maganda sir ung mga content video mo. god bless po. my request po ako sna mag tutorial po kyo kung paano mag bleed ng coolant ng ranger 2.2 engine.salamat po.
madali lang naman sir kung mapapansin mo ung maliit na pipe sa upper tank hugutin mo lang un habang sinasalinan mo ng tubig once na umapaw dun ok na un ibalik mo na
Good job na nmn.. sir pano pag naopen na ung cover nang timing chain tas hindi naka timing sa diamond mark , pano pon ang ikot clockwise hanggang tatapat sa diamondd mark at yun na yung timing? Ty in advance sir mabuhay
Are the head and cam holders inter changeable or does it come as a pair that was casted and machined/bored to fit camshaft? I changed cam holder and now the cams are very hard to turn after finger tighting the cam holder/frame?
Ok Po Wala Po KC aqng nadidinig sa ibabaw sa gilid gawing exhausted manifold gitna NG makina Po eh,, pag Po ba irereface dapat tlga kasama ung engine block? Ung sinamahan q Po KC ndi ganun ginawa eh Kaya Duda Po aq baka meron pang ibang Tama,
@@blackmammoth3022 kahit di i repace ung block di naman kailangan reface yan suspect ko dyan piston or mga bearing ask lang anung size ng head gasket ginamit nyo
Ayos kabayan galing Ng tutorial mo.god bless kabayan.
Good job pare
Very informarive content good job keep sharing....
Thank you, I will
Nice one sir nag susubay bay Ako sa mga upload mo. Paano timing. Nang pressure pump
meron naman timing mark sir
Good jor sir
Good job po
Thank you! 😊
Good job sir
keep sharing
maganda sir ung mga content video mo. god bless po. my request po ako sna mag tutorial po kyo kung paano mag bleed ng coolant ng ranger 2.2 engine.salamat po.
madali lang naman sir kung mapapansin mo ung maliit na pipe sa upper tank hugutin mo lang un habang sinasalinan mo ng tubig once na umapaw dun ok na un ibalik mo na
nice
good job Sir, Godbless!
Nice good job sir..
Keep watching
Good job na nmn.. sir pano pag naopen na ung cover nang timing chain tas hindi naka timing sa diamond mark , pano pon ang ikot clockwise hanggang tatapat sa diamondd mark at yun na yung timing? Ty in advance sir mabuhay
ok lang di naka timing yan kc sa una lang naman na set ang timing once na umikot na mawawala sa tapat ung marking nyan
Can u plz turn on English subtitles
Panu po timing settings ng high pressure pump ng ford ranger 2.2
Are the head and cam holders inter changeable or does it come as a pair that was casted and machined/bored to fit camshaft? I changed cam holder and now the cams are very hard to turn after finger tighting the cam holder/frame?
if you chane cam shaft cap with the local one not fit to original camshaft make sure use original camshaft cap
How to remove fotd ranger 2.2 cylinder head
Same torque parin bato sa ford ranger boss na 2.2
Ask lang idol lahat ba Ng high pressure pump may fuel pump sa tangke. Salamat Po always watching 💯🏆👏🥇
meron din unit na wala pump sir
@@themechanictvchannel pero pag pressure pump na Po ba Ang car need na Ng fuel pump?salamat po
@@superfoood4618 may naka built in na yan boss depende sa unit kung walang pump deaign nya yan
Idol ano ang firing order ng5cylinder at running mate
boss ask lang yung vacuum pump poba may timing? nakasama po yun sa exhaust cam diba?
wala timing yan sir
Can you do in English please
sorry my english is very poor boss
Bossing ask q lng Po Sana Anu mga dahilan NG lagatak ng 3.2? Galing overheat Po, pero n top overhoul nmn Po sya,
depende sir pweding piston depende sa ingay sir pa diagnose ng maigi
Ok Po Wala Po KC aqng nadidinig sa ibabaw sa gilid gawing exhausted manifold gitna NG makina Po eh,, pag Po ba irereface dapat tlga kasama ung engine block? Ung sinamahan q Po KC ndi ganun ginawa eh Kaya Duda Po aq baka meron pang ibang Tama,
@@blackmammoth3022 kahit di i repace ung block di naman kailangan reface yan suspect ko dyan piston or mga bearing ask lang anung size ng head gasket ginamit nyo
Binili lng Po kc NG ngppagawa un fomoco din nmn Po sya,
boss pwed magtanung😊
anu un sir
Saan location mo sir?
malaysia ako sir
Good job pare
thank you pare..
Keep sharing
Good job pare