that has a choke
New Carburetor for Arctic Cat 300 1998 1999 2000 2x4 4x4 300 Arctic Cat Carb. Put this in and thats the carb on ebay.
@@phitness2429 did you get carb? I have a 2001 400 artic cat what was your cost? Where? And did it work for you?
You need to edit your videos. Nobody wants to watch you unscrew every single bolt and nut.