WIRELESS Single Handed Mechanical Keyboard

Join the Discord: scottokeebs.com/discord
ScottoFrog: scottokeebs.com/scottofrog
~ Links ~
Find out more about the project: scottokeebs.com
Donations are greatly appreciated: bit.ly/41odBEu
Become a patron: / joe_scotto
~ Handwiring Tools ~
TS100 Soldering Iron: amzn.to/3LCsrkb
D24 Chisel Tip: amzn.to/3VFxiES
63/37 Solder: amzn.to/3uBlMPu
Wire Strippers: amzn.to/3LZez4F
Electric Screwdriver: amzn.to/45Jxg3v
~ Handwiring Parts ~
1N4148 Diodes: amzn.to/3Ccljbb
16g Copper Wire: amzn.to/3xLDVvJ
Raspberry Pi Pico: amzn.to/3HglCVb
Arduino Pro Micro: amzn.to/3HkR9Fn
Ethernet Cable: amzn.to/3uyaOKr
M2x6mm Screws: amzn.to/3UI1bDH
M2x8mm Spacer: amzn.to/3Y4KzJ3
M2 Heat Set Insert: amzn.to/3WjklB9
Durock Stabilizers: amzn.to/3FgcLQR
~ 3D Printing ~
Ender-3 Pro: amzn.to/3VIWryL
Ender-3 Max: amzn.to/3PQOHsP
PEI Magnetic Bed: amzn.to/3Hi7URx
Dual Z Upgrade: amzn.to/3h7DTJy
BLTouch Auto-Leveling: amzn.to/3UGEBv8
Sonic Pad: amzn.to/3ZQa7ea
Deburring Tool: amzn.to/48MjXlB
Elegoo Filament: amzn.to/3rG3T4f
~ Favorite Cheap Switches ~
Gateron Milky Yellow: amzn.to/3Bk0Cci
Akko Lavender Purple: amzn.to/3VJy440
~ Social ~
/ joe_scotto
/ joe_scotto
/ joe_scotto
~ Community ~
ScottoKeebs Discord: / discord
Handwired Keyboards Reddit: / handwiredkeyboards
~ Disclaimer ~
Some links may be affiliate links where I will make a small commission.
#mechanicalkeyboard #3dprinting #arduino

[@andre.ramos.1234]

Hey Joe
I love your keyboard and you inspire me.
I see that you always glue the boards to the base of keyboard. And it is ok because it is permanent solution and keyboard is not supposed to be changed frequently.
Can I give a suggestion to you so instead of glue? My idea is to have a small stripe that you put over the board and have 2 screw on both tops.
I didn't try it but I will on my next keyboard.
Just an idea.
For me the perfect solution would be to screw the board but there are no space for screw on it.
keep the good work

[@andre.ramos.1234]

even so, i love your solution, is very clean

[@andre.ramos.1234]

...eventually you can glue a nut on the border of the board 😜 so after you can screw it to the base

[@joe_scotto]

I've actually switched to UV resin now that looks cleaner. I like to glue them in place because I can solidify the connections to prevent them ripping off and it helps reinforce the USB port.

[@andre.ramos.1234]

can this nice!nano be used with qmk frmware?

[@joe_scotto]

The nice!nano can only be used with ZMK to my knowledge.