How to install an ATI Super Damper on a Corvette (C5 1997-2004) [Harmonic Balancer install]
HTML-код
- Опубликовано: 21 янв 2021
- Today I'll show you how to install a new ATI Super Damper on your C5 Corvette!
Harmonic Balancer Removal Steps - Corvette only [C5 1997-2004]
1. Removing Alternator - • How to remove an Alter...
2. Removing Front Sway Bar - • How to remove a front ...
3. Removing Steering Rack - • How to remove a steeri...
4. Removing Crankshaft bolt and Harmonic Balancer - • How to remove cranksha...
5. (This video) Installing Harmonic Balancer - • How to install an ATI ...
Tools:
Extended harmonic balancer kit
27mm socket
250lb torque wrench
🏎🏎 Arctic Vette's Home 🏎🏎
www.arcticvette.com
🙏🏼🙏🏼 Thanks for watching! 🙏🏼🙏🏼
Be sure to subscribe for future uploads! Drop a comment below and smash the thumbs up if you enjoyed the video!
☕️🚗 Hutchinson Cars & Coffee 🚗☕️
/ carsandcoffeehutchinson
🚨Next Cars & Coffee Event 🚨
TBD in 2021
Tom and Dan's Tire Service
710 S. Main South Hutchinson KS
💈💈 Arctic Vette Store 💈💈
teespring.com/stores/arctic-v...
🤍🤍 Support via Patreon 🤍🤍
/ arcticvette
🤍🤍 Support via PayPal 🤍🤍
www.paypal.me/GriffinTA
📸📸 Instagram 📸📸
/ arcticvette
🖥🖥 Twitch 🖥🖥
/ arcticvette
📘📘Facebook📘📘
/ arcticvette
🦅🦅 Twitter 🦅🦅
/ arcticvette
📕📕Tumblr📕📕
/ thearcticvette
📝📝Reddit 📝📝
/ arcticvette
💰💰 Discounts 💰💰
Use Code ArcticVette
10% off Vette-Lights www.vette-lights.com/
🎸🎸 Song 🎸🎸
Living Life by Dawson
/ living-life My GEAR: (Amazon Affiliate Links, may earn commission)
GoPro Hero 9 Black: amzn.to/3Kv1Mob
GoPro Hero 9/10 Media Mod: amzn.to/3rFtYMO
GoPro Handler: amzn.to/3nG33PD
GoPro Accessory Pack: amzn.to/3IBMzjJ
32gb SD Card (2 pack): amzn.to/3GX0pfK
GoPro Charger & Extra Battery: amzn.to/3tXPAqv
RODE MIC: amzn.to/33O1J67 - Авто/Мото
I ended up using some thin rope and looped it through the balancer itself and tied it super tight onto the car itself to stop the crank from spinning while tightening the bolt on the new balancer I didn’t wanna risk using a pry bar or screw driver to wedge in.
That's a great idea! Thanks for sharing your method with us 🙏🏻
Why did you use gasket maker on the keyed groove? I have a 2000 C5 that’s gonna need a damper pretty soon.
I did that because my crank isn't keyed. It's best to put some high temp gasket maker in place of where the key should be in this situation. However yours maybe keyed and in that case you wouldn't apply any gasket maker to the balancer.
Good luck with yours! I've got videos on every step to getting to this point in my Avy the Corvette playlist.
@@ArcticVette thank you buddy I appreciate it ♥️
@@zunySSBM you're welcome!
How did you torque the bolt without the crank turning ?
Used a pry bar to hold it in place, same as removing the bolt. The crossmember was helpful here
What’s the part number for the one you used
ATI-917266 is the Balancer
ARP-234-2503 is the bolt
I see a lot of different ones on here is yours the base or the zo6 mine is the base
Mines a base model