@abc_123_handle the issued was the rock could not be move forward and backward that the engine wild so I remove the injection pump cover to push my the slide used my finger.the second one was the injector is not good so I replaced or calibrated.thats it.thank you for the comments.please like and share....
Hello, I Have an L3E. Changed filters and oil. Bled the fuel system and now have a knocking which sounds like it coming from #1. If I crack the injector nut sound changes. Running rough and stalls when you try to move it. Its in CX7B excavator. Thanks
Welcome I bought a Kubota B1400, the problem with it is that the cold engine at idle runs very unevenly so that it can even go out, so I have to raise the speed immediately after firing so that it does not go out, after warming up the engine works quite steadily, which may be the reason for this ? pump or sprinklers? I will be grateful for your response. Greetings from 🇵🇱
hi i have almost the same problem with my d1350df , white smoke like crazy working for a while like 2 min and turn of and this doesn't end , never turn on on first try , please give advice.
Sir ano po dapat galawin jan...ganyan na ganyan po ang aking tractor po....gusto ko po sana lumakas kc ang hina po nya pag ginagamit kong pang araro....namamatay po kc sya kong ginagamit kong pang araro...pls po sana meron pa pong paraan para lumakas kahit konti lang
Blowby po ba sir kapag ka may usok na sa breather?bale inoverhaul n po nmin kse tatay ko lng din po ngaayos medyo malalim n valve seat manipis n ang valve
Hello po sir,,,magtanong nga po Kasi first time ko po nag overhaul ng D850 Kubota,,,ganito Kasi yan sir pagbukas ko po sa mga timing gear nya wala po sa timing kaya inulit ko,,,nilagay ko sya sa top dead center piston #1 at tsaka tinayming sa crankshaft,,, camshaft,, injection pump gear at idle gear,,,,so nung inikot ko sya Hanggang mapunta ulit sa top dead center piston #1 bakit nawala ulit sa timing kada ikot q ng flywheel malayo parin sya,,,,nka ilang ulit na ako nag timing pero ganun parin sir ,,,,,Sana po matulungan nyo ako,,,,salamat po
Kung naitiming mo n. ok n yan.kahit anong ikot mo nyn Hindi mo agad Makita n babalik sa timing iyn.bakaabutin k ng hundred times nyn bago mo maibalik ung timing mark
Hahah...nako sir maraming salamat po talaga sir hah,,,Sana palaguin pa ng Panginoon Ang RUclips channel mo pra maraming pang tao Ang matulungan mo,,, Godbless u po sir
Bos sana matulongan nyo po ako s problema ko s tractor ko li225 bos blowby. Nagpalit npo kmi ng piston, piston ring, valve quide, at valve seals. Bos bakit bos blowby pare at mausok ang tambutsok bluewish po ang usok. Backjob po tatlong beses na yung mikaniko laki nrin ng gastos ko bos sna bos matulungan nyo ako. Pa advice nman ako bos. Ano kya problema ng li225 tractor ko bos.
Check mo po alternator, pag vacuum type ang alternator eh yun ang dahilan bakit may preasure sa air breather o deep stick ng makina. Replace nyo nlng vacuum ng alternator
Sir,salamat po sa panunood.pkisaubscribe Naman po channel ko alin po b Ang tinatanong nyo n pagtiming?tune up po b?Kung tune up...pki pindot po Ang PLAYLIST sa sa cp mo kapag nanood k po sa channel ko,Makita mo po Kung paano mag tune up.salamat po
Good channel Sr. and your solutions are awesome !!!
Thank you for watching
What solution ? Please explain what the issue was and how they managed to repair it.
@abc_123_handle the issued was the rock could not be move forward and backward that the engine wild so I remove the injection pump cover to push my the slide used my finger.the second one was the injector is not good so I replaced or calibrated.thats it.thank you for the comments.please like and share....
Have a d905 very slow reaction to throttle change and can’t handle any load will shut down
Thanks you very much good working 👍👍👍🌹🌹🌹
Good job Sir 👍
Salamat sa panonood boss
Did someone check if push rods were bent, is that what you pulled them out for?
I have kubota b1750 and went the engine works about 2 hour the 3 point is not lifting up.
ruclips.net/video/ALrTmpeaW_g/видео.html
Please watch the above link. one of my video maybe your problem is the same on that video.
Very interisting thanks a lot sir
Thank you also for watching
Hello, I Have an L3E. Changed filters and oil. Bled the fuel system and now have a knocking which sounds like it coming from #1. If I crack the injector nut sound changes. Running rough and stalls when you try to move it. Its in CX7B excavator. Thanks
Also still seem to have air bubbles at the nut on #1. If you crack 2 and 3 it wants to stall but not when you crack 1?
Maybe nozzle tip from cylinder number one is not good. just try to calibrate
@@tractorsmarinemechanic what do you mean nozzle tip? Thanks
The nozzle tip at the end of injector is called nozzle.
@@tractorsmarinemechanic ok so remove the injector and inspect the part which is in the head? Thanks
Welcome I bought a Kubota B1400, the problem with it is that the cold engine at idle runs very unevenly so that it can even go out, so I have to raise the speed immediately after firing so that it does not go out, after warming up the engine works quite steadily, which may be the reason for this ? pump or sprinklers? I will be grateful for your response. Greetings from 🇵🇱
Kindly check the fuel filter.
