Update: By the third charge on new batteries, with topping off the full batteries-just before flight and being real gentle flight times are just short of 17 minutes for stock. I like the camera upgrade, battery and antenna, I do wonder if a FLIR camera is available??? or two cameras, adding a four bladed main would increase lift and efficiency but shorten the main drive system by 50%
Very Clever brother, you made it seem simple I was thinking "why didn't I think of this?". Believe it or not, DJI's silent propeller is compatible with the rotorhead assembly of this toy(with some micro drilling ofcourse).
Hi, which version of silent DJI? FYI: in the E110 directions the screw set of the main rotors is to be loose or the copter will shake, on this design the main folds. On a different thought has anyone thought to skeletonize the air frame to reduce weight? Does the "cargo" lift capacity increase with a four bladed main? 3D printing might be a thing to look at.. Add a FLIR camera, add wing lift like the Hind E has.
@@frickandfracksicem that sounds like a pretty good idea if you have a 3D printer give me an update as soon as you 3D print the frame as far as in the night vision I'm sure that'll be pretty expensive my main goal is to get a flight controller small enough to go inside this copter to fly like a toy copter but as powerful as a full-blown 3d copter 👍
Nice work! Would you be able to higher the voltage aswell when you change the battery, or does more need to be replaced for that? More voltage opens alot more 5.8 GHZ FPV cams
Actually you cannot unless you put a whole new flight controller board on the helicopter it only take 3.7v you could double the capacity of 3.7v but don't know if the motor will be able to lift the helicopter 🤔 I hope this helps
Love this creativity, FYI: You see the profile picture to the left? do you see? really? Back to this channel, what brand camera did you use to upgrade? Have you tested the "lift" for cargo?
Hey man doing some basic flying at about 5600 ft above sea level i am getting about 13-15 minutes of flight and maybe a minute or 3 less if i push it a lot. (fully stock)
@THOMAS EVANS fully stock kit but after a year of use i will probably return to your video give an update of rough cycles and flight time and also do the natyery upgrade you did. (I got 3 batteries) so if it can increase my flight time to 20 minutes I can basically fly uninterrupted
I do believe the weight of the battery is too heavy I have not tried it but the weight is double the weigh of the battery I did weigh both of those side by side , and the 18650 battery weighs about 23 g
Update: By the third charge on new batteries, with topping off the full batteries-just before flight and being real gentle flight times are just short of 17 minutes for stock.
I like the camera upgrade, battery and antenna, I do wonder if a FLIR camera is available??? or two cameras, adding a four bladed main would increase lift and efficiency but shorten the main drive system by 50%
I like the upgrades, bought one because of your work, nice popup and SEE what is happening, none the wiser.
Thank you I appreciate it this is a very fun little helicopter really opens up the imagination of an expensive stealth and spy drone.
Very Clever brother, you made it seem simple I was thinking "why didn't I think of this?".
Believe it or not, DJI's silent propeller is compatible with the rotorhead assembly of this toy(with some micro drilling ofcourse).
Cool send me details, and I'll be putting up more hacks and ideas,,do me the honor of subscribing 👍 Thanks Brother
Hi, which version of silent DJI? FYI: in the E110 directions the screw set of the main rotors is to be loose or the copter will shake, on this design the main folds.
On a different thought has anyone thought to skeletonize the air frame to reduce weight?
Does the "cargo" lift capacity increase with a four bladed main?
3D printing might be a thing to look at..
Add a FLIR camera, add wing lift like the Hind E has.
@@frickandfracksicem that sounds like a pretty good idea if you have a 3D printer give me an update as soon as you 3D print the frame as far as in the night vision I'm sure that'll be pretty expensive my main goal is to get a flight controller small enough to go inside this copter to fly like a toy copter but as powerful as a full-blown 3d copter 👍
Nice work! Would you be able to higher the voltage aswell when you change the battery, or does more need to be replaced for that? More voltage opens alot more 5.8 GHZ FPV cams
Actually you cannot unless you put a whole new flight controller board on the helicopter it only take 3.7v you could double the capacity of 3.7v but don't know if the motor will be able to lift the helicopter 🤔 I hope this helps
Love this creativity, FYI: You see the profile picture to the left? do you see? really?
Back to this channel, what brand camera did you use to upgrade?
Have you tested the "lift" for cargo?
I use the end all in one camera and extended the antenna wire camera was only 20 bucks on Amazon
Hey man doing some basic flying at about 5600 ft above sea level i am getting about 13-15 minutes of flight and maybe a minute or 3 less if i push it a lot. (fully stock)
That's pretty good what batteries are you using
@THOMAS EVANS fully stock kit but after a year of use i will probably return to your video give an update of rough cycles and flight time and also do the natyery upgrade you did. (I got 3 batteries) so if it can increase my flight time to 20 minutes I can basically fly uninterrupted
ruclips.net/user/shortszm6VDSyGZr8?feature=share how to hook up camera power
Hello, nice work. Did you see this mod - ruclips.net/video/mRQKog7m83s/видео.html Probably all videos from this author can be interesting for you.
Can it handle 1S 18650 (eg. VTC6 30A 3000mAh, approx. 45 g) ?
I do believe the weight of the battery is too heavy I have not tried it but the weight is double the weigh of the battery I did weigh both of those side by side , and the 18650 battery weighs about 23 g
maybe? if you're willing to ditch the plastic canopy & run the copter bare electronics only.