Truck engine assemble| full engine fitting| heavy vehicle Engine
HTML-код
- Опубликовано: 28 ноя 2021
- "diesel Engine assemble Process"
"diesel Engine assemble"
"truck engine"
"truck engine assemble after repair"
"indian truck"
"indian truck repair system"
"vehicle engine assemble"
"destroyed engine assemble"
"truck engine repair"
"truck engine rebuild"
"diesel Engine fixing"
"big vehicle engine assemble"
"giant engine assemble work"
"truck engine repair work"
"vehicle work shop"
"how to repair truck engine"
"how to repair diesel engine"
"tata truck engine assemble"
"tata truck engine"
#truckenginerebuild
#truck
#vehiclerepairwork Наука
One thing only really to say : Hats off for their dedication and commitment. Personally I would have relegated myself to be watching them toiling.
Походу у парней дорога любимое место для переборки мотора , работать весело много знакомых проезжает мимо, советы дают и если что помогут засунуть на место.
These guys just get it done no excuses well done
you should go work with them
I wouldn't say well done! You NEVER put main bearings in dry, same with rod bearings. They put the main bearing caps on without lube on the bearings, which will cause premature bearing failure, not to mention they never followed a torque sequence for the crankshaft. You NEVER tighten any bolts from the ends first, always start in the middle & work out! That goes for crankshaft, heads, valve covers & oil pan!
Sure they got the job done, but it was NOT "well done"!
@@timothygeiger8271 he wiped oil on the bottom bearing 😶
@@ronalddaub7965 you need more than just the bottom bearing done, besides on a rebuild it's best to use assembly lube, it stays on the bearings, & you never want a dry initial start-up after an overhaul.
Oil is good after the engine is running, but its best to use a lubricant that sticks to surfaces for initial start-up, after an engine has been rebuilt.
They didn't torque anything, which isn't good either.
They may not have access to all the lubricant you have , but likely there skill and bad habits have been handed down , there no school to go to , you start working as a young kid for you father and grandfather.
Who says you can't rebuild your engine on side of the road?
🤣🤣🤣
⁸
Only the people from america and europe, because they are rich asf so they have garages for that
@@allenvictor6114 the that
Even showroom people sends the vehicles that they can't get repaired perfectly to a roadside workshops for very less cost and showroom people charges very huge amount to the customers.
There is nothing amazing like Mechanical work specially Engine rebuild 🙏
It's like giving a new life to dead engine
Curing a sick machine
Just like doctors
They do it on human and mechanical workers are doing it on machine.
All on side of the road on a tyre.......amazing..
Мне вот интересно, у них в ПТС, в графе цвет, что написано? "нарядный", "красивый"..?))
Here in the UK, you can't work on anything outside until summer 😂.
Very lucky to have nice weather all year round. Great video. 👍
Yes now look like lucky 😂 but summer you can't manege here 48°C so in summer you are lucky
@@UniqueThings18 great comment 👍 👌
Well din ooo
you should go work with them
This comment didn't age too well
Nice rebuild. That engine was probably from 1992 and has 2 million kms
I admire this people...it's an inspiration
You guys are totally amazing. Hats of to the mechanic an his assistant. 👍
you should go work with them
@@roverwaters3875 what tf were u thinking when replying with this? 🤣
You think that was amazing? They slapped that engine together without regards to cleanliness, they never lubricated the crankshaft main bearings, or the rod bearings, they didn't torque the main bearing caps, or the rod bearings. That engine is going to fail prematurely because it was assembled without lubrication, & was never torqued.
An overhaul on a truck engine takes a good mechanic close to a week, when its done CORRECT! These guys cut so many corners, they didn't lubricate anything going back together, then the tightening sequence on the main caps was just horrible! Never work from the ends, always tighten from the middle out & torque the bolts! Who knows how long that engine will last, but you can bet on one thing, it will be a miracle if it lasts longer than a year or two.
@@roverwaters3875 😂😂
Nut bolts uneven tight hue hai pnumatic spanner se karna chahiye equally fit karta hai sab 😐
Makes me feel a lot better about my own engine rebuild... 😳😊
Yea its a very dirty rebuild
@@charliemclaughlin1042 not to mention, *without a torque wrench* lol
Love seeing videos like this
You don't need all the Fancy things
All you need is knowledge And ability to work
lqa
q in
Помыть колена в ржавой бадье, равнозначно полировке.
