Hi! Thanks for the video. We are the "Clarke" dealers and I will allow a few comments on the video 0:49 - Good idea to spread the tool out on cardboard and not on a dirty concrete floor. Dirt and sand will get on the tool and engine parts and filters. 2:26 - I recommend working with oil and fuel in gloves. These are liquids that are harmful to the skin and the skin will be sore after dirty oil. 2:50 - You have very much spilled dirty oil on clean foundations, this is bad practice and it is impossible to wipe it off to make the concrete clean and white again. Put cardboard and lots of rags underneath. 4:14 - You need to cover the oil filter base to keep dirty water out when you remove the water filter. 4:53 - You tightened the fuel filters with the tool about 2 turns after touching the rubber filter ring to the base. Do not use the tool to tighten the filter. The filter only needs to be hand tightened 3/4 turn. 6:51 You did not pump oil with the starter (into the turbo and oil filters) before starting the engine. After the start there was oil starvation of the turbo and bearing. 7:05 Oil pressure (cold oil) is 0 and you didn't stop the engine and find the cause Good Luck!
is that diesel engine get jammed while its not run for a long period? what are the precautions to do before restarting an engine. battery is replaced and verified the connections and selfstart motor.
Guys the Clarke coolant capacity table "18.5 liters" is it talking about the entire loop+expansion tank or it refers just to the tank capacity? Thanks in advance
Hi!
Thanks for the video. We are the "Clarke" dealers and I will allow a few comments on the video
0:49 - Good idea to spread the tool out on cardboard and not on a dirty concrete floor. Dirt and sand will get on the tool and engine parts and filters.
2:26 - I recommend working with oil and fuel in gloves. These are liquids that are harmful to the skin and the skin will be sore after dirty oil.
2:50 - You have very much spilled dirty oil on clean foundations, this is bad practice and it is impossible to wipe it off to make the concrete clean and white again. Put cardboard and lots of rags underneath.
4:14 - You need to cover the oil filter base to keep dirty water out when you remove the water filter.
4:53 - You tightened the fuel filters with the tool about 2 turns after touching the rubber filter ring to the base. Do not use the tool to tighten the filter. The filter only needs to be hand tightened 3/4 turn.
6:51 You did not pump oil with the starter (into the turbo and oil filters) before starting the engine. After the start there was oil starvation of the turbo and bearing.
7:05 Oil pressure (cold oil) is 0 and you didn't stop the engine and find the cause
Good Luck!
well appreciated thank you
New subscriber watching from Al Khafji Saudi Arabia
Sir what meaning engin oil pressure lo .what solution sir pls for fire d s l engine
like
Thanks for sharing. Could you share the engine turbo or exhaust normal temperature?
Sir fire engine m coolent kon sa dala jata h
Hello sir,in deisel engine pump head controller is showing water temp sensor open ,what is sulotion and where it located? Eaton brand system
In 1250 GPM fire driver pump engine ,how many liters or gallons need to change oil sir thank you...
Sir .oil pressure loss what solution pls.(fire desel engin)
Hey plz can share engine oil capacity
is that diesel engine get jammed while its not run for a long period? what are the precautions to do before restarting an engine. battery is replaced and verified the connections and selfstart motor.
Its possible when not run for long time ,engine servicing as per the video has to be carried out check the batteries acid if applicable..then test run
Guys the Clarke coolant capacity table "18.5 liters" is it talking about the entire loop+expansion tank or it refers just to the tank capacity? Thanks in advance
referring to all cos the residual tank provided are always small in size
336 KW Engine per hour disel rate
The same engine oil capacity liters.....
20 liters but u can check with the dip stick whiles filling it so it does not get over
@@engineersguide4249thank you sir,,,and what good brand for change oil and also coolant