@@tractorsmarinemechanic Thanks for the answer, I replaced the fuel and air filter right after I bought the tractor.
Точно такая история у меня тоже.
I do have the same. Fuel filter replaced. Did not help😢
Now I have replaced injectors. Starts perfectly now. Runs at idle perfect. Less smoke. I m happy😅
Thank you sir..😘❤️
Injektor not right or the fuel pump ? What was it now ?
Injector
@@tractorsmarinemechanic a thanks. You change them all and tractor run perfectly ?
hi i have almost the same problem with my d1350df , white smoke like crazy working for a while like 2 min and turn of and this doesn't end , never turn on on first try , please give advice.
Nozzle tip is stuck up or the plunger
@@tractorsmarinemechanic thank u very much will try see if it is ty.
Bad injector?
Yes ! Very interesting.
Dobra robota.
Sir ano po dapat galawin jan...ganyan na ganyan po ang aking tractor po....gusto ko po sana lumakas kc ang hina po nya pag ginagamit kong pang araro....namamatay po kc sya kong ginagamit kong pang araro...pls po sana meron pa pong paraan para lumakas kahit konti lang
May blowby n po b Ang engine mo?baka marumi n Ang air cleaner mo.linisin mo muna.abo po b model ng tractor mo?
Sir ano po ba pwde ikabit sa multicab na three cylinder diesel engine?salamat po
Para tipid sa diesel,Kubota engine sir Ang ikabit mo.
boss paano po maglagay ng balbola kasi natanggal k meron palang marka L2000 po boss tnx,,
Anong balbola po?sa cylinder po b?
Pag bo ba mataas ang idle san po pwede mag adjust?
Ano po Ang makina nyo or tractora nyo?
Paano po alisin sa makina ang water pump ng kubota d850
Bakit nyo po aalisin?sira po b or tangalin nyo ng tuluyan?
Boss anong dapat gawin kapag mahina na ang hatak ng makina d850 din medyo may kalumaan n nga lang gamit namin sa bangka?
Dependi sir...baka blowby n or plunger ay mahina n.patingin mo sa mekaniko dyn sir
Blowby po ba sir kapag ka may usok na sa breather?bale inoverhaul n po nmin kse tatay ko lng din po ngaayos medyo malalim n valve seat manipis n ang valve
Banging overhaul po b Yan or matagal n?kapag malakas n Ang usok sa breather ay blowby n po Yan.
May katagalan na po sir ng overhaulin namin.,ano po bang dapat gawin sir pag ka may usok na sa brether or blowby na?
Palit n ng ring.
Hello po sir,,,magtanong nga po Kasi first time ko po nag overhaul ng D850 Kubota,,,ganito Kasi yan sir pagbukas ko po sa mga timing gear nya wala po sa timing kaya inulit ko,,,nilagay ko sya sa top dead center piston #1 at tsaka tinayming sa crankshaft,,, camshaft,, injection pump gear at idle gear,,,,so nung inikot ko sya Hanggang mapunta ulit sa top dead center piston #1 bakit nawala ulit sa timing kada ikot q ng flywheel malayo parin sya,,,,nka ilang ulit na ako nag timing pero ganun parin sir ,,,,,Sana po matulungan nyo ako,,,,salamat po
Kung naitiming mo n. ok n yan.kahit anong ikot mo nyn Hindi mo agad Makita n babalik sa timing iyn.bakaabutin k ng hundred times nyn bago mo maibalik ung timing mark
Hahah...nako sir maraming salamat po talaga sir hah,,,Sana palaguin pa ng Panginoon Ang RUclips channel mo pra maraming pang tao Ang matulungan mo,,, Godbless u po sir
2003 Dodge Cummings clutch switch
If you could record a movie on how to remove seized injectors, we would be grateful.
I will do it just for you.just keep subscribed. thank you for watching
@@tractorsmarinemechanicThanks👍
Bos sana matulongan nyo po ako s problema ko s tractor ko li225 bos blowby. Nagpalit npo kmi ng piston, piston ring, valve quide, at valve seals. Bos bakit bos blowby pare at mausok ang tambutsok bluewish po ang usok. Backjob po tatlong beses na yung mikaniko laki nrin ng gastos ko bos sna bos matulungan nyo ako. Pa advice nman ako bos. Ano kya problema ng li225 tractor ko bos.
Tawag k po s #09502423351
@@tractorsmarinemechanic maraming salamat bos s pag accept ng tawag ko bos
Check mo po alternator, pag vacuum type eh don dumadaan ang preasure na lumalabas sa air breather ng makina
Check mo po alternator, pag vacuum type ang alternator eh yun ang dahilan bakit may preasure sa air breather o deep stick ng makina. Replace nyo nlng vacuum ng alternator
Oil looks a little like sludge... Might need some maintenance lol
Paano ang timing ng kobuta 3 cylinder
Sir,salamat po sa panunood.pkisaubscribe Naman po channel ko alin po b Ang tinatanong nyo n pagtiming?tune up po b?Kung tune up...pki pindot po Ang PLAYLIST sa sa cp mo kapag nanood k po sa channel ko,Makita mo po Kung paano mag tune up.salamat po
😊