Great video - I did not succeed to enter the config menu even after pushing shortly the i button twice - thanks to this video I got the confirmation and succeeded finally
Hello in the display manual dp-c18 reports Sport and Eco modes but how can you change? i tried pressing + for more than 2 seconds but it doesn't change? can you tell me if it is possible to change and how to make this change?
I find it I interesting that you need to reset the time clock every time you reconnect the battery. In my case, that would be everyday as I recharge mine inside and park the bike in an unheated garage.
Does this work with 52V battery? If the battery is fully charged (which can go to ~ 57V) would that still work ok? Isn't this better or worse than 860? Thanks a lot.
Hello... TFT and Sunlight Readable TFT are vastly different in terms of not washing out in Full Sunlight.. (the place we need to be able to get info from). When is Bafang going to offer a display that doesn't washout in the sun..? I have no problem seeing the 961c and 965c... but i need Speed indicator, Wattage consumption, and Volts.. When you are trying to optimize range, you need to find that perfect spot between Power level and Gear Ratio.. But unless you can see the watts, it is nearly impossible to fine tune the bike for range. Can you get a hold of Bafang and let them know that they need to make a "Sunlight Readable TFT" display.. Not TFT alone.. ? TFT is TransFlecTive screen... Sunlight Readable TFT polarize the sunlight hitting the screen so that you can see it. :)
BTW, Ebike enthousiest have money to spend.. And we don't want to waste money trying models that don't work in most Ebike environments. I'm ready to spend a little more for sight.
I agree that most ebike displays are hard to see in direct sun. The DPC18 is easily readable in direct sun. (Its backlight is also adjustable.) At full intensity, it is more vivid than my tablet or Samsung phone. The Watt meter is large & visible at a glance. (I wish the battery & trip data were half that big!)
@@Downham34695 Luna the reason they say that is because they NOT make money on it but there is a way i did find someone with the image file i just haven't had time to do it . I even found the software as well . Because after this flood here in NY I am having to replace 2 of my battery's on my bikes and the controller on the Ultra motor I will NEVER buy anything from those LOOSERS SCUMVBAGS at Luna Cycle They do NOT honor there own warranty and try to BLAME every Fault on the CUSTOMER.
I bought the front hub motor kit with this display option. After I paid I was told it only works with pedal assist. I only have the front hub. Will this work?
is there a way to reset everything to factory settings.I got this display as a gift from a friend and the total mileage is left from his bike and mine is new so I want to reset the total mileage to zero
Thanks. You never went over how to reset trip details? How do you reset trip odo on the fly? reset top speed on the fly? I can't seem to find any of that info? How are these manually reset?
How do u change the timeout, when the display auto turns the bike off. It is way to short a d very annoying to have to keep restarting it after short breaks
is it compatible with all Bafang motors? I would like to know if it is compatible with Bafang motor to Bafang alloy wheel rear hub. RM GOFO.259.D.07. 36v 250w.
in this display, for Wheel Settings they want inches, where is this measurement, derived? No info on rims or tires do I measure the circumference? it's like 86 inches! I just love stupid Q"s
Heya, does anyone know if there is a setting to change the massive performance drop once the battery hits 20%. I'd rather the 'battery save mode' kick in at 10% batt life. Being in a hilly area I have to charge the battery back up each time it drops to 20%. Much appreciated
Why did you film this inside..? could it be that you can't see these Full Color Bafang displays in the sun..? If the 965c or the 961 had a Speed, Volts and Wattage indicator, i would gladly spend a ittle extra..
Nah, unlike many ebike displays, the DPC18 is highly visible even in direct sun. It's even more vivid than my tablet or Samsung phone. (Though much lower res, & lower refresh rate.) The Wattage indicator is very prominent, easy to read at a glance. I wish the battery indicator were as large!