Watching these videos make me want to work on stuff now .
Wow easy on that camshaft 🤣
Excelente trabajo y video gracias por compartir tu gran experiencia desde costa rica Maestro excelente
These gentlemen are the real life MacGyvers. I am very impressed.
Me too . they have an
Answer to anything.
And just keep moving forward.
One day somehow someway i wanna buy all these guys wearing sandals a new pair of quality Red Wing boots🥾
Aa
@@siatunsupriono7158 n
Ko in
And they will sell them by end of day for buying local booze ☠
Job well done 👍 . FANTASTIC.
These guys are pros. They know every specific torque spec for each bolt. And can do it by hand. 😂😂
Vocês são excelentes no que faz! profissionais e não trocador de peças! Parabéns.
Lè degaman moteur dti international bay anpil lafimin kikoz
My respects to the guys awesome work
Bom trabalho amigo parabéns
It's a 5.9 cummins so they can rebuild it under thar desert sand & it will still run another 100000km 😂
Sure, sure....
Tata engine
कमसे कम साफ सफाई का तो ध्यान रखो
@@maheshnambidi tata make only chassis bro engine is from another brand called cummins gearbox usually in tata is of brand named zf and even the new bogie type suspension in newly launched mining tipper of tata comes from hendrickson
@@nikhilmishra1081 yes. Unfortunately Indian companies are not competent for the same.
Can't help but wonder how many times they end up rebuilding the same engine because they're assembling it in a sandbox you know they go through a lot of bearings
The best way of ensuring the customer soon returning for yet another rebuild !
sand 🤣
Está mal ese lugar para ese trabajo no quedará bien el motor
That's going to be 30 rupees please!!!!!!! Thank you come again........ LoL LoL LoL 😂
svaka cast kapa dole ovo su majstori
Они сняли и разобрали двигатель для того , чтобы помыть его изнутри ? Ну ладно бы так, так и помыли же плохо...
dobra robota panowie !
Savages straight savages!
Very hard work without any power tools great
Good job !
I always wonder how many bearing surfaces get contaminated from building engines in the dirt and dust
It is old, low HP per liter engine - it will work fine. However try to do it with the modern one - it will be destroyed in no time.
It's not enough to matter on a bearing that size.
The kid supporting the radiator hose was the real unsung hero that day.
Nice job 👍🏼 . Old timers👽
Great job
Os.senhores.sao.uns.verdadeiros.mestres.da.mecanica.diesel.forte.abraco.desde.o.brasil.
Respect! With the Lots of Sand on the floor
Amazing work 👍
че потрясного? в говне собрали двс , в писке, без моментов крутят, распред вал просто забросил в блок. Те кто считает такой ремонт гениальностью в авто технике полные олени))))))
Best work out there lol .
WOW amazing skill
1000 bravo boncourag 👍👍👍👍👍💪💪💪💪🏆🏆🏆🏆
MUY BUENOS MAESTROS ...A
LA ANTIGUA EN EL SUELO ..FELICITACIONES DESDE 🇨🇱...PAQUISTANIESBUENOS PARA TRABAJAR....UNO PARA TODOS TODOS PARA UNO....🇵🇰🙋👍👍👍✌
A. M. A. Z. I. N. G
GOOD PEOPLE
SMART PEOPLE
NICE PEOPLE
GOOD JOB
SMART JOB
NICE JOB
GOD BLESS
THE BEST
Thee guys re so good t their work.
Dirt is really good for the motor
It's good for business...🤣😂🤣😁😁😁😁👍🏽
Job security
Tough Men!!
God Bless You All!!
Amen!💚🍀🌼🌼🌼🌼🍀🍀🍀🍀💚💚💚💚💚💚💚
When the revolution comes i want these guys on my team.
Very nice
What a professionalism! 😀 look the first part of the video
Bekerja dengan team yang sangat kompak
NO BRASIL QUALQUER MECÂNICA PRA FAZER 1 MOTOR FAZ A MAIOR NOVELA METE A FACA AINDA NAO FICA BOM ..ESSE POVO ALEM DE NAO TER RECURSOS DAO UM SHOW DE MONTAGEM E HABILIDADE PARABÉNS PELO VÍDEO
Wow wow 👍👍🇲🇽🇲🇽 perfec 👍
Красавчики,Уважуха .
