How to use slip couplings to tee into a rigid copper pipe
HTML-код
- Опубликовано: 20 авг 2024
- In this video I use two slip couplings to tee into a rigid copper pipe. Slip couplings are useful for joining into any rigid copper pipe as they allow a new fitting or piece of pipe to be inserted into a pipe which cannot be moved. The fittings used in this video are solder ring fittings, which already have the solder built into them.
At last someone who is able to do the job and teach people how to do it, brilliant.
Thanks for the comment 👍
Okay . . . this may be one of the BEST plumbing videos out there. I never would have figured this out on my own. So that's what the slip joints are for!!
Thanks for the comment 👍
Great video at a great time. I have been struggling with this for weeks now as I didn't know 'Slip Couplings' existed. You're going to save me hours over the next couple of months (upgrading and adding radiators on a single pipe system). Many thanks.
You are welcome
Thanks for the comment
As a home DIY, I had the same challenge and it's been bothering for days. Could not figure out how I could achieve this. Then I saw your video... simple but so effective. Thanks so much.
Same here, I spent hrs trying to fit things wondering how ppl do it
We are just out of lockdown Covid' 19
and need 22mm trench rad' connected in my new extension.
Lazy plumbers around here!!
I used to fit complete kitchens.
After watching that l now have the knowledge to connect to existing so I'm draining down & getting a pipe bender and now can connect up to the house heating system & do it myself!
Thankyou so much!!
You are welcome. I'm glad you are out of lockdown!
Thanks for the comment
Another thing I never knew. Slip couplings would have saved me loads of work over previous years. Many thanks for this.
You are welcome ;-)
Thanks for the comment
All very clear and well done.. You could have used a single slip joint and the T instead of 2x slip fitting. Two less joints and one less fitting needed. Also I would suggest turning the pipe in the fitting to be sure that the flux is spread to both surfaces if not directly applying to both inside and outside surfaces to be soldered.
Thanks for the comment
I copied method this using compression fittings and it worked, thanks. Important... If you have side-to-side movement (just not up and down) you will only need one slip joint. 1. cut out piece from stationary pipe 2. fix bit of pipe to one side of tee, 3. put slip joint on stationary pipe, slide out of way, 4. move pipe to side and put on tee and fix, 4. Slide slip joint down and fix. I used 2 slip joints, was only after I was thinking about it, that I realized that as I had side-to-side movement I could have just used 1 slip joint. Thought I would share
Thanks for the comment
Never knew about Slip coupler fittings... more education thanks !!!! 😂😂
A multitool with the appropiate blade will make easy work of cutting ... even a pipe in tight to a corner 😎👍
Thanks for the comment
Man! This video saved me a looooooooooot of time and showed me what I needed to buy! Thank you so much for an amazing video and lesson! 🙏
Wow this is not only a great How To but it is a problem solver for exactly the problem I have at this moment !
Thank you !!!!
I'm glad the video helped
Thanks for the comment 👍
Many DIY videos are garbage. There are so many self proclaimed experts who make videos that are just lousy. I happen to be someone who was trained for and worked in 6 different trades, one of which was Plumbing. I watch these videos for entertainment and do compliment the guys who actually make good videos. This was, by far, the best DIY video on this specific topic I have seen. I subscribed.
Thanks for the comment and the Sub ;-)
I'm constantly impressed with your pragmatic approach to what amounts to perfect teaching skills.
Thanks Frank ;-)
Great video as always. Genuinely surprised those slip couplings didn’t fall down due to gravity when you melted the solder. It’s happened to me in the past. I used an old screwdriver to hold it in place whilst soldering.
Nice video. Well explained as usual 👍
Thanks Graham, I did have a couple of spring clips with me just in case the fittings started to move, but luckily they did not move at all once heated.
Thanks for the comment
At 5:08 good idea on how to determine depth of insertion. I am not a plumber and I have two pipes that are going to require slip couplings and I was trying to figure out a way to know when I was halfway into the coupling. Now I know how. Thank you.
You are welcome
Thanks for the comment 👍
This was great. I'm about to install a tee in a rigid pipe and the way I came up with would have been a nightmare. Thank you for saving me a headache
No problem 👍
Thanks for the great video. This has now solved the mystery of why certain piping in the house had 2 joints.