The same display on Bafang m500 I wash my bafang bike since then the bike is off, it is on only when it is on charger and shows 100 percent but when you remove the charger the bike goes off immediatelly i dont know what to do can someone help? please
my ebike is on 48V battery, and the display always only shows 60% battery when I have fully charged the battery, please help me More info, the display I use is DPC18
Hello, I have an electric scooter with LCD (smaller) and same connector (5 pin) and I would like to know if this display is compatible for other types of devices, such as my scooter. The connection is the same, once again, but I wonder if this display is reserved only for electric bikes or for the Bafang brand only? Thanks in advance.
i have a similar question. how does the controller know exactly where the speed sensor/magnet are located. i installed a conversion kit so the location of these isn't fixed
@@richb7524 Im presuming you are referring to how close/far from the center hub the magnet is set. If that the variable you are referring to its quite simple. It doesn't matter. The magnet has to complete a revolution and if its near or far its still one revolution of the wheels diameter.
@@FREEHAND.WETGRINDER I was thinking the same thing but the controller has settings that can go as low as a 9 in tire- threw me for a loop. I plugged in my size, 26, and rode a known distance; odometer was on the money. I just completed my build yesterday. Thnx for the reply
@@johnblakewaller9322hi, yes it is Nice display i have one, i will install it in my ebike just wan to know everytings about that befor install it. Thanks ✌
It is a shame it does not have a brake symbol, wich ligts up when hydraulic handbrakes ar aplied, so motorpower is cut, so you can adjust the hydraulic brakesensors easily
@PaPa Frampton Bafang motor controllers are notorious for shipping with no config done. In particular, their torque sensing motors such as the Ultra m620, _aren't calibrated_ to provide accurate torque sensing. The "default config" leaves the sensor's Base Voltage set to 0, which is _NEVER_ correct. At 0 mV Base Voltage, any pedal rotation at all registers as ~12Kg of pedal force! Accurate baselines, range from 732 to 763 milliVolts. For Bafang motors _without_ torque sensing, the only control variables are pedal cadence & throttle. Throttle is smoothest when set to Current rather than Speed scaling mode. Pedal Assist requires calibration of KeepCurrent, Decay rate, & Decay time, to maintain steady assist. Setting the Slow-Start Mode to 7 helps reduce jerk when the motor engages.
Well I can tell you that this display will not work with the bbshd motor. I think it's very frustrating that suppliers of bafang motors do not tell you this. You will be limited to around 45kph and will only have 5 levels of pedal assistance. If I paid for a motor that is meant to have 9 levels and able to do close to 100 kph I want that. Bafang I don't believe are at fault rather than the suppliers like I said are.
I need help.... My speed limit tuner and the wheel size is under information instead of display settings... Hence I am unable to change the speed limit.... Please help me change it. 🙏🏻
This means that your display is one that received a firmware update from Bafang and it has locked out access to the Eco/Sport settings. Holding the + button down will not work, no matter how long you hold it down. The other concern is that the wheel size and speed limit are not able to change, either. I was told Bafang pushed this firmware update to its newer DPC-18 displays without even telling the retailers they did it. Bad Bafang! My advice to you is to contact your retailer and ask them to send you another display - one without the firmware update. That is what I have done because I'm in the same boat as you are. Other than that issue, this is a great display with beautiful colors and easy to use input pad. What brand of ebike do you have?
@@tenaeastburg1457 Working with distributor on replacing controller or display. Bike is great fast and powerful. Just need to be able to cruise sometimes and not break the speed barrier. Thanks for info.
My name is Debi and I have a bafang ,dcp18,I think, electric bike with a stuck password on my odometer I have tried dummy password that do not work and I need help getting my odometer back on. I put my own password in that it will not accept.
Bafang system are made in China 🇨🇳: Warning ⚠️ label should be on all China 🇨🇳 ebikes, do not buy ebikes make in China 🇨🇳 they do not share electric ⚡️ schematic diagrams when your ebike goes on the frites you will be on your own trying to repair it. Only buy American 🇺🇸 make ebike with American 🇺🇸 parts if you can not find an American 🇺🇸 made ebike just don’t buy one get yourself a motorcycle 🏍 and ride like a fat American 🇺🇸.
If you have a simple +/- two-pin connector, there is no way to receive this information from the batteries BMS. Having just +/- and no data link is one of the advantages and reasons I decided to buy Bafang motor. I can use whatever battery, cheap and easy - no weird error codes which can stop operation.
Excellent little tutorial, no padding or unnecessary twattage. Good Job!
