I see plenty of people working on laptops but very few on PC mainboards. I suppose there's more money in laptops but I like what you're doing. Your content is as good as any of theirs. Too bad this one didn't work out!
You could technically re-ball in an oven. You can't delaminate/popcorn a PDB in an oven because all layers expand the same amount, the only problem is working with the oven door in the way. Then it's just a matter of:- Heat in oven and pull the chip, stencil and paste the balls on the chip, then oven it back on.
Assuming he has a big enough oven, the plastics such as sata connectors, ram slots, pcie slots will melt and caps will bulge. And worst of all, even if he managed to overcome those issues, there is no point in reballing a shorted PCH. PS : He has a hot air station and a pre-heater.
Yes he can do reball or replace the chip without any problem, I am doing reballing and replaceing chip every, day, maybe he don't have experience for that
@@15dejo There was a time i tried doing that with scrap boards, but i always had probelms with warping and the chip as a result not seeting properly, i am currently trying to get a full sized preheater to do BGA work!
The motherboard might have liquid damage from running in an humid environment as well. Humid environment might've caused some short and that brought down the pch
why the pch is going to die? as i saw your explanation(very thanks for full explanation of schematic) nothing else is broken, just because of going too much hot pch going to die?
At the beginning we already saw very low resistance on the PCH! Also a signal coming from the PCH is missing! and third it goes to over 100 degrees within like 2 seconds! Any more reasons to belive that the pch is gone?
@@MainboardMedic sorry, i just want to know why pch is going to die,i mean i`m a desktop user, what can i do to prevent my mainboard PCH not die suddenly, i didn`t mean that the reasons is not good
@@pegmanashhad7771 There is basicly nothing you can do as an end user to prevent this from happening! Only few thing are: keep your pc clean and the tmeps low and dont do anything bad with the USB because that is almost directly connected to the PCH. But they often sadly just die!
I see plenty of people working on laptops but very few on PC mainboards. I suppose there's more money in laptops but I like what you're doing. Your content is as good as any of theirs. Too bad this one didn't work out!
Exactly that, there is basicly no money in ATX desktop board, exspecially with all the dead PCH´s i am getting!
@@MainboardMedicwhat is the main cause of killing PCH? Is ti some high end Mosfet short circuited?
@@asv5769 I am really not sure to be honest.
As per usual. An amazing sleuthing job! Very entertaining logical progression through the circuitry.
You could technically re-ball in an oven. You can't delaminate/popcorn a PDB in an oven because all layers expand the same amount, the only problem is working with the oven door in the way. Then it's just a matter of:- Heat in oven and pull the chip, stencil and paste the balls on the chip, then oven it back on.
Assuming he has a big enough oven, the plastics such as sata connectors, ram slots, pcie slots will melt and caps will bulge. And worst of all, even if he managed to overcome those issues, there is no point in reballing a shorted PCH. PS : He has a hot air station and a pre-heater.
Yes he can do reball or replace the chip without any problem, I am doing reballing and replaceing chip every, day, maybe he don't have experience for that
@@15dejo There was a time i tried doing that with scrap boards, but i always had probelms with warping and the chip as a result not seeting properly, i am currently trying to get a full sized preheater to do BGA work!
The motherboard might have liquid damage from running in an humid environment as well. Humid environment might've caused some short and that brought down the pch
It’s not a dip switch, it’s called a potentiometer.
It might even be an encoder haha!
why the pch is going to die? as i saw your explanation(very thanks for full explanation of schematic) nothing else is broken, just because of going too much hot pch going to die?
At the beginning we already saw very low resistance on the PCH! Also a signal coming from the PCH is missing! and third it goes to over 100 degrees within like 2 seconds! Any more reasons to belive that the pch is gone?
@@MainboardMedic sorry, i just want to know why pch is going to die,i mean i`m a desktop user, what can i do to prevent my mainboard PCH not die suddenly, i didn`t mean that the reasons is not good
@@pegmanashhad7771 There is basicly nothing you can do as an end user to prevent this from happening! Only few thing are: keep your pc clean and the tmeps low and dont do anything bad with the USB because that is almost directly connected to the PCH. But they often sadly just die!
@@MainboardMedic thanks, i`m really excited to see your reaction to my question and very thankful, i hope best thing happen for you my friend
Liquid Cooling accident where some of the fluid leaked? 😕🤷♂
Really looks like that!
i think u can do it!! buy solder balls and heat plate.. replace chip and get Clean Intel ME Bios.
Hello🤝Good job 👍👍👍👍👏👏👏👋👋👋👋👋👋👋
Hey there I got a question, The msi z790 s wifi ddr5 board has 5v argb pads without the pins, is it possible to solder the pins to the pins?
Would need to check if the R G B get signals or not or else you might only have one color or just the 5V there!
Where did you get that nice POST card?
There are links in the description.
Ha, ha, ha! Insanely expensive repair! 🤣
You can't win them all
First.