Where is the direction of the windings? It is more important than the music or the composition of the pieces. The direction of the windings of the copper coil for each section is important, so I will put 😂🌟👎🌟👎🌟👎🌟👎🌟👎🌟👎
I would be interested in relative max. output power of the 3 types or any other data that differentiates them in order to answer the question: why bother with more stators/winding/complexity?
The relative max output power would always be limited, most definitely by the magnets. They will only attract up to a certain point; the magnets are pulled by the electromagnetic properties of the coils, but while electromagnets can be given more power, regular magnets will have a finite limit on power. The stator is the entire part of the motor that has the coil windings, so I assume you were referring to the coil windings in your question. More coils will essentially increase the amount of magnets that can pull the permanent (neodymium) magnets. More windings will increase the voltage that can go through it, which would increase the rpm of it. A thicker cable would increase the maximum amperage and overall torque of the motor. Unsure what you meant about complexity though. Did you mean why multiple coils are continued across the stator? Knowing the gauge of the wire, the number of turns, the number of coils, and the control board's output should be able to give an approximate relative max output power of the three types of motors, but that’s about it.
Is it important the width of the wire? Because I followed all the steps using a 0.5mm one but it doesn't work and I don't know if it depends on which wire you use
Hm, he's using three wires for three phases but, if it's DC it needs to be six wires to change the polarity in the coil. If it's AC, or even if you rely on the field collapse to act as the reversed polarity, there needs to be a return/ground wire.
Hi, Will this motor work with 20A ESC and a servo controller? I replicated this motor with six pole BLDC but is not working with this ESC or should I use only 12V - 36V same controller that you are using? Can you guide me on this please.
did you buy the coil from the description he gave he is a liar we need to use enamelled insulation copper coil but he gave without insulation in the description
why did you put recorded sound of motor from somewhere.It was noticible if you hear the nine pole motor rotate in loop.The speed of the the motor as shown is not that fast i can gaurentee;
greetings !!! BRAVO!!! BRAVO!!! BRAVO !!! MANY MANY THANKS FOR YOUR DETAILED ILLUSTRATION especially the # of turns ... hahaha will you share the info/3d prints on the poles ???
Hello great job. I have a question: did you use the same magnets for each 3 motors? And the magnet link is missing,can you give the dimensions of magnets for each motor? Thank you.
I have doubt about motor stator how can it works without any metal. you can't use any metal in stator and its work how? Motor can't work in plastic stator
Oh the wire has the isolation coating. The end of the wire strip off the coating and tight with the standard knot. I cannot understand the sequence and which side of the end tighten with the other one... I am stupid and lack of observation ability... and the patient!😅😅😑😑
Wiring connection kayse kiye ho bro 1, 2 , 3 , no ke hisaab se ? Startin aur ending wire ka kayse connection bro ? Video mein thheek se pata nahin chal paya.
Почему нас учили что статор мотается только на железе Э305 , а тут голимый пластик и работает , конечно хар-ки будут другие , но это и на порядок дешевле чем из железа
What's the point of carving out a disc shape for the outside of the motor when the magnets are in the middle 🤔 surely it would be easier for winding the coils if those bit of plastic weren't in the way
@@SaravanaKumarJANU @hahahaha.......9216 I thought you had to use a conductive material, like laminated electrical steel or smc, wouldn't plastic just overheat and melt?
This motor converts electrical energy to mechanical energy. To generate energy, you need another source of energy. Don't forget about the law of conservation of energy.
@@MrStrocko а кто сказал, что свист от этого пропеллера, там рядом настоящий мотор свистел, а в кадре было это недоразумение. Хватит быть такими наивными. Если бы так можно было бы, то так и делали бы все заводы. Изучайте физику, чтоб не вестись на подобную лапшу.
Where is the direction of the windings? It is more important than the music or the composition of the pieces. The direction of the windings of the copper coil for each section is important, so I will put 😂🌟👎🌟👎🌟👎🌟👎🌟👎🌟👎
Hi. Would appreciate verbal instructions also
Thanks
Is this power to fly
muito bommmmmmmmmmmmmmmmmmm.
how is wired the coil?
This better show everthing including where the hall efect sensor goes. Every wind your own motor video seems to leave something out.😕
He uses electronic speed controller ESC no need for Hall sensor 🙏
@@akashdeeplakra3583 even if you are using electronic speed controller.... Hall effect sensor is required to locate accurate position of rotor.. 🙏
No hall needed it's a puls signal / mosfets controller
Think of it as
A big rc 3 phase bldc motor.
@@abhijeetkedar1551in the e bike, i removed the sensor cables but it's works very well Elhamdülillah.
@@abhijeetkedar1551I've never seen a hobby brushless ESC that even has pins for a hall effect sensor.
Hello there
very impressive- , Done subscribe your channel -from syoknyadiy channel...
