The theater I volunteer with just installed new ADJ lights: Specifically four ADJ PAR Z120 RGBW units. The setup on the board is as follows: - Light 1 -> Assigned to Fixture 1 (channel 8, address 1) -> Faders 1-4 on the operator board are RGBW. - Light 2 -> Assigned to Figure 2 (channel 8, address 17) -> Faders 1-4 on the operator board are RGBW - Light 3 -> Assigned to Figure 3 (channel 8, address 33) -> Faders 1-4 on the operator board are RGBW - Light 4 -> Assigned to Figure 4 (channel 8, address 49) -> Faders 1-4 on the operator board are RGBW You can see the problem with this setup. While I have individual lighting control as individual fixtures, I cannot have Red on light 1/figure 1 and Green on light 2/figure 2 as sliders 1-4 on channel selection A on the DMX operator board have the same assignments. I would like to setup the DMX board to have the following setup: - Light 1 -> Assigned to Fixture 1 (channel 8, address 1) -> Faders 1-4 on the DMX Operator Board (Page Select A) on the operator board are RGBW. - Light 2 -> Assigned to Figure 2 (channel 8, address 17) -> Faders 5-8 on the DMX Operator Board (Page Select A) on the operator board are RGBW - Light 3 -> Assigned to Figure 3 (channel 8, address 33) -> Faders 1-4 on the DMX Operator Board (Page Select B) on the operator board are RGBW - Light 4 -> Assigned to Figure 4 (channel 8, address 49) -> Faders 5-8 on the DMX Operator Board (Page Select B)on the operator board are RGBW This way I can have individual colors on all four lights at different times. I just have 0 understanding of how to program the lights to be assigned to different faders/page selects on the DMX Operator.
The theater I volunteer with just installed new ADJ lights: Specifically four ADJ PAR Z120 RGBW units. The setup on the board is as follows:
- Light 1 -> Assigned to Fixture 1 (channel 8, address 1) -> Faders 1-4 on the operator board are RGBW.
- Light 2 -> Assigned to Figure 2 (channel 8, address 17) -> Faders 1-4 on the operator board are RGBW
- Light 3 -> Assigned to Figure 3 (channel 8, address 33) -> Faders 1-4 on the operator board are RGBW
- Light 4 -> Assigned to Figure 4 (channel 8, address 49) -> Faders 1-4 on the operator board are RGBW
You can see the problem with this setup. While I have individual lighting control as individual fixtures, I cannot have Red on light 1/figure 1 and Green on light 2/figure 2 as sliders 1-4 on channel selection A on the DMX operator board have the same assignments.
I would like to setup the DMX board to have the following setup:
- Light 1 -> Assigned to Fixture 1 (channel 8, address 1) -> Faders 1-4 on the DMX Operator Board (Page Select A) on the operator board are RGBW.
- Light 2 -> Assigned to Figure 2 (channel 8, address 17) -> Faders 5-8 on the DMX Operator Board (Page Select A) on the operator board are RGBW
- Light 3 -> Assigned to Figure 3 (channel 8, address 33) -> Faders 1-4 on the DMX Operator Board (Page Select B) on the operator board are RGBW
- Light 4 -> Assigned to Figure 4 (channel 8, address 49) -> Faders 5-8 on the DMX Operator Board (Page Select B)on the operator board are RGBW
This way I can have individual colors on all four lights at different times.
I just have 0 understanding of how to program the lights to be assigned to different faders/page selects on the DMX Operator.