Fantastic video 👍,Just bought a bike with this system and had no idea how to operate it,this gave me all the information I needed 😊
Same thing.. Bought a EMTB last week. No idea how to use it. But I'm hoping the 9 levels of PAS gives me a softer level on 1 than does the 5 level.
Hi bro my bafang hub motor is 9 speed cassette and my bike is 7 speed cassette now I don't know what to do can you please tell me thanks
Geachte heer, mevouw,
Ik ontvang de beschrijving graag in het Nederlands
This isn't programming... He's just going through the settings!
Thank you mate. You have helped me believe me. Thank you
Great video - I did not succeed to enter the config menu even after pushing shortly the i button twice - thanks to this video I got the confirmation and succeeded finally
Thank you! Great review! 👍 I live in Russia and I don't know English very well🙃
Thank you! It is very helpful for me.
Hello, Great video. May I know how to reset/clear the error codes that are on the error codes section?
Push plus minus and pwr buttons twice togerher
can you confirm that if I change to my bike, and I put this display, I increase the speed without intervening on other cosw?
My unit won’t allow me to adjust the max speed and it’s located in information rather than settings?
Do these work on the M420 motor to circumvent the EU version speed limit?
Have you found solution brother?
@@ahmedas6886 Have you found solution brother?
Hi Nicly dun.very god settings.👍👍👍
hello. why my display doesn't have 'Max PAS' setting. thanks
How do you remove speed limit?
How do you reset to factory settings? When there is no factory reset settings on the menu settings?
Hello in the display manual dp-c18 reports Sport and Eco modes but how can you change? i tried pressing + for more than 2 seconds but it doesn't change? can you tell me if it is possible to change and how to make this change?
Same... Did you work it out? I haven't
Press “I” and + to toggle Eco and Sport mode. Can also change in menu.
I find it I interesting that you need to reset the time clock every time you reconnect the battery. In my case, that would be everyday as I recharge mine inside and park the bike in an unheated garage.
Does this work with 52V battery? If the battery is fully charged (which can go to ~ 57V) would that still work ok? Isn't this better or worse than 860? Thanks a lot.
As long as the display and battery are labeled as 52 volt. All or most batteries are of higher voltage than stated when fully charged
Are you able to use the USB port to make the changes from your computer?
Why is there no RANGE choice when you cycle through options? Other videos show this option with this display.
I'm seeing Range on mine? What is it anyways? Is it a guess-timate of how many km's I can ride before batt is to low?
Does this display work with the front motor
The wheel size and Speed Limit are not visible on my Svitch XE+ bike which uses a Bafang DPC 18. How do I get those options ?
What motor are you using? Some controllers will not work with certain motors.
Same here. I have an M600 motor
@@walter9724it's a bafang 250w motor
THANK YOU FOR THE EXPLANATIONS!!
Hello... TFT and Sunlight Readable TFT are vastly different in terms of not washing out in Full Sunlight.. (the place we need to be able to get info from). When is Bafang going to offer a display that doesn't washout in the sun..? I have no problem seeing the 961c and 965c... but i need Speed indicator, Wattage consumption, and Volts.. When you are trying to optimize range, you need to find that perfect spot between Power level and Gear Ratio.. But unless you can see the watts, it is nearly impossible to fine tune the bike for range. Can you get a hold of Bafang and let them know that they need to make a "Sunlight Readable TFT" display.. Not TFT alone.. ? TFT is TransFlecTive screen... Sunlight Readable TFT polarize the sunlight hitting the screen so that you can see it. :)
BTW, Ebike enthousiest have money to spend.. And we don't want to waste money trying models that don't work in most Ebike environments. I'm ready to spend a little more for sight.
I agree that most ebike displays are hard to see in direct sun.
The DPC18 is easily readable in direct sun. (Its backlight is also adjustable.)
At full intensity, it is more vivid than my tablet or Samsung phone.
The Watt meter is large & visible at a glance. (I wish the battery & trip data were half that big!)
Can This Increase Maximum Speed Over 25 MPH Thanks Also What Display Will Work For My Himiway Cruiser Seems To Be A lot Of Different Units Thanks
I have the dual mode (eco/sport) DPC 18 is there a way I can flash mine and get the same as your with 9 pass assist
Did you ever get an answer to this?