You are welcome
Thanks for the comment
Brilliant! I’d never heard of slip couplings either and this was exactly what I need to know as I’m about to add a new radiator to our CH. Thank you👏🏻👍🏻😊
Glad it helped 👍
Exactly that's the first time I've ever seen one of those two and I've been doing construction all my
It’s a wet and windy day today, so what better than watching a plumbing video ;-)
I hope everyone has a great Sunday
Ultimate Handyman Snow in Wigan ☃
We have just had an hailstone shower, hopefully the snow will miss Darwen ;-)
Snow in Northumberland and I was fitting downpipes on the windward side of the new house - lovely 😁
Doesnt plumbing work have to be done by a licensed person in the UK?
Ultimate Handyman While drinking a hot cup of tea aye !
Excellent. And thank you for NOT having music.
You are welcome
Thanks for the comment 👍
Thank you.
I just bought a Milwaukee Copper pipe cutter. I need to do what you showed.
Glad I could help!
The Milwaukee cutter looks great ;-)
Thanks for the comment 👍
Thank you. I didn't know slip fittings ever existed.
Glad to help
Thanks for the comment 👍
Nice video. Also if your stuck without a slip coupling you can file down the inside of a regular endfeed coupler. You have to be careful though as the wall of the copper is abit thinner in the middle when you do.
Thanks for the comment
Use a proper 15mm reamer.
Thanks ... I thought you were crazy trying to solder with no solder ... never heard of those new fittings. They look very nice and easy to work with.
Solder ring fittings are very common in the UK, they are often called Yorkshire fittings. I'm not sure how long they have been around over here but I remember seeing them when I was about ten years old, so they are tried and tested.
Thanks for the comment
Here in the U.S. they make what's called C-flux. It has the solder in solution with the flux. Very aggressive. I won't use it.
I've never heard of solder ring fittings. Thank you for naming it in the description. I was going crazy trying to figure out if there was a solder and flux combined paste that required no separate solder after you applied the heat.
They are common in the UK, but some countries do not use them (not sure why)
Thanks for the comment 👍
You used one more coupling than needed, join the tee to one end of the cut pipe and then use a coupling on the link piece.
Thanks so much for showing the slip couplings in all the years I've been doing construction I've never seen a slip coupling like that before I always had to use the split coupling boy is I knew they had those it would have made the job a lot less stressful cause when you have a stiff pipe I always had to pull one section of the pipe away from the wall and put the split coupling on it and cut the other side of the pipe a half day-inch shy then we're supposed to be just to get the darn thing on there and the result was I only could put quarter-inch pipe in each side of the coupling and solder it like that which always work but not exactly the way it's supposed to be as the pipe supposed to go all the way to the center of each side of a coupling
I was also like you, it was only when Razor mentioned about slip couplings in the forum, that I knew about them 👍
I didn’t know slip couplings and solved it by putting in 4 elbow joints plus the tee!
👍
Very clever, I didn't know about those fixings, I would probably have put a standard fixing on the lathe and bored it out. Now I know I don't need to. I bet they are are cheaper way to repair pinholes too, probably cheaper and stronger than those ones you showed us recently, assuming you could move the pipe around a bit.
Yes, they are really useful.
Thanks for the comment
Thank you for taking the time to explain this. Saved me a ton of time and frustration.
You are welcome
Thanks for the comment 👍
Great tutorial and I learned plenty to try this myself. Thanks for the show~!!
I’ve done the haksaw way like yourself before then I found me a cheap wire cutter of eBay and just kept it in me plumbing box !
Good video 👍🏼
Thanks for the comment
I've only been in this situation a few times, thankfully.
In a plastered in situation you would need to use 3 pieces but in a clipped in one I would just cut once and unclip one side of pipe and push in the slip fit. But even in plaster I've just cut back the plaster till enough pipe was exposed to bend out.
Good video.
Thanks for the comment
Snowing here in Galway. Handy bit of info in a tight situation.
We have a bit of snow here now as well ;-)
Thanks for the comment
I bought the 15mm nerrad pipe slice and it deburs it for you as you cut the pipe, great piece of kit 👌
I have managed to use a round file to remove the centre stop on end feed couplings before to make a slip coupling. It did the job
Thanks for the comment ;-)
YES! Thank you very much for making this video! You saved me a lot of headaches!
You are welcome
Thanks for the comment 👍
Hacksaw? That's what multitools are for. Yes it really is x4 fast😀
Why 3 fittings? A single T and a single slip coupling will do just as well. Good video for getting the little grey cells working.
If I had used a multi-tool, I would have a hundred comments saying "you could have used an hacksaw"!
