CLUTCH TECH: Wet Dual Clutch Transmission (DQ250) Clutch Assembly Removal & Installation Guide
HTML-код
- Опубликовано: 30 сен 2024
- Australian Clutch Services stock a wide range of Dual Clutch Transmission clutch assemblies and specialised installation and removal tools. In this video, we show you the process for removing the old clutch assembly and the installation/setup procedure for the new clutch assembly. This is a VW DQ250 (02E) 6 spd style transmission and the procedure may change depending on the specific vehicle. For more information on the Australian Clutch Services DCT product range, please visit www.australianclutch.com.au
very well made instructions, helped a lot in replacing the clutch. thank you very much
Can i reuse the same shim into the new clutch pack or do i have to so the measurements
Thank you for sharing. This might be a silly question, but if my calculation is 2.15, and my nearest lock rings measure 2.1 and 2.2, is it best to lean towards the 2.1 with a looser fit, or 2.2 with a tighter fit along the shaft? Or do I get even more precise and surface grind a thicker lock ring down to 2.15?
I wish someone who cared about this car and had some more knowledge of it reviewed it. With the story this car has, I don’t feel he paid his respect where it was due.
As for the seating position, there is a handle on the left hand side of the driver seat that lowers it.
I love the VR6 and I hope to send mine to HPA some days as well. Mine is pretty much the same model with 67k and in brilliant black 😉
You make it look very simple. Still, I don’t think it’s something I’d try myself
While taking measurements using dial gauge shouldn't the T10303 clutch retaining tool be inside?
Hi,
This tool is only required to assist holding the clutch basket in place when installing the top cover so it shouldn't be in at that point.
If you have any further questions, please email our friendly sales team on sales@australianclutch.com.au
Thanks
Very detailed, thanks👍🏾
Hi.I just wanna ask after changing clutch.Should I adjust selector lever cable?thanksI
Hi,
Thank you for your comment. In this application there should be no requirement to adjust the cable.
Thanks
Would that 1.85mm constant value spec be the same number I would use for a 2016 Volkswagen Golf R with the DQ250? Thanks in advance!
can dct gearbox equipped in a car be replaced by AMT (Automated Manual Transmission) gearbox?
I can't wait for my new clutches to arrive!
Thanks for the great video!
What is cost to replace clutch pack on 2017 Golf Alltrack DQ250
Hi: thanks for the video!! what is the name of the pliers you use for installing the retaining rings? Thanks..
What does the clutch dowel exactly do? The one holding it up. Doesn’t look like it does much?
Rob
Do you lose any dsg fluid when doing this? Vw replaced my clutch pack and when I asked if there was any fluid loss they claimed no.
Hi Greg, thanks for your comment.
There is no fluid loss due to it being a fully sealed gearbox. The gearbox is removed from the vehicle and the clutch pack is replaced as per the video.
Yes and no. If your gearbox was pulled from a FWD, no it won't loose fluid because your axle shafts remain connected. But, if your gearbox was pulled from an AWD (Quattro), the transfer case is removed and fluid will spew out of the shaft hole. You can try taping it closed, which can hold the fluid in, but don't think you can wait for parts for several days or you will have fluid all over the floor. And, if laying it on it's side fluid will eventually leak out of the electrical connector.
Do you need to have that tool to hold it up or can you just have a friend hold it?
Hi,
You could just hold it but it may be difficult to get the clip into place.
Thanks
I see dq250 way easier to work on and better over dq200
Hello, what purpose has that shim ? What can happen if set incorect the shim ? What fault codes can generate a bad setting clutch package? I really appreciate a realy answer.Thanks in advance ...
Hi,
The shim helps to adjust the release characteristics of the clutch and is very important to ensure that the clutch will operate effectively and to give long term reliability. If you don’t set the shim correctly, the clutch may not release or can slip. The fault codes are dependent on the specific vehicle. For more information on these codes, we recommend contacting a local vehicle specialist.
Thanks
@@australianclutchservices7503Hello, many thanks for the answer.I really apreciate it.
@@australianclutchservices7503 I think you just solved my clutch disengagement issue with the reply to this comment.
Hello Türkiye İstanbul video süper tankyou
Hey there,
Could using a pry bar slipped under the clutch pack to hold the clutch drum up affect the readings on the dail gauge?
Didn’t have the special tool, also noticed you guys only use it once the readings have been taken… other videos show them installing the speical tool first.
why you didnt mention to adjust the bottom bearings to match the gearbox hole?
Thanks your video saved my car😂
very concise, thanks
great jobe! great explication! well done!
Where can I get the cover plate to buy? Mine leaks all the time...
Hi,
The cover is included as part of our complete replacement clutch kits. Please visit our online catalogue at www.australianclutch.com.au and contact our friendly sales team through our contact details.
Thanks
where can I find the tool at 3:25, ive emailed asking as well, and got a response but no answer yet
Part number T10303
How do you keep the gearbox flat like that?
Hi Jordan,
We use a small stand that we have made for the displaying the transmission at trade shows, but you should be able to use something underneath to help keep it balanced and level.
Thanks
Nicely made video, good job.
simple,tough wet DCT
From where i can buy them pliers from please
Hi,
These are just circlip pliers that can be purchased through any tools shop etc.
A better name for that style is 'Lock Ring Pliers'.
You are my hero.
Can i reused snap ring?
Hi,
We recommend using the new snap ring provided in the kit for this.
Thanks
Noted. Many thanks
@@australianclutchservices7503 if the old snap ring was a 2.2 why can’t I just reuse or get the 2.2 out the bag?
Hi@@em1ownerify
Each clutch can have a different setup height which would require different snap rings.
Also, there can be wear and tear in the transmission components effecting the end float of the input shaft. It is important to check the different dimensions and then use the new snap rings provided in the kit.
Thanks
Great instructions ! do you offer upgraded clutch packs for the dq250 that can hold more torque ?
Hi,
Thank you for your enquiry. Could you please email sales@australianclutch.com.au with your vehicle details including torque requirements and our friendly sales team will be able to assist you further with this.
Thanks
Hayden
Hi, thanks for the informative video. I have a 2015 CC with the 02E trans. It all of a sudden stopped moving both forward and reverse. When I scanned it, I got a code P0716 (G182 implausible signal). Pls can the G182 cause the car not to move at all? Is there a way to check this sensor with multimeter. I have checked the connector and no physical damage, I have opened the mechatronic cover and the wire of the G182 looks good. before all of this, I have replaced the DSG oil and filter. Is there something else I can do? My car is 32000 miles. Thanks again.
Hi,
Thank you for your comment. In this case we would recommend contacting or taking the vehicle to a local specialist for a diagnosis of this issue.
Thanks
@@australianclutchservices7503
Hi
I write from Croatia , please i need your advice . My mechanic changed the dual cluches and dual Mass flywhell on Passat b8 2.0 tdi DSG , and after the change my car i shaking when i start to drive , only in the start when i put off foot from pedal in the moment when te chutches separates . After is everthynk okej . Is posible that the new clutches Are not good or the mehanic didn’t do a good job , before the changing IT was not the shaking .. please help
Tnx