@@Downham34695 No they never replied to me even after many messages
@@pharrohku5922 I got a reply from Luna and they say there is no way to do it.
@@Downham34695 Luna the reason they say that is because they NOT make money on it but there is a way i did find someone with the image file i just haven't had time to do it . I even found the software as well .
Because after this flood here in NY I am having to replace 2 of my battery's on my bikes and the controller on the Ultra motor I will NEVER buy anything from those LOOSERS SCUMVBAGS at Luna Cycle They do NOT honor there own warranty and try to BLAME every Fault on the CUSTOMER.
@@pharrohku5922 good to know. I’m sure there is a way to do it, I’m just not sure how to flas firmware on the display.
I bought the front hub motor kit with this display option. After I paid I was told it only works with pedal assist. I only have the front hub. Will this work?
is there a way to reset everything to factory settings.I got this display as a gift from a friend and the total mileage is left from his bike and mine is new so I want to reset the total mileage to zero
Mine does non show MAX PAS can someone tell me why?
same as me
Does this display give range?
My display is version DPC18.C 1.3 and my speed limit & wheel size are grayed out, so I can't change it...
Have you found a solution, ive got same issue nowm
@@ahmedas6886 nope, but my retailer says, he can do it
I need a display which light up or visible at night
Will this work on non bafang bikes
can you use the usb to charge a usb rechargeable headlight?
Thanks. You never went over how to reset trip details? How do you reset trip odo on the fly? reset top speed on the fly? I can't seem to find any of that info? How are these manually reset?
It’s very useful.
Thanks a million.:)
Hello why if you replace a broken drive unit with a used good one,the oddo keeps given the total of the broken one,not the new one thx
How do u change the timeout, when the display auto turns the bike off. It is way to short a d very annoying to have to keep restarting it after short breaks
is it compatible with all Bafang motors? I would like to know if it is compatible with Bafang motor to Bafang alloy wheel rear hub. RM GOFO.259.D.07. 36v 250w.
Hi, I have forgotten my pass number how can I reset with new number? Thanks if you can help.
How do you toggle sport mode and switch between sport and eco mode on the fly?
Hold the + button down and it will switch to the other mode.
Does this work on 500w front hub kit from bafang
Fantastic thank you
in this display, for Wheel Settings they want inches, where is this measurement, derived? No info on rims or tires do I measure the circumference? it's like 86 inches! I just love stupid Q"s
Heya, does anyone know if there is a setting to change the massive performance drop once the battery hits 20%. I'd rather the 'battery save mode' kick in at 10% batt life. Being in a hilly area I have to charge the battery back up each time it drops to 20%. Much appreciated
Mine looks the same, but has a speed limit that can not be changed. Anyone know how to remove it?
Yea my Wheel Size and Speed Limit are hard coded?
im using bafang 52v bbshd bafang 1000w with same display. and i can't find "MAX PAS" how can i find it???
Apparently some came with different software on them. If yours has Sport/Eco mode, you are locked at 5 and cant change Max PAS
missing info where set power consumption in Apms
What if I have a wheel size of 27.5?
I don’t have a MAX PAS option on my computer.
I don't have one either ?
Me either
My controller has 5 PAS modes. Can I add more modes to it?
My button controller only has a power button and the plus and minus, there is no information button on lights button... How to use?
Why did you film this inside..? could it be that you can't see these Full Color Bafang displays in the sun..? If the 965c or the 961 had a Speed, Volts and Wattage indicator, i would gladly spend a ittle extra..
Nah, unlike many ebike displays, the DPC18 is highly visible even in direct sun.
It's even more vivid than my tablet or Samsung phone. (Though much lower res, & lower refresh rate.)
The Wattage indicator is very prominent, easy to read at a glance. I wish the battery indicator were as large!
It doesn't have current adjustment? 20 or 25 amps for example?
You need a bafang programming cable to connect to the batteries BMS to do that.
Can I change the DPC18 that comes with the Ultra Drive System to another controller?
Is bafang SW102 possible?
yes
What is the most recent, DPC-18 or 860c ?