The pipe is rigid, that is why 3 fittings were used ;-)
Thanks for the comment 👍
@@ultimatehandyman I bought my multitool to cut a leaking 15mm tee that was 2nd of 4 pipes hard against each other and the underside of the floor above. There was no way to cut it out without taking the house apart around it to get a hacksaw in. I bought a blade that was 16mm wide. The leak was only found when I accidentally left the fill valve on the combi cracked open overnight. I have never been so pleased to be splashing in water in the kitchen in the morning!
@@ultimatehandyman No hes saying you could have just used the one slip coupling on either top or bottom and then use the T connection for your top or bottom piece. Unless you had to be centered in that location hes correct you only needed one slip and 1 tee connection. Regardless it doesn't matter good video. I made the same mistake going into a stack and I used 2 ferncos instead of just one. I'm too use to using ferncos too mate Pvc piping too copper drainage pipe.
Loved it that you added the X4 when sawing the pipe. And here was me thinking the Ultimate meant you could saw at that speed naturally :D
Thanks for the comment
A carbide step drill bit can also splice into copper pipe. Then, you can braze another section of copper pipe into place.
What a really useful vid, didn’t know slip couplings existed. Thanks for sharing
You are welcome
Thanks for the comment
You can't beat a good fluxing, the only thing i would add is poke a good bit of solder in the joint just as she's running, she will remember that for the next 30 years.👍
Thanks for the comment 👍
I love those Yorkshire capillary fittings, we don't use these in the US, but I'd like to get some and experiment.
Yes, they are brilliant- so easy to use!
Thanks for the comment
nice one! good pacing and showing all the steps including how to get into awkward spaces and not cheating! thanks
You are welcome.
Thanks for the comment
I hope father christmas brings him a new pipe slice!
Got one, thanks ;-)
I think it was chrome pipe that blunted that one!
Great video Thanks for sharing this.I did not know they made those couplings that slide all the way threw.
You are welcome
Thanks for the comment
Very clear, very useful knowledge. Top job. Thank you.
Glad it was helpful!
Thanks for the comment 👍
There are very few jobs when the pipe cannot be moved. But V useful when customer has nailed a pipe on a joist.
Brilliant didn't know about the slip fittings
I'm glad the video has helped ;-)
Thanks for the comment
top notch mate, just what I was looking for.... thank you thank you
Thanks for the comment 👍
Another good vid me ol’ mukka. Ta very much
You are welcome
Thanks for the comment 👍
Great 👍,they say you learn something new every day, well I have ,thanks🦖
You are welcome
Thanks for the comment
And in a real desperate emergency you can always file the inside of a standard fitting so it slides up and down the pipe. 👍
Thanks Marc, I was discussing this with a plumber mate of mine a few days back but I was unsure if it would weaken the fitting.
Thanks for the comment
Point taken I wouldn’t be sure. All I know is that it was a last thing on a Friday with water piddling out a fitting and that was all I could think of haha! Shall get some of these fittings though after seeing this! Cheers matey!
I'm sure they would be fine, but best to air on the side of caution.
Thanks for the comments
Easier way above
I have done it many times when i didn't have a slip coupling. Also some of the supply stores sell the slip couplings for 2X or more since the are repair product (excessive imo),
Another excellent job Chez, spot on mate!
Thanks Paul ;-)
Dont forget before soldering to align the T outflow parallel to your wall. If its rotated a bit too much in or out, any long pipe off the T will angle incorrectly.
Thanks for the comment
Very informative, thanks for all your postings.
You are welcome
Thanks for the comment
So my push-fit tee coupling won't help me then! So glad I saw this before I cut the pipe!
No, unless you can move one of the pipes.
Thanks for the comment 👍
Great information! This is exactly my situation. Thanks!
Glad it was helpful 👍
Great video and very useful indeed, many thanks for sharing this top tip with us.
Have a great week,
Joe
You are welcome Joe ;-)
Thanks for the comment
Brilliant videos and very well explained, thank you!
You are welcome
Thanks for the comment
Really useful, thanks, even if I never do that I will know how it should be done.
Glad it was helpful! 👍
Nice video thanks
Thank you too!
Great video, thanks for posting.
Glad you enjoyed it
Thanks for the comment 👍
Thank you
You're welcome
Super video
👍
great advice, thanks Charles of Darwen
You are welcome
Thanks for the comment
1 T and 1 slip. Sawzall with metal blade, jigsaw, etc. 1. Cut out section. 2. Attach the T to removed section. 3. Slide the slip coupling onto the removed section. 4. Cut off the extra length from the removed section that now has attached T and slip waiting to be welded. 5. Connect the T to the pipe. 6. Slide up the slip fitting and weld = done.
Thanks for the comment
Very nice explanation!