Please show us rotation speed with same voltage in different motors.
Why not use iron steel spacers to amplify your windings..
Of course silicon steel is better or ferrite for the HF
Guess optimum balance for motor weight and thrust ratio
It was a really nice and productive video, thank you.
Can i sell?
I would be interested in relative max. output power of the 3 types or any other data that differentiates them in order to answer the question: why bother with more stators/winding/complexity?
The relative max output power would always be limited, most definitely by the magnets. They will only attract up to a certain point; the magnets are pulled by the electromagnetic properties of the coils, but while electromagnets can be given more power, regular magnets will have a finite limit on power.
The stator is the entire part of the motor that has the coil windings, so I assume you were referring to the coil windings in your question. More coils will essentially increase the amount of magnets that can pull the permanent (neodymium) magnets. More windings will increase the voltage that can go through it, which would increase the rpm of it. A thicker cable would increase the maximum amperage and overall torque of the motor. Unsure what you meant about complexity though. Did you mean why multiple coils are continued across the stator?
Knowing the gauge of the wire, the number of turns, the number of coils, and the control board's output should be able to give an approximate relative max output power of the three types of motors, but that’s about it.
How can I buy this? Do you have to sell?
Tesla stated that the numbers 3 6 9 are the keys to the universe
Kindly show circuit diagram
Is it important the width of the wire? Because I followed all the steps using a 0.5mm one but it doesn't work and I don't know if it depends on which wire you use
Hm, he's using three wires for three phases but, if it's DC it needs to be six wires to change the polarity in the coil. If it's AC, or even if you rely on the field collapse to act as the reversed polarity, there needs to be a return/ground wire.
I think You are confusing the use of the terms pole and slot.
What do you mean by this
6 coils and 4 magnets only ? 9 coils and 6 magnets only ? Why are these magnet not polarizes towards coils ?
Hi, Will this motor work with 20A ESC and a servo controller? I replicated this motor with six pole BLDC but is not working with this ESC or should I use only 12V - 36V same controller that you are using? Can you guide me on this please.
did you buy the coil from the description he gave he is a liar we need to use enamelled insulation copper coil but he gave without insulation in the description
sir I wanted to make a e bike.
please make a habby motor that can run e bike
Excuse me, can you use the XR-105 controller?
Hello bhai Tum isase drone banaa sakte ho Jo motor banae Ho Tum ek video banakar dikhao please do😊😊😊😊😊😊😊😊
In the description: The link to the bldc controller isn't working. Could you fix the link?
Is there a way to make a bldc motor with just 2 wires? like what this guy did:ruclips.net/video/3TTi4TdlCeM/видео.htmlsi=mvNKrhO8EV7C-wz8
why did you put recorded sound of motor from somewhere.It was noticible if you hear the nine pole motor rotate in loop.The speed of the the motor as shown is not that fast i can gaurentee;
asi mismo con estos motores se puede hacer un motor generador las mismas bobinas generan electricidad y yo se como coger esa electricidad
It's not a DC motor. What comes out of the ESC to drive it?
Its actually pulsating DC
Moving part is magnet. So no need brushes. The current from the board is pulsating dc.
Wire Connection bhi explain kiya karo bhaai hamare liye to useless hai ye video hame connection ka
Hi nahi pata aur na hi tumane bataya
NIcely done I would say, really nice.
Input volt ??? And rpm ? 😊
thanks bro😊❤
Tolong jelaskan bagaimana caranya lebih detail penyambungan kawat tembaga dari A B C dan seterusnya hingga hidup
White Ronald Lewis Michelle Gonzalez Robert
greetings !!! BRAVO!!! BRAVO!!! BRAVO !!! MANY MANY THANKS FOR YOUR DETAILED ILLUSTRATION
especially the # of turns ... hahaha will you share the info/3d prints on the poles ???
Hello great job. I have a question: did you use the same magnets for each 3 motors? And the magnet link is missing,can you give the dimensions of magnets for each motor? Thank you.
Hi everyone, I want to know why 3 pole refers to 2 neodymium magnet，6 pole refers to 4 neodymium magnet，and 9 pole refers to 6 neodymium magnet ?
6 coil wire picture send help
Sir how you calculate number of Turns and number of Gauge please 🥺 guide me, I'm ready for the pay for this information
Rất tuyệt vời, cảm ơn bạn
Como coño salen 3 cables de cobre si el cable tiene 2 extremos?
I have doubt about motor stator how can it works without any metal.
you can't use any metal in stator and its work how?
Motor can't work in plastic stator
BLDC motors use much less copper. Therefore it should be less costly. Why its market price is more?
What kind of rpm are you getting on this thing
Oh the wire has the isolation coating. The end of the wire strip off the coating and tight with the standard knot. I cannot understand the sequence and which side of the end tighten with the other one... I am stupid and lack of observation ability... and the patient!😅😅😑😑
This is showing off. I thought it was a tutorial
Nice video But plz add diagram of coils connections
How did you find the number of windings?
