2007 ford expedition 5.4 triton radiator removal

Поделиться
HTML-код
  • Опубликовано: 6 окт 2024
  • Radiator Removal

Комментарии • 48

  • @m3bimmer89
    @m3bimmer89 4 года назад +10

    Just replaced the radiator in my 08 Expo today.....had been putting off for some time due to the removal of all the parts/pieces in the way of the radiator itself.....your video was very informative and help me quite a bit......complete job took approximately 4 hours from start to end.....Thanks my friend

    • @chicopimp
      @chicopimp  3 года назад +1

      You are very welcome

  • @ericseckman6138
    @ericseckman6138 3 года назад +5

    Thank you, this is the most rediculos radiator replacement is ever done. Your video helped me to keep my sanity (lol)
    I appreciate your work thank you.
    I don't know what the shop flat rate you be but it would probably cost anywhere from $600.00 to $850.00 easy

  • @davidgallo5676
    @davidgallo5676 4 года назад +7

    Great video. It's the only one out there so thanks. Minor suggestion. I did not have to remove the headlights, air intake box, or the coolant reservoir. Everything else I did though. Also, the fan shroud comes off super easy once you figure out that the bottom of the shroud has a hinge on it that very easily allows the fan shroud to come out. Thanks again.

    • @bepolite2
      @bepolite2 3 года назад +1

      So, how you removed the transmission fluid hoses that are connected from the front?

    • @chicopimp
      @chicopimp  3 года назад

      I am glad you were able to find ways to cut the time, if I had something to go by I probably would have done less lol.

  • @sidney.williams
    @sidney.williams 5 лет назад +6

    also, helps to spray lube onto grill at bottom to easily remove plastic tabs from bumper cover.
    I used penetrating oil and a painters knife. before the oil it was impossible for me to just get the grill off. from there, your instructions were spot on!. Thanks again.

    • @chicopimp
      @chicopimp  3 года назад

      Thanks for the input and you are very welcome

  • @michaeltaylor7822
    @michaeltaylor7822 3 года назад +2

    Great job sharing all the minute details. The only issue I had was the fan shroud. Everything else was simple following your directions. Many thanks.

    • @chicopimp
      @chicopimp  3 года назад

      You are very welcome

  • @sidney.williams
    @sidney.williams 5 лет назад +4

    Very nice of you to lend your time for this. Thanks

  • @outcomeagent53
    @outcomeagent53 4 года назад +3

    I have the same exact vehicle! Thank you for the vid. It’s my Labor Day weekend project

    • @chicopimp
      @chicopimp  3 года назад

      You are very welcome

  • @heinzdoofenshmirtz3783
    @heinzdoofenshmirtz3783 Год назад

    thanks a ton man, all the other videos required more steps and people that didn’t really know what they’re doing. i’m gonna be doing this job with my dad in a few days on my 2009

  • @MrMattuse
    @MrMattuse 4 года назад +3

    Outstanding brother. Thank you.

  • @dude12348
    @dude12348 4 года назад +2

    thank you so much. extraordinary detail!

  • @sincitywelding8694
    @sincitywelding8694 4 года назад +2

    Great video! Goin out to the garage today to get her done lol!

  • @leroijr407
    @leroijr407 4 года назад +2

    Thank you. Great video. Much help...

  • @30Thousand
    @30Thousand 4 года назад +2

    Thanks for the details!!!!

  • @quadzilla-qu3ch
    @quadzilla-qu3ch 2 года назад

    Good video Carlos, thanks a lot

  • @bossman1962
    @bossman1962 5 лет назад +3

    Ur the champ

  • @juanpowet5543
    @juanpowet5543 3 года назад

    Hey Carlos you are the best👍

  • @richardcard9328
    @richardcard9328 4 года назад +2

    Damn bro is it really that hard and how long does it take you? I was thinking about doing it myself because the dealer wants 1000 bucks.

    • @chicopimp
      @chicopimp  3 года назад

      Sorry that now is when I reply to you. The projects always seem bigger than what they are until you start doing it and when you have some type of guidance you're always going to find ways to do it easier lol.

  • @masscomnet
    @masscomnet 3 года назад +1

    Great video. What a crap design. A radiator replacement on my BMW takes about 20 minutes total.

  • @RandomJ2023
    @RandomJ2023 4 года назад +2

    OMG all that for my radiator I am scared

  • @yello4543
    @yello4543 5 лет назад +2

    On the lower radiator hose is there a specific way to remove it?? Any special tools...

    • @sidney.williams
      @sidney.williams 5 лет назад +1

      pushes off with small flathead from each side

    • @28764651
      @28764651 4 года назад

      Why didnt you show video while u were doing it? Video was still helpful though.

    • @nathanielsteve2932
      @nathanielsteve2932 2 года назад

      If it's a quick connect you have to remove a clip it's easy to remove with a small screwdriver then just wiggle an pull at the same time .. it should pop off ... Gud luck hope it helped

    • @gmooney57
      @gmooney57 4 месяца назад

      I used some big channel locks and twisted clockwise and pulled at the same time. Aggravating but got it done.

  • @jdeuces1548
    @jdeuces1548 3 года назад

    Good video bro, how did u check and ad transmission fluid, my 2007 doesn't have a dipstick viable under hood, thank you

    • @chicopimp
      @chicopimp  3 года назад +1

      The dipstick is under the car above the transmission pan, I would be lying to you if I tell I checked it lol.

  • @nathanielsteve2932
    @nathanielsteve2932 2 года назад

    OMG .. you didn't have to remove all that .. some of what you removed you didn't have too...

  • @DragonPilot
    @DragonPilot 23 дня назад

    How the heck you remove those pesky shroud clips?

  • @BallisticThreatGainesvilleGA
    @BallisticThreatGainesvilleGA 2 года назад

    Had my radiator replaced a few months ago. I'm starting to see a slow leak of transmission fluid on the right side of radiator. Under power steering fluid and air filter area. Can anyone point to where the trans connects to radiator?

  • @christianruiz6846
    @christianruiz6846 3 года назад

    The radiator is the same for a Lincoln navegator 2007?

    • @chicopimp
      @chicopimp  3 года назад

      I don't know, sorry.

  • @lues7757
    @lues7757 4 года назад +1

    Half of the sh!t you removed didn't need to be removed.

    • @LiilTyweezy
      @LiilTyweezy 4 года назад

      u a lie u must never done this

    • @lues7757
      @lues7757 4 года назад

      @@LiilTyweezy Actually I've done it a few times.

    • @producedbydoeselo2293
      @producedbydoeselo2293 4 года назад

      @@lues7757 what don't j need to remove ? Mine is leaking

    • @lues7757
      @lues7757 4 года назад

      @@producedbydoeselo2293 I removed the grill the headlights the top piece of plastic and detached the top hoes and bottom hoes that has a c-clip on it including the small oil hose connected to it on the bottom, that's it then I wiggled it out of there.

    • @lues7757
      @lues7757 4 года назад

      @@producedbydoeselo2293 I might have removed a few sensor clips but i did not remove the air intake or the shroud or the coolant reservoir or the battery box, nothing else but what was actually holding it from coming out. after you remove what's holding it down you can wiggle it out and put the new one right in.