Please, Please, make a video of setting up a node and adding a node to a group. I have 3 TBeam boards all already to go. I just can't get them to talk to each other. Thank and best wishes.
just soldered two tbeam boards for the first time and installed an 18650 and plugged it in. I have a blue light but the screen isn't coming on. I used ham radio crash course to reference which holes for the pins. any suggestions? battery is properly oriented and the antennas are on
Thanks for the video, my T-beam has been out of use for a while and I forgot which button does what! Couple of 868mhz (and one 433mhz) Heltec units on order; hope to relegate the T-beam to use as a repeater unit! Richard G8ITB.
You said every time pressing the middle button the radio is performing the equivalent of a heart beats to the rest of the net work is that correct if so changing screens is sending multiple heartbeat beats is that correct. I have to admit I’ve been power cycling the radios if I need to force a connection it would be good to confirm if it’s on every middle button press. Or is it a press and hold? VK1MIC
I bought the TTGO T-Beam V1.1 for EU865, installed the software (firmware-tbeam-EU865-0.7.10.bin) and tried to connect the device with the Android Meshtastic App via Bluetooth, but after typing 0000 or 1234 the devices don't pair and connection always fails. What is the reason for this? Or do I have to do something different? Thanks for your help!
Make sure you choose the correct firmware build: For the T-Beam 868MHz (EU) unit use: firmware-tbeam-EU865-0.9.1 (as of 26/7/2020) The app software I am using is 0.8.03 which fixes the Bluetooth re-pairing issue on older phones.
Hello sir, I’m student from Indonesia, I want to ask how to set the screen settings so that incoming and sent text messages can be seen, and also how to display them for each connected node? I really hope you can help and reply to my message. Thank you
Hi, at 3:21 you have connected the T-Beam to an external antenna: what impedance do you recommend for the coaxial cable? 50 or 75 ohms? Also, what adapter do you use?
For co-axial feeders the convention is that transmitting antennas are always 50Ω and receivers always 75Ω. Where you have a Transmitter/Receiver we use 50Ω. The physics is complex, but there is good reason for this.
Are you sure it's the same version? Be careful to select the correct version of firmware for your hardware, not the old V1's are no longer supported. Mine is later than this.
I have Meshtastic 1.3.26 and only the left button works to restart. I don't know what software you are using but your suggestions do not work on my two units. Its shocking and offensive as to the lack of support for beginners with this device.
It’s quite an old video now. I am planning a new video that is up to date with the latest version. I’m installing two new nodes in SE London and will include this information too.
@@michelephilipp9277 OK, which file did you choose to upload? You have to be extremely careful to choose the correct file for your particular board, region and frequency band. This is the mistake most people make.
Hello I have just received one of these boards (First one ever so total noob) I have connected it to arduino but nothing can be loaded on to it Comes up with fatal error When I google search it says boot loader was not engaged How do I do this Best wishes ☺️
G8YTZ Probably not What would you recommend There is very minimal information and tutorials on these boards on here And I will admit I am clutching at straws contacting you As I can’t seem to find anything to resolve this issue
I just had a revelation in this regard: 4 of my TTGO T3_V1.6 ESPs require /dev/ttyUSB0 as a com port. 4 others did not work, and a TTGO Meshtastic GPS LoRa ESP refused to communicate with the computer. Then I tried connecting via /dev/ttyAMAO. it appears that Lilygo switched from CP2102 serial chips to CH340s at some point. open up your IDE without the ESP plugged in, see what ports are available, then plug in the ESP. either /dev/ttyUSB0 or /dev/ttyAMAO will show up. use that port. anybody knows where the I2C port pins really are, speak up, please
Hi sir. I’m a student from Taiwan who really likes ur videos. I have a question. I’m wondering whether u know how to use it without a oled display. Please,reply to me as soon as u can.Thank you!
Oh ok. So the OLED display is a must-have item. I thought that maybe we could get the Bluetooth key or other information by using port monitor,but it seems that maybe the most efficient way is to get one OLED display. Thx for ur reply.
@@shihjiunlin4242 its not as practical, but you could use a computer or even an android with otg adapter to get the bluetooth pin from the serial console. The moment you try to connect to the device it prints the pin on the console
This video has helped a lot of people! Thanks for the great video. :)
Thanks for the video. Very helpful. Looking forward to the next one.
Please, Please, make a video of setting up a node and adding a node to a group. I have 3 TBeam boards all already to go. I just can't get them to talk to each other. Thank and best wishes.
Waiting for the next video about the software. Great content of a great project!
Many thanks, the instruction video is WiP!
just soldered two tbeam boards for the first time and installed an 18650 and plugged it in. I have a blue light but the screen isn't coming on. I used ham radio crash course to reference which holes for the pins. any suggestions?
battery is properly oriented and the antennas are on
Thank you for the video
Double clicking the middle button will reset the bluetooth password to 12345678 which is great if your scren stops working.
Question, does the 18650 battery charge while the Beam is plugged via usb?
Yes it does, it acts as a float
@@G8YTZ Thanks !
Thanks for the video, my T-beam has been out of use for a while and I forgot which button does what! Couple of 868mhz (and one 433mhz) Heltec units on order; hope to relegate the T-beam to use as a repeater unit! Richard G8ITB.
