Well now - Aneng is finally stepping up their game for real with some meaningful improvements and additions. Now if they want to keep the price same or lower and add a more vivid display, divorce the backlight from the flashlight and make the mA range 500 to 600 mA this one could be a real keeper as it seems to perform nicely otherwise, but price is a tad high. 25,000 count dual display is a real standout for Aneng, heres hoping for this one to blossom in the future.
Usually I’m not a fan of Aneng multimeters, but this one is all right. Decent accuracy, nice ranges (except for mA), better than usual input protection, good resolution, dual display is always nice to have. The bar graph doesn’t seem that fast though, but hey, at least it’s there. 👍
You’re right, $54 is a little too pricey for that. In this price range I would personally go for Uni-t just because their overall quality is more consistent, or wait for this one to go on sale.
Interesting input protection concept. The MOVs are usually on the voltage input as that is the mode that the meter will suffer from voltage spikes. Voltage spike won't have the same effect in current mode as the current shunt acts as the short, don't see the point of a MOV shorting out a current shunt.
So true , normally MOVs are bidirectional and non-linear surge suppressing components. As such , they are normally used for limiting voltage during a surge or transient.
El multimetro owon BT41T es de 20000 cuentas 2pilas doble A consume 3mah y es muy rápido VERY FAST. Para los que utilizan por mucho tiempo el multimetro interfaz Android
Warren, about a simple way to check AC+DC mode: use a transformer (sinusoidal 60Hz) or any square wave output (as some Aneng have) and a 1.5V battery. Join negatives and isolate / “sum” the two voltage sources (AC and DC) joining their positive (in parallel), where each positive has a 47R resistor in series before joining them. It should give you a simple way to have an uncalibrated, but practical, AC+DC source to check this feature.
Me gustaría saber si la respuesta de este sz-20 es rápida sobre todo de infinito a cero ohms y saber cuánta corriente consume para saber la duración de las pilas. Según dicen que es lento
Hello Darren. Hmm .... 0660 processor in this level of a multimeter, of course, does not look very nice. Although the protection is performed on CAT III. Completely agree with the assessment. The multimeter is good, but there are places where for this amount they could try better. Still, HOLD PEAK is hard to beat. Under the last video, I asked for a review on such an accurate multimeter, only from another company, but this is its complete analogue, the same OEM. Thanks Darren. You are the best.
wow.. 25k counts! Bargraph, dual display and those other pros.. Aneng is definitely steal the spotlight. 👍 Agree about the LCD, i like the Zotek has than Aneng. Man, HT118A is having a hard time this year. 😅
The Venlab is killer. I think it's by far the best bang for buck meter you can get right now. I haven't had any discrepancies whatsoever with it against the shop Fluke so far. It's particularly great at measuring capacitance, which I find most multimeters fail at when and if they even have that feature.
Para los que utilizan por mucho tiempo el multimetro.Recomiendo el Owon BT41T+ consume 3mah 2pilas AA Muy rápido VERY FAST 20000 cuentas ademas interfaz Android
On AliX, everything from $52/Cdn/free ship to $84/$27 ship/ WTF? They play games with the shipping a lot these days. But the delivery date is nearly the same. Always check the total price. I do like Aneng but already have a UT-61e+ and a Klein MM700..... As Dave Jones says, you can't have too many DMMs (HP 1740A repair). But I think I'll wait.
Hey Barry. Yup. Ali is dodgy when it comes to shipping. Different vendors and different shipping rates. Sometimes cheapest shipping is a bad option. The ANENG arrived quickly so it was worth the $. Luck always plays a role too.. Agreed, more multimeters the better but then after a few hundred you kind of lose count 🤔👍
I think you would love this ANENG ! It's quite capable and that high resolution makes it even better. 👍
Год назад+3
Dzień dobry z Polski! Szczęśliwy użytkownik ANENG AN870 :) Could you check the speed of the bar graph in the next reviews? It should be much faster than digital reading.
Yes my friend , i usually make it a point to verify the speed and accuracy of the bargraphs. I did compare the bargraph of the ANENG and Zotek in this review aa well👍
I came for the multimeter and I stayed and subscribed for your content, edition, explanation... Amazing Do you still prefer the HT118E for the cheap-o?
That's great to hear !! Welcome my friend!! Yes, I do very much like the HT118E, all around I think it's still the best in the CHEAP-O Multimeter Realm! That being said, I also love my manual ranging Zotek ZT-980 and the new ANENG SZ20 is definitely not far behind! 😊
So finally a good protected cheaper millimeter, you can use with high voltage + high amps, because that protection is not on many cheap multimeters, and i can buy the ANENG SZ20 for €41,66 ($45.26 usd) on AE, and that is with 15-day delivery and Free Shipping (EU).
