Flexible Hoses SolidWorks 2021 Tutorial! Swept Boss/Base Command step by step!

Hello friends, and welcome back on my channel, in this video I am making another easy part for beginners step by step, I hope I am helping you with this videos to learn SolidWorks faster! If you have any parts like this and you want a tutorial about them, leave a comment, and I will answer you as fast as I can :D
Thank you for watching, and I hope to see you in the next videooo :D see you!
And if you want to support me, you can leave a like/share or subscribe :D
Here is my Facebook page where I am posting some of the drawings that I am using for my videos :) I will try to upload drawings every Sunday for the previous week. #SolidWorks #CAD #HoleWizard
/ alexs-engineering-1146...
Sharing is Caring, any support is welcome www.tipeeestre...
-How to activate "Dynamic mirror entities" see in this Tutorial:
• SolidWorks Double Bear...
-How to limit Movement in Assembly:
• How to LIMIT the MOVEM...
-How to make a MOLD:
• How to make a MOLD in ...
-How to use BELT/CHAIN command:
• How to use BELT/CHAIN ...
-How to make EXPLODE VIEW:
• Explode View!! SolidWo...
-How to use AUTOTARCE :
• How to use AUTOTRACE t...
-How to Engrave a Picture on a Sphere:
• How to ENGRAVE a PICTU...
-Tips & Tricks SolidWorks: • SolidWorks Tips & Tricks

[@subashniraula4443]

Hello, I am using this same way to make piping for hot tub. But my problem is that the pipe is not hollow inside. Is yours hollow? any suggestions? Thanks.

[@AlexsEngineering]

yes it is hollow inside, if you look at minute 2:40 you can see that is hollow inside, just follow the tutorial and your hose will be also hollow

[@irfanyusuf3992]

why i cant make it tangent to the temporary axisZ?

[@joeyqueen9094]

I keep getting an "over defined" message when I try to make the spline tangent. Does the whole assembly need to be locked?

[@AlexsEngineering]

it depends what assembly you have, in my case I have some moving parts which are not locked. So try to delete some constraints from the spline line to make it more flexible

[@Welightonejessica]

Nice job, congrats.

[@AlexsEngineering]

Thank you 🤗

[@qozia1370]

Thanks!

[@AlexsEngineering]

Welcome!

[@ravinderkumar526]

please make a wire braiding video

[@chauhanmanish4381]

Thanks brother

[@AlexsEngineering]

You're welcome

[@bollywoodsongs3490]

Good

[@AlexsEngineering]

Thanks

[@w.binder-freecadchannel]

Vera nice👍😀

[@AlexsEngineering]

Thank you 🤗

[@PedroRodrigues-rj8hu]

great!!

[@AlexsEngineering]

Thank you 🤗

[@cheenu_]

I cant able to select the path

[@alexanderj4545]

Do you know why I can´t get the end of the spline (2:00) to mate with the centerline...

[@AlexsEngineering]

I don't know, have you tried again? try again and follow the steps in the video, it should work

[@sverre1990]

I had the same problem, but found a work around. Do everything up until point (2:00), then make a axis in your new hose part in each of the two locations, and use those axis' to make the spline tangent.
I was not able to use the temporary axis' as Alex did.

[@damgnj]

Go to the System Options - General, then External References, and check boxes of "Automatically genetate names for reference geometry" and "Allow creation references external to the model"