Thanks for the comment
Very good
Thanks for the comment ;-)
Another top quality video great work, well done!
Thanks ;-)
Superb, you are always helpful.
Thanks William ;-)
i was scratching my head how I was going to T into a pipe which was otherwise rigidly fixed. Thanks.
I'm glad the video helped
Thanks for the comment 👍
Awesome 👍🏼
Thanks 👍
Simply awesome with the fittings and do you recommend the fittings and are they very reliable. Great job
Yes, solder ring fittings are great, they should last a very long time 👍
Great video.....as a non plumber(but quite handy), I've had that problem a couple of times.....solved it in different ways (not pretty), I wish I'd watched this video first! My latest problem is a shower waste (1.25 ") that is below the 4" main waste. Not
a lot of room below the floor....is there some sort of pump you would recommend ? Keep he videos coming.
Sorry, I know nothing about a pump that would be suitable for that job.
Thanks for the comment
I thought this was a brilliant little vid
Some decent tips
Thanks for the comment
Amazing
personally I would have used a compression 'T' and bored out the web on a pillar drill. You can definitely ease the pipe out of the bracket on one side enough to install the fitting once the pipe has been cut. But if you have to use a solder 'T', then you certainly only need to use a single slip coupling as well to make it work.
Thanks for the comment
excellent video. Thanks !
You are welcome
Thanks for the comment 👍
Another great video.
Thanks for the comment
Thanks for posting very good demo of a tricky sicumstance, I wouldn't have known how to do it. I'm off sick at the moment any chance of a video in the week thanks
Sorry, I'm afraid I don't have any videos ready for upload yet. I'll try and get one filmed one night after work and then edit in time for Sunday.
I hope you get well soon ;-)
found the the video very informative thanks for sharing this inf with us have a good sunday.
You are welcome
Thanks for the comment ;-)
Interesting, explained well. Thanks.
Thanks for the comment
Very well presented video
I’m glad you like it.
Thanks for the comment
I'm not a plumber, just trying to gain some knowledge and i have learned a lot from you so far so thanks. Just wandered why you don't use solder as well as flux like others do. that's got me a bit baffled
Solder ring fittings (Yorkshire fittings) are much easier to use, my videos are aimed at DIY'ers which is why I always use them instead of end feed.
Thanks for the comment
Nice clean work, thanks.
You are welcome
Thanks for the comment
Great video once again learned a lot thanks for the upload
Thanks for the comment
Professional plumbers do use Yorkshire capillary fittings.
Thanks for the comment
@@ultimatehandyman so my mate tells me ed plumbers Yorkshire are better on gas
You can make a slip coupling by putting a steel nipple in the stop coupling and rap on the stop with a ball peen hammer. It flattens the stop.You can clean both ends of short pipe at the same time with a longer piece of sand cloth.
Very helpful! Thanks!
You are welcome
Thanks for the comment 👍
Excellent video, with every step made so easy to follow. I think I've asked if you could explain types and usage of gas blowtorches a few times over the years, sorry to mention it again! 😊 I see you mention them on another comment - your Rothenberger looks really solid and reliable.
I'll try to do a video on Blowtorches when I get chance ;-)
Thanks for the comment
nice one
Thanks 👍
excellent!! Very informative and a new subscriber added
Thanks for the comment and the sub ;-)
Well explained, thanks👍
You are welcome
Thanks for the comment
Thank you for the video.
Thanks for the comment
Cutting that pipe looks like a perfect job for an oscillating multi-tool or small recipro saw.
Yes, that would probably have been quicker.
Thanks for the comment
Would it not have been slightly easier to have cut 90% through that first cut and then done the second, so the pipe is still braced both ends. Then you just have that last little piece left on the first cut to finish off.
Great video.
Thanks David ;-)
Why am I watching this...enjoyed it anyway..
Thanks for the comment ;-)
very smart ideas
Thanks for the comment ;-)
Great job !!!
Thanks for the comment ;-)
Excellent presentation. All it needed was a little "real life" of never ending water gushing out the draining cut ends adding six hours to the job ☺
I've never seen those "self soldering" fittings before. How reliable are they?
I'm curious to know what is and where you got that heat shield cloth you used while using the torch. Looks easier than my method of bent pieces of stainless.
Thanks, have a great week! 🍺
The solder ring fittings, often called Yorkshire fittings are really reliable. I'm amazed that they only seem to be available in the UK as they are so easy to use.
The heat cloth is widely available in the UK and is made from woven glass fibre- fave.co/2BQsuaM
Thanks for the comment ;-)