Well now - Aneng is finally stepping up their game for real with some meaningful improvements and additions. Now if they want to keep the price same or lower and add a more vivid display, divorce the backlight from the flashlight and make the mA range 500 to 600 mA this one could be a real keeper as it seems to perform nicely otherwise, but price is a tad high. 25,000 count dual display is a real standout for Aneng, heres hoping for this one to blossom in the future.
Blossom would be good! That input protection really poked me in the right place, definitely was not expecting this from ANENG. 😃
Thanks for showing the difference with the displays
Great review as usual, thanks a bunch. I must say I was waiting for this one, seems like an interesting new product from Aneng.
Thx André ! It was definitely worth the wait.! All around a solid package that should keep most users extremely satisfied 😊👍
I bought one (38 US$) and I am very satisfied with the multimeter. Now I'm looking forward to receiving the next one I bought, an Aneng ST212!
Awesome sauce ! It's absolutely a great multimeter 😊
Usually I’m not a fan of Aneng multimeters, but this one is all right. Decent accuracy, nice ranges (except for mA), better than usual input protection, good resolution, dual display is always nice to have. The bar graph doesn’t seem that fast though, but hey, at least it’s there. 👍
You’re right, $54 is a little too pricey for that. In this price range I would personally go for Uni-t just because their overall quality is more consistent, or wait for this one to go on sale.
I have a feeling the price will drop on this ANENG fairly quickly. Definitely one of their better offerings as of late.
25000 count for the money is really good. On a side note, I have to say your b roll footage is amazing. Nice job as always my friend. 👍👍
Thx my friend! Agreed, those Xtra counts are definitely appreciated in the CHEAP-O zone.
Glad you like the b rolls ! 😊
Interesting input protection concept. The MOVs are usually on the voltage input as that is the mode that the meter will suffer from voltage spikes. Voltage spike won't have the same effect in current mode as the current shunt acts as the short, don't see the point of a MOV shorting out a current shunt.
So true , normally MOVs are bidirectional and non-linear surge suppressing components. As such , they are normally used for limiting voltage during a surge or transient.
El multimetro owon BT41T es de 20000 cuentas 2pilas doble A consume 3mah y es muy rápido VERY FAST. Para los que utilizan por mucho tiempo el multimetro interfaz Android
Warren, about a simple way to check AC+DC mode: use a transformer (sinusoidal 60Hz) or any square wave output (as some Aneng have) and a 1.5V battery. Join negatives and isolate / “sum” the two voltage sources (AC and DC) joining their positive (in parallel), where each positive has a 47R resistor in series before joining them. It should give you a simple way to have an uncalibrated, but practical, AC+DC source to check this feature.
Great 👍 advice !
Me gustaría saber si la respuesta de este sz-20 es rápida sobre todo de infinito a cero ohms y saber cuánta corriente consume para saber la duración de las pilas. Según dicen que es lento
Amigo ve mi comentario OWON BT41T+ VERY GOOD
Darren one question… zotek, aneng, and kaiweets even habotest are suspicius similar are this brand the same company?
Hello my friend! Zotek is usually the OEM for Aneng, HABOTEST is the OEM for Kaiweets although they may have some firmware differences. 👍
Hello Darren.
Hmm .... 0660 processor in this level of a multimeter, of course, does not look very nice. Although the protection is performed on CAT III. Completely agree with the assessment. The multimeter is good, but there are places where for this amount they could try better. Still, HOLD PEAK is hard to beat.
Under the last video, I asked for a review on such an accurate multimeter, only from another company, but this is its complete analogue, the same OEM.
Thanks Darren. You are the best.
Aww shucks, u- r- d best my friend 😊 LOMVUM is coming this month too!
Thanks for the review.
Cheers José !
I like the resolution but The HT118E is really hard to beat. Great video Darren. 👍👍👍
Thx my friend!! 118E is definitely awesome!😊
Buen día alguien sabe cuanta corriente consume..(se mide en serie con las 3 pilas) y saber si es rápido. Gracias.
wow.. 25k counts! Bargraph, dual display and those other pros.. Aneng is definitely steal the spotlight. 👍
Agree about the LCD, i like the Zotek has than Aneng.
Man, HT118A is having a hard time this year. 😅
I'm telling ya...lots of great new meters and its only April !!😅
@@KeepOnTesting yes... soooooo exciting 🤩
Not bad at all. I just got the Venlab you showed a week ago. When this gets a little cheaper I'll get it.
Hi Tron, How are you liking the Venlab so far..?
Price should drop on the ANENG soon..