Good job sir idol pasout po thank you
I really wanted to see when the Engine starts
Every single one of these videos I watch there's always some smart person who bangs on about how dirty the working conditions are and how the bearings will be destroyed. Cmon that guy, give it a rest, it's not your struck and it'll be fine anyway, those bearings are huge so a little bit of dust or grit ain't gonna do much damage.
Хорошо помыли двигатель.
Esse tipo de trabalho também se faz no Brasil.Perto de minha casa há três oficinas que fazem isso.Inclusive refticam o crankshaft.
Passa óleo na dedada também?
Video plz
Good job 👍
That same rag cleans up parts and for holding wrenches too😌
Absolutely no chance of sand or dirt in the motor...very clean assembly..
Did they spray paint the top of the pistons??
Nice
Realmente o verdadeiro mecânico beira de estrada..sistema bruto que resolve...like do Brasil.
sim, nós somos assim ✊
Brasil 🤏🤢
World class “mechanics”
Job done
By- pass way no torque wrench, that's the only way when your in middle east, it's in Pakistan, engine won't last long.
India
Com muito cuidado deu certo
Parabéns quem sabe fãs ao vivo proficionalismo em Alto nível eu do Brasil desejo que deus derrame toda há sorte de bênçãos sobre a vida de todos dessa nasaoa maravilhoza
"Quick speedy service, drive in- drive out"
Respekt Bruder stabil
Veri naes
Tail light warranty.
Once the Tailights are gone, so is the warranty.
Good
I'd love to have the knowledge to do this even on a car lol
I'd like to know better 😉👍
отчаянные парни
Love the torque wrentch. CLICK.
Work with the ft manual
С песочком лучше притрется 😁
Good for another 100,000…feet that is
Il va être beau le plan de joint de culasse du bloc posé sur une roue direct !
Adimiro a raça desses caras
it’s scary they don’t torque anything to specifications. important step to rebuilding an engine.
@@madlad8629 wrong
Pra apertar os parafusos não são chaves com a pressão certa ?
Bearing lubricating ?????????
Они хотя бы один час дают гарантию?
Cool
Looks like a drive through engine rebuild garage. Would you like fries with that?
Lol put thr bolts tight as you can and wish for the best
As much as I cringe on their practices, I ACCEPT AND RESPECT the talent and making the best of what they have.
Bhai wah mamu nadeem bol Raha hoo Delhi darwaza wala from Saudi
Not one Snap On tool to be seen 😂
Insane but I guess it may work too
👍👍👍👍👍
I noticed he was not using the assembly lube on the crank bearings. Dry start up. That’s not good
Песок и пыль- есть смазка))))
Putting in the bearings for the pistons and the crank shaft has to be done on a clean area. They are in a very dusty, sandy area. Wiping stuff with a old dirty rag.
@@madlad8629 The problem is that's not the way to do it get organized get a clean fucking environment there's nothing to brag about here there's nothing to be proud of here this is a fucking hack job
Всем привет. надеюсь меня услышат ребята которые ремонтируют данный мотор да и другие тоже. Вот на видео четко видно износы вкладышей поршневой группы, втулок распредвала и так далее. Скажите мне а в чем смысл ремонта? Что бы через 50 тысяч км достать мотор снова и опять делать простите меня обезьянью работу??!!! Раз нашли и поменяли коренные вкладыши почему не поменяли шатунные и распредвала. Физика такая что теперь на колено будет еще меньше смазки приходить так как давление больше будет там где больше зазор а значит что не колено будет смазыватся а распредвал. Смысл ремонта???
Какой ты не понятливый . Они сняли мотор что бы помыть и то это сделали плохо .
Q difícil esse trabalho de vcs
Vcs trabalham com pouco recurso
Nel sud Italia lavorano anche così
min 5:03 gran torque de apriete por detras aunque seria mejor sin el jean
I watched in amazement. However, no torque wrench. That engine will not last long at all
This engine's already 150 hp with a 650 nm torque Cummins engine. For a big 10 wheeler, it must have a torque of 1000 nm for good performance.