I have no idea
Esto rstaria bueno para un coche electrico el rotor iria.con imanes potentes y trabajarlo a 60 120volt cc Arg
Not as quite as I expected but I couldn't do because I don't have thousands of pounds worth of kit to cut out the frames etc 😂
Sir how you calculate number of Turns and number of Gauge please 🥺 guide me, I'm ready for the pay for this information
Mujhe bhi bana na hai bhai saman kaha milega batao Bhai
the rotation of the field with the 9 pole motor is the slowest with high torque, the six is in the middle and the 3 is the fastest with low torque.
Истину глаголишь , сын мой ! (с) А ещё у резистора два конца , а у потенциометра три , во как !
Wiring connection kayse kiye ho bro 1, 2 , 3 , no ke hisaab se ? Startin aur ending wire ka kayse connection bro ? Video mein thheek se pata nahin chal paya.
Plz send wire conection circuit srnd me
Que tenga rotor de 1kilo o 2kilo o 10kilo metronewton por segundo para un coche electrico seria gabuloso
Hello 😂😂😂😂😂👆👆👆👆👆👆
Почему нас учили что статор мотается только на железе Э305 , а тут голимый пластик и работает , конечно хар-ки будут другие , но это и на порядок дешевле чем из железа
What's the point of carving out a disc shape for the outside of the motor when the magnets are in the middle 🤔 surely it would be easier for winding the coils if those bit of plastic weren't in the way
Is it 12 volt or 24 volt, if I make a round of 60 turns not 40 , what happen then how much battery volt I need to run this.
What is the plastic like material used here to wind the copper wire?
Its pvc
It is PLA
@@hahahaha.......9216I thought you had to use a conductive material, like laminated electrical steel or smc, wouldn't plastic just overheat and melt?
@@SaravanaKumarJANU @hahahaha.......9216 I thought you had to use a conductive material, like laminated electrical steel or smc, wouldn't plastic just overheat and melt?
Very nice video, but can you show how to build DIY motor controller for these motors
So I this case Teslas 3 6 9
applies to motor scaling
the number of coils.
Number 3 can be used on Cycle Motor? Can you make a vedio With a Running cycle?
100 % people watch but 2% people's try to make 😂😂😂😂❤️❤️❤️
Are you sure that it is copper, not coppered wire?.. 🤣
What conclusion, RPM, Torsi..??🤔
Plz send wire conection
Over heat and melt pvc
Existem coisas ruins e isso.
cuales son los materiales
Did you check the rpm and thrust of it? If possible check and revert back
What is speed of 9
How would one reduce the noise?
Though nice Job.
Which one is Higher RPM.
Hello dear yes sir that's great I rate you and you is great thank 😊😅
more poles = low speed but increase torque.
It's the same as a stepper motor.
what is thr formule of turns why 100 ı want to learn?
What is the name of the device that connects the electricity of the electric motor?
a bldc controller
BRO WHAT ABOUT INPUT BRO
Inti lilitan kawat sebaiknya besi atau besi lunak.
This motor can work as a power generator at the same time or another type of winding is needed
This motor converts electrical energy to mechanical energy. To generate energy, you need another source of energy. Don't forget about the law of conservation of energy.
Yes you can
How do you determin the dimensions of all the parts?
Takes a lot of maths, Integrals and Inductivity calculus!
Which sizing method do you recommend? since I'm studying aeronautical engineering and my team is assigned to make BLDC
Bro how you use odd number of pole????
надо было для чистоты эксперимента ток потребления показать
Дело даже не в токе потребления а в крутящем моменте. Он около нулевой. Магнитопровода нет вообще....
@@aleks-marно пропеллер то свистит
@@MrStrocko а кто сказал, что свист от этого пропеллера, там рядом настоящий мотор свистел, а в кадре было это недоразумение. Хватит быть такими наивными. Если бы так можно было бы, то так и делали бы все заводы. Изучайте физику, чтоб не вестись на подобную лапшу.
@@aleks-mar Что это вы так возбудились , а ТОЭ и Эл.Машины я изучал тогда когда ваш папа гадил малышом дальше чем видел !
@@MrStrocko я рад за Вас! Изучали, да видать так и не изучили толком ничего, если в такие ролики верите.
why you never show the power supply. ?
Max rpm?
Gira mas lento perontiene mas torque
what is the structure made of?
Is it used to be a cycle motor...
Why do you only have 6 magnets on a 9 pole motor?
Very impressive ... subscribed!
How many turns have you used
Which material is used for making the structure
I also want to know this!
Pvc pipe
its confused how to connect coil connection
Missing measurement power consumption
da para fazer aeromodelo com esses motores?
Super super super your a engen's
👍👋