Getting slicker by the minute
Thumbs up
You said every time pressing the middle button the radio is performing the equivalent of a heart beats to the rest of the net work is that correct if so changing screens is sending multiple heartbeat beats is that correct. I have to admit I’ve been power cycling the radios if I need to force a connection it would be good to confirm if it’s on every middle button press. Or is it a press and hold? VK1MIC
I reflashed my device and want to put this software back on. Is there a download for it?
Excellent video looking forward to the next one .
Thanks 👍
thanks.
Can I use this to get a moving node to trigger it to switch on a relay at 20meter distance signal
I bought the TTGO T-Beam V1.1 for EU865, installed the software (firmware-tbeam-EU865-0.7.10.bin) and tried to connect the device with the Android Meshtastic App via Bluetooth, but after typing 0000 or 1234 the devices don't pair and connection always fails. What is the reason for this? Or do I have to do something different? Thanks for your help!
Found it out by myself in the meantime after having connected an OLED display with the T-Beam. It is displaying a code for pairing the device. :-)
Make sure you choose the correct firmware build: For the T-Beam 868MHz (EU) unit use: firmware-tbeam-EU865-0.9.1 (as of 26/7/2020)
The app software I am using is 0.8.03 which fixes the Bluetooth re-pairing issue on older phones.
Hello sir, I’m student from Indonesia, I want to ask how to set the screen settings so that incoming and sent text messages can be seen, and also how to display them for each connected node? I really hope you can help and reply to my message. Thank you
What do you think of the stock antenna that comes with the Tbeam?
my oled not working and cant pair as cant see pair code, in consol it just returns gibberish so cant read from consol wtf shal i do?
Hi, at 3:21 you have connected the T-Beam to an external antenna: what impedance do you recommend for the coaxial cable? 50 or 75 ohms? Also, what adapter do you use?
For co-axial feeders the convention is that transmitting antennas are always 50Ω and receivers always 75Ω. Where you have a Transmitter/Receiver we use 50Ω. The physics is complex, but there is good reason for this.
@@G8YTZ thank you!!
I bought this model a few years back and only got around to trying it the other day and need to upgrade the firmware. I tried with no success.
Are you sure it's the same version? Be careful to select the correct version of firmware for your hardware, not the old V1's are no longer supported. Mine is later than this.
@@G8YTZ Success!
I have Meshtastic 1.3.26 and only the left button works to restart. I don't know what software you are using but your suggestions do not work on my two units.
Its shocking and offensive as to the lack of support for beginners with this device.
It’s quite an old video now. I am planning a new video that is up to date with the latest version. I’m installing two new nodes in SE London and will include this information too.
Help me please.. I have two t-beam but I'm not able to connect tem?
Hi Michelle, firstly, can I ask which model of t-beam you have, and what’s the file name that you’ve downloaded to flash them with?
TTGO T-beam V1. 1 esp 868/915 wifi... Oled... GPS neo - 6m
Firmware1.1.5 was the filename download github/meshtastiv
@@michelephilipp9277 OK, which file did you choose to upload? You have to be extremely careful to choose the correct file for your particular board, region and frequency band. This is the mistake most people make.
@@G8YTZ okay but I say it's the correct one... I have choose t-beam with 868... And I choose correctly 2 times the same
what battery should be used? with head or flat?
Flat
18650, Panasonic are the best.
Version ?
Hello
I have just received one of these boards
(First one ever so total noob)
I have connected it to arduino but nothing can be loaded on to it
Comes up with fatal error
When I google search it says boot loader was not engaged
How do I do this
Best wishes ☺️
Steve Tillotson Aure you’re using the correct software for the board you have?
G8YTZ
Probably not
What would you recommend
There is very minimal information and tutorials on these boards on here
And I will admit
I am clutching at straws contacting you
As I can’t seem to find anything to resolve this issue
What about double click?
Where can i update firmware?
I just had a revelation in this regard:
4 of my TTGO T3_V1.6 ESPs require /dev/ttyUSB0 as a com port. 4 others did not work, and a TTGO Meshtastic GPS LoRa ESP refused to communicate with the computer. Then I tried connecting via /dev/ttyAMAO. it appears that Lilygo switched from CP2102 serial chips to CH340s at some point.
open up your IDE without the ESP plugged in, see what ports are available, then plug in the ESP. either /dev/ttyUSB0 or /dev/ttyAMAO will show up. use that port.
anybody knows where the I2C port pins really are, speak up, please
Hi sir. I’m a student from Taiwan who really likes ur videos. I have a question. I’m wondering whether u know how to use it without a oled display. Please,reply to me as soon as u can.Thank you!
You need the OLED display I'm afraid, its a very cheap item and trying to do without would be far too painful.
Oh ok. So the OLED display is a must-have item. I thought that maybe we could get the Bluetooth key or other information by using port monitor,but it seems that maybe the most efficient way is to get one OLED display. Thx for ur reply.
@@shihjiunlin4242 its not as practical, but you could use a computer or even an android with otg adapter to get the bluetooth pin from the serial console.
The moment you try to connect to the device it prints the pin on the console