dji avata esc error | esc problem fix | dji avata disassembly part II
HTML-код
- Опубликовано: 20 окт 2024
- Welcome to our comprehensive guide on addressing the DJI Avata ESC Error and fixing ESC problems. In this video, we delve into the common issues that arise with the DJI Avata electronic speed controllers (ESCs) and provide step-by-step instructions to troubleshoot and resolve them.
If you've encountered an ESC error or are experiencing performance issues with your DJI Avata, you've come to the right place. We walk you through the disassembly process, allowing you to gain a deeper understanding of the Avata's internal components and how they work together.
Our expert team will demonstrate various methods to fix ESC errors, including calibration techniques and other troubleshooting steps. By following our comprehensive tutorial, you'll be equipped with the knowledge and skills to resolve ESC issues on your DJI Avata.
Join us as we explore the ins and outs of the DJI Avata, offering valuable insights into its operation and providing practical solutions for common ESC errors. Whether you're a seasoned drone enthusiast or a beginner, this video is packed with useful information to help you get your DJI Avata back in the air.
Don't let ESC errors hold you back from enjoying your DJI Avata's full potential. Watch our video now and discover the effective techniques to fix ESC problems and confidently perform a DJI Avata disassembly. Remember to like, comment, and subscribe for more helpful content on drone troubleshooting and repairs.
Link to spare parts - s.click.aliexpress.com/e/_DEtcJQR
One prop explode, in mid air and now i have esc error, just tried to upload new firmware but i did not work. @Mrdrone you only change motors? 4 in 1 esc plate? Its not clear in your video what have you changed or how you fix it
Hello friend.. My avata upgrade axisflying 3.5,everytime i start engine all motor spining in second and than stop with notice 'the motor stalled' after install proppeler
Can u explane or guide to fix problem?
Thx, bless u🙏
I never tried hoping to do that
So what was the issue then ? Besides doing pointless stuff ?
In Avata are 3 boards? Rf, esc and mainboard? Is posible changing or are these boards paired?
Yes. Brother it’s possible. But if you change the main board. Gimbal no longer will work. So you have to calibrate with software.
Hello @Mrdrone do you only change motors? All 4 in 1 pdb with esc?
I just replaced the esc only. Not the motors bust sometimes motors gets bad too. So have to check motors also.
Where do you buy the plate on 4 in one for replace esc plate?
If you change just the ESC will the Drone/Flight controller serial number change? Thanks!
No brother it’s not.
@@mrdrone1212 Good morning. I also changed my ESC (but without changing the thermal paste, I hope that the one present will still be "good", but I will dismantle it again in case).
I noticed that the drone is no longer recognized in DJI when you change the RF and not the ESC actually. It's good to note :)
Thanks for the video.
did you change the esc board module or repair the burned one?
is there any chance that can be repaired for small burned-out@@mrdrone1212
Bro wre did u get the new esc
I hope someone can clarify this for me. On the battery for the avata there are 2 "extra" wires besides the +/- one is labeled as TX_RX and the other BAT_ON. Do these wire also carry current? The reason I ask is because I want to experiment and test if I could solder a xt30 connector in place of the original battery connector and use 4s lipos but if i do so where should i connect those 2 extra wires. "BAT_ON" to positive and "TX_RX" to negative? Please help before I end up trying my avata 🤦♂️
yes, you need conect all wires, this two wires is batery control, and avata haveonly 30% power
Pls help, my avata is showing esc auto check error and propulsion autocheck error ater only a couple flights, what is wrong with it and how can i fix it?
Did you try to update the firmware. Or refresh the firmware.
@@mrdrone1212tried that, and resetted the drone, didn't work
hey I need a help.
I changed the esc board module and the drone is giving the tuning sound after i turned on but the gps module light is not blinking.
and the drone doesn't pair with googles and controller. also i ordered and the new gps module and changed but the light is still not blinking. What might be the problem.
i changed esc module and also gps module
Please check everything again. And do the firmware update after. All
@@mrdrone1212 hey I tried everything and updated but it didn’t work
Hello where do you buy the esc plate?
Hello my friend . I have a issue with my avata . After a landing with my drone my gimbal dont work . Im trying to calibrate but i cant . Any thoughts what is going on?
Maybe it damage the gimbal. Try to find authorize dji service center they can check. The problem without disassembling the drone.
Maybe it damage the gimbal. Try to find authorize dji service center they can check. The problem without disassembling the drone.