The Venlab is killer. I think it's by far the best bang for buck meter you can get right now. I haven't had any discrepancies whatsoever with it against the shop Fluke so far. It's particularly great at measuring capacitance, which I find most multimeters fail at when and if they even have that feature.
Para los que utilizan por mucho tiempo el multimetro.Recomiendo el Owon BT41T+ consume 3mah 2pilas AA Muy rápido VERY FAST 20000 cuentas ademas interfaz Android
I agree Jose, the OWON is a fantastic multimeter with lots of functionality 👍
Sir please show frequency parameter of various multimeter to check drives of power supply.thanks
On AliX, everything from $52/Cdn/free ship to $84/$27 ship/ WTF? They play games with the shipping a lot these days. But the delivery date is nearly the same. Always check the total price.
I do like Aneng but already have a UT-61e+ and a Klein MM700..... As Dave Jones says, you can't have too many DMMs (HP 1740A repair). But I think I'll wait.
Hey Barry.
Yup. Ali is dodgy when it comes to shipping.
Different vendors and different shipping rates. Sometimes cheapest shipping is a bad option. The ANENG arrived quickly so it was worth the $. Luck always plays a role too.. Agreed, more multimeters the better but then after a few hundred you kind of lose count
🤔👍
I've been watching this video many times. It kinda make me want to purchase. I don't know if aneng sz20 or zotek zt-980 is better.
I think you would love this ANENG ! It's quite capable and that high resolution makes it even better. 👍
Dzień dobry z Polski!
Szczęśliwy użytkownik ANENG AN870 :)
Could you check the speed of the bar graph in the next reviews? It should be much faster than digital reading.
Yes my friend , i usually make it a point to verify the speed and accuracy of the bargraphs. I did compare the bargraph of the ANENG and Zotek in this review aa well👍
I ordered one of these, the temp probe came in a metal tube. I cooked steak with it last week
Now you're talking.. a multimeter that can dish out a nice medium rare!
Does aneng has acceptable and accurate multimeters although I should test them to
I came for the multimeter and I stayed and subscribed for your content, edition, explanation... Amazing
Do you still prefer the HT118E for the cheap-o?
That's great to hear !! Welcome my friend!! Yes, I do very much like the HT118E, all around I think it's still the best in the CHEAP-O Multimeter Realm! That being said, I also love my manual ranging Zotek ZT-980 and the new ANENG SZ20 is definitely not far behind! 😊
@@KeepOnTesting Thanks for the help. By the way, did you ever have the chance to try the Zt-702s?
@@harduino Zotek shipped it to me last week but it was supposed to ship a month earlier. 😃 The review will go live in June ! 👍
@@KeepOnTesting I am looking foward for this one. Keep the amazing work and effort
How about a comparison between aneng zs20 and kaiweets ht118E?
Even though aneng is supposed to have 5000 counts more resolution!
Interesting..
Ok on my list.. 😊
Nice review.😊
Glad you liked it
Nice. The build is so close to the zotek I wonder who the oem on the two is.
That's a great question..!
Why refresh speeds are so bad? it performs as my 40 year old Keithley DMM :D
Interesting.
I found the refresh rate very good. The higher resolution will make it a tad slower in the lower ranges but it's negligible.
@@KeepOnTesting Check Amprobe PM55 for example, for really good refresh rate (in portable DMM of course).
DC amp clamps ? got the multi meter i want from you just waiting for amp clamp please
Clamps a comin!
@@KeepOnTesting Thankyou
I like the Klein CL390.
@@barrybogart5436 Thankyou will give it a look
How does it reads on 4 to 20 mA ?
Like a champ...no worries there !
Cool I want it. Somebody can share URL with sale for buy this Aneng sz20?
is this the same as the zotek zt225?
Yes, Zotek is the actual OEM.
I like this but that more 😁 .... It was zotek😊
What is the best multimeter brand?
Fluke
Qual nome da musica
Musica is in description 😊
Parabéns pelo vídeo 😊😊😊🎉🎉🎉 de Brasil
🌟💯👍🏻👍🏻👍🏻❤️👍🏻👍🏻👍🏻
😊👍
Is this sponsored ??
Whaaaaaat? No its not sponsored, Why in the world ??
This or Kaiweets HT118e if they are the same price in July 2024? Thanks
So finally a good protected cheaper millimeter, you can use with high voltage + high amps, because that protection is
not on many cheap multimeters, and i can buy the ANENG SZ20 for €41,66 ($45.26 usd) on AE, and that is with 15-day
delivery and Free Shipping (EU).
That's a great deal with the free shipping! Nice to see ANENG step up with the input protection 👍
@@KeepOnTesting Yeah i hope the rest is also going to do that.