860c
Does the 860c work on 500w bafamg front hub kit
how to unlock the speed limit change ?
mine is speed is locked at 2kmph,
need to change it please help me
How High Does Speed Limit Go Up To Thanks
99
What about that clock on the display. Will it remember ghe time if battery is disconnected?
Mine does; the trip data is retained, too. (There is probably a CR2032 battery in there.)
I recommend the 500C display.
Why does some of these displays say 1500 max and some say 750 watt max on the display?
What motor is this compatible for because I'm running on a 750W bafang motor ?
I have this display with a 750W Bafang hub motor.
@@j-wray Will it be compatible with my 750W Wheel Hub Motor?
@@calvintanner7897 No idea. It works with a Bafang 750W that's the only thing I have to go by.
Hi bro my bafang hub motor is 9 speed cassette and my bike is 7 speed cassette now I don't know what to do can you please tell me thanks
I have the same display… and I’m trying to find the hard rest 😕
The same display on Bafang m500 I wash my bafang bike since then the bike is off, it is on only when it is on charger and shows 100 percent but when you remove the charger the bike goes off immediatelly i dont know what to do can someone help? please
my ebike is on 48V battery, and the display always only shows 60% battery when I have fully charged the battery, please help me
More info, the display I use is DPC18
same here. But I changed to Voltage display and this works for me.
Kann mir einer helfen ich hab Fischer ebike hindermotor 1724 von 2019 was brauche ich und wie ? Lg
how to reset original parameters ?
Hello, can I install hydraulic brakes with this display?
Yes. You will need hydraulic brake sensors from Bafang. They mount to your brake handles.
Speed Limit dont work for me, I have set 25kmh but the bike still goes over 40kmh, can someone say why?
The bike can go as FAST as you can padle bud the motor will push for you only till 25 km/h is reached
Make sure your wheel size is set correctly.
How do you turn the head light on?
It’s in the video at 1:21
Hello, I have an electric scooter with LCD (smaller) and same connector (5 pin) and I would like to know if this display is compatible for other types of devices, such as my scooter.
The connection is the same, once again, but I wonder if this display is reserved only for electric bikes or for the Bafang brand only?
Thanks in advance.
bafang only
@@yuzhaiguo409 Thank you bro. 😊
NOW I HAVE THE POWER, MUAHAHAHA
When setting wheel size is it actual size with tire on or rim size? my 26" rim with tire is 29"
The "Key word" is wheel size, not rim size..
i have a similar question. how does the controller know exactly where the speed sensor/magnet are located. i installed a conversion kit so the location of these isn't fixed
@@richb7524 Im presuming you are referring to how close/far from the center hub the magnet is set. If that the variable you are referring to its quite simple. It doesn't matter. The magnet has to complete a revolution and if its near or far its still one revolution of the wheels diameter.
@@FREEHAND.WETGRINDER I was thinking the same thing but the controller has settings that can go as low as a 9 in tire- threw me for a loop. I plugged in my size, 26, and rode a known distance; odometer was on the money. I just completed my build yesterday. Thnx for the reply
is this compatible with the bafang M600 motor?
I want to lower the third speed program to ride at the same speed as the other bikes. how to do , please :)
You need "USB programming cable" and then you can change the speed % for each PAS level. Google for it - Bafang BBS programming
hi,
is the bafang dpc18 display can use for 52 volt ebike?
lg
Yes I have 52v17.5amp and works fine
@@johnblakewaller9322 thanks 👍
@@makeyourownsystem2425 its actually a really good display and pretty much spot on with KLM distances and speed
@@johnblakewaller9322hi,
yes it is Nice display i have one, i will install it in my ebike just wan to know everytings about that befor install it.
Thanks ✌
No you cant use it with 52volt 30amp pack, battery when it fully charges and you turn the display on it throws code 7 and disables the motor
I gir a new battery on this system. But when its fully charged its says it's only 80% when its fully charged. Any ideas
mine also only reads 75% no matter what battery i use and fully charged
It is a shame it does not have a brake symbol, wich ligts up when hydraulic handbrakes ar aplied, so motorpower is cut, so you can adjust the hydraulic brakesensors easily
@PaPa Frampton Bafang motor controllers are notorious for shipping with no config done.
