I didn't solder the solenoids. I cut a thin belt and then superglued it end to end. This belt does not affect the sound. Usually the belt never breaks at the gluing site.
I didn't fancy unsoldering the solenoids to replace the smaller belt you can thread it around the switch contacts using dental hook or similar. It takes a steady hand and lots and lots of patience though.
Спасибо, поменял ремни. Контакт сначала погнул, потом выровнял, не работало. Позвонил контакт под платой, пропаял, заработало. Ещо под прижимнымроликом щёлкнул пластмасса и ролик прижался. Сейчас работает.
Hello Sir. Please let mw know how did you adjust the Level Meter L and R. Just finished to replace the belts and other minor adjustements on mine but did not understood from the Service Manual how to adjust the level meter. Mine its a bit off Thank you
Thank you very much for your help!❤ But can you advice link from eBay or AliExpress where I can order belts? And which mm 3 or 4 my belts? And how much peace’s. Thank you ❤
I was excited at first to replace my belts on my same deck but then the welder .... I think I will try to replace them and if I broke something I will sent it to trash. Which belts must I buy ?
that was a very helpful video, i replaced belts bu unsoliding the circuit too.
I've done a few of these since this video. I'm much faster at it now 😊
Quick reverse is more than Auto Reverse. Quick reverse means, the decks can reverse very quick when blank lead tape is detected
"horrible goopy stuff" wow thats an understatement 😅 that shit is the bane of my existence 😂
I didn't solder the solenoids. I cut a thin belt and then superglued it end to end. This belt does not affect the sound. Usually the belt never breaks at the gluing site.
I didn't fancy unsoldering the solenoids to replace the smaller belt you can thread it around the switch contacts using dental hook or similar. It takes a steady hand and lots and lots of patience though.
I found a really easy way to remove the Rubber "gloop" is to use "Elbow Grease" Degreaser on a cue tip and follow that with alcohol,
Спасибо, поменял ремни. Контакт сначала погнул, потом выровнял, не работало. Позвонил контакт под платой, пропаял, заработало. Ещо под прижимнымроликом щёлкнул пластмасса и ролик прижался. Сейчас работает.
Nice detailed video. Thank you .
afaik the speed adjustment are these 2 potentiometers on the board where all these microswitches are.
thank you very much. Your tips are priceless
Hello Sir. Please let mw know how did you adjust the Level Meter L and R.
Just finished to replace the belts and other minor adjustements on mine but did not understood from the Service Manual how to adjust the level meter. Mine its a bit off
Thank you
Thank you very much for your help!❤ But can you advice link from eBay or AliExpress where I can order belts? And which mm 3 or 4 my belts? And how much peace’s. Thank you ❤
www.ebay.co.uk/itm/326027388831
Thank you very much 😊@@ANTandTEC
Плоский 110 мм, тонкий 65-70 мм.
Where can to buy pinch rollers for AIWA AD-WX929?
I was excited at first to replace my belts on my same deck but then the welder .... I think I will try to replace them and if I broke something I will sent it to trash. Which belts must I buy ?
The solder work is easy if you have an iron, they are large pads.
For the belts just search "AIWA AD-WX929 belts" 😊
Плоский 110 мм, тонкий 65-70 мм.
Дизайн сильный!!!
Adf 1000!