What a great video! but I would really have loved to see how you connect the switch with to the other components. What do you do with the black and white cables?
Sorry, took a long time to make the video and I know I missed some details. Black goes to ground, white goes to any of the line of out, best after the pickups, at the switch or even jack. Thx
@@chelseacollectibles8827 thanks very much for your answer, I'm really not good with this kind of tasks but I decided to try it myself for once (I should have choosen an easier project lol) and your video and indications are gonna help me a lot. Thanks again
If I were to add this to a strat type guitar I would just remove the one tone so you still have the 3 way switch for pickups and then this rotary as the last control. You may want to also check out the old Esquire wiring, that uses a 3 way switch but only has 1 pickup.
Can this switch be used as a 6 way pickup selector for three single coil pickups? I’m looking for a replacement for the danelectro select-o-matic pickup selector.
Yes, you would need to figure out what wiring options you need. There are two types of switches, break before make is what I believe you will want, that is what is used for the switch also. It breaks the contact before making the new one so you don't have any bleed while switching.
I offer this as a kit where you assemble, I make the switch so you can just drop in and I offer this inside of a pedal case so you don't have to mod your guitar. Please check out my reverb shop. Thx
What value choke do you have and where did you get it? I was looking at 1.5H transformer style chokes, but yours looks way different. Planning on making a variation of this for a 3 band passive EQ using a notch filter for mid cuts.
I get these from overseas, its an Axial Inductor. You can use any conductor, axial, radial, there are a few types. Since no electricity is going through it you can use a lower value, some people even make them without any choke/inductor. As for value, I'm not sure on value right now, I was getting a value that would work and also fit inside the cavity of the guitars.
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
What a great video! but I would really have loved to see how you connect the switch with to the other components. What do you do with the black and white cables?
Sorry, took a long time to make the video and I know I missed some details. Black goes to ground, white goes to any of the line of out, best after the pickups, at the switch or even jack. Thx
@@chelseacollectibles8827 thanks very much for your answer, I'm really not good with this kind of tasks but I decided to try it myself for once (I should have choosen an easier project lol) and your video and indications are gonna help me a lot. Thanks again
Great stuff, is there a switch for a standard Stratocaster with 3 single coils and that can utilize the tone control?
If I were to add this to a strat type guitar I would just remove the one tone so you still have the 3 way switch for pickups and then this rotary as the last control.
You may want to also check out the old Esquire wiring, that uses a 3 way switch but only has 1 pickup.
Qué función tiene el choke en el circuito? Para qué sirve?
Gracias y saludos
There is a lot of info on what the choke does, you can make this with and without the inductor / choke. It will make this a notch filter. Thx
Can this switch be used as a 6 way pickup selector for three single coil pickups? I’m looking for a replacement for the danelectro select-o-matic pickup selector.
Yes, you would need to figure out what wiring options you need. There are two types of switches, break before make is what I believe you will want, that is what is used for the switch also.
It breaks the contact before making the new one so you don't have any bleed while switching.
Thank you kindly!
Would it be possible to use a single resistor wired to the input and ground?
The schematics say to put a resistor on each and also since they aren't expensive I just put one on each cap.
Thx
Do you have a deal where the package comes with all the capacitors already attached? Thank You.
I offer this as a kit where you assemble, I make the switch so you can just drop in and I offer this inside of a pedal case so you don't have to mod your guitar. Please check out my reverb shop. Thx
What value choke do you have and where did you get it? I was looking at 1.5H transformer style chokes, but yours looks way different. Planning on making a variation of this for a 3 band passive EQ using a notch filter for mid cuts.
I get these from overseas, its an Axial Inductor. You can use any conductor, axial, radial, there are a few types. Since no electricity is going through it you can use a lower value, some people even make them without any choke/inductor.
As for value, I'm not sure on value right now, I was getting a value that would work and also fit inside the cavity of the guitars.
gerat, is there a circuit pdf someware?
Not that I know of, that's why I made a video. Thx
What are the resistor values you use?
10M resistor. Thx
Wow