In particular, their torque sensing motors such as the Ultra m620, _aren't calibrated_ to provide accurate torque sensing. The "default config" leaves the sensor's Base Voltage set to 0, which is _NEVER_ correct. At 0 mV Base Voltage, any pedal rotation at all registers as ~12Kg of pedal force! Accurate baselines, range from 732 to 763 milliVolts.
For Bafang motors _without_ torque sensing, the only control variables are pedal cadence & throttle.
Throttle is smoothest when set to Current rather than Speed scaling mode. Pedal Assist requires calibration of KeepCurrent, Decay rate, & Decay time, to maintain steady assist. Setting the Slow-Start Mode to 7 helps reduce jerk when the motor engages.
56mph... sounds safe for an ebike.
Does this model have ECO and sports mode
Yes.
@@europass1 how come mine only has ECO mode how can I get sport mode to appear please
With bbs01b you have eco and sport.. Mayby try programming trough data cable?
@@europass1 I think I have bbshd 1000watt
A 1000 watt and still need sportmode?😂
Will I lose the odometer distance 1027 klm if I remove the battery thanks
Well I can tell you that this display will not work with the bbshd motor. I think it's very frustrating that suppliers of bafang motors do not tell you this. You will be limited to around 45kph and will only have 5 levels of pedal assistance. If I paid for a motor that is meant to have 9 levels and able to do close to 100 kph I want that. Bafang I don't believe are at fault rather than the suppliers like I said are.
Just set “MAX PAS” to 9 in settings, and it will work. I did the same
I need help.... My speed limit tuner and the wheel size is under information instead of display settings... Hence I am unable to change the speed limit.... Please help me change it. 🙏🏻
Same here. My bike has only one speed Fast!!! How do you turn them down?
This means that your display is one that received a firmware update from Bafang and it has locked out access to the Eco/Sport settings. Holding the + button down will not work, no matter how long you hold it down. The other concern is that the wheel size and speed limit are not able to change, either. I was told Bafang pushed this firmware update to its newer DPC-18 displays without even telling the retailers they did it. Bad Bafang! My advice to you is to contact your retailer and ask them to send you another display - one without the firmware update. That is what I have done because I'm in the same boat as you are. Other than that issue, this is a great display with beautiful colors and easy to use input pad. What brand of ebike do you have?
@@tenaeastburg1457 Working with distributor on replacing controller or display. Bike is great fast and powerful. Just need to be able to cruise sometimes and not break the speed barrier. Thanks for info.
When I press walk mode it’s full speed ahead feels like
My name is Debi and I have a bafang ,dcp18,I think, electric bike with a stuck password on my odometer I have tried dummy password that do not work and I need help getting my odometer back on. I put my own password in that it will not accept.
Wheel size where password protected on mine, so damn stupid! Luckily I could find it on the webb and it was 1919 if anyone else needs it.
Soy de España y tego una pantalla como esta no se ingles y no me entero de nada algun video en español poorfa
5 v at 500mA will run a light .
Looks like they're not answering the questions people've been asking.
Does anyone know what happens if you fail to enter correct password upon startup more than three times?
А что по русски нельзя?
Tutto quello che stiamo dicendo in inglese non puoi trullo in italiano. Grazie
Bafang system are made in China 🇨🇳:
Warning ⚠️ label should be on all China 🇨🇳 ebikes, do not buy ebikes make in China 🇨🇳 they do not share electric ⚡️ schematic diagrams when your ebike goes on the frites you will be on your own trying to repair it. Only buy American 🇺🇸 make ebike with American 🇺🇸 parts if you can not find an American 🇺🇸 made ebike just don’t buy one get yourself a motorcycle 🏍 and ride like a fat American 🇺🇸.
Yeah, American bikes have parts from China....shushhh
graag in gewoon Nedrelands
Would this be compatible with the 750W motor or would I need to upgrade both the motor and the display controller?
Hy , I have a question. Why I can't see how many times I've charged the battery, it's seems that the battery charge cycles counter it's not working.
Over a year since this video was released, and still this is not available........
If you have a simple +/- two-pin connector, there is no way to receive this information from the batteries BMS.
Having just +/- and no data link is one of the advantages and reasons I decided to buy Bafang motor. I can use whatever battery, cheap and easy - no weird error codes which can stop operation.