How to solve : No results found in NX (CC English included)
HTML-код
- Опубликовано: 22 авг 2024
- No results found is a common error message in NX.
Most time it is that constraint(s) are not defined well.
Or that connected or contactes parts are not connected properly.
This method will show the moving part instead of getting
the error.
youre a beast olaf. had to dig around to find the bailout section but it works now!!!
Thank you
Thank you so much!! Your tip helped me a lot!
Best wishes to you from Spain :D
Thank you, that you took time to thank me :)
What if Parameters (PARAM) isn't found in Case Control?
Do you mean in the window at 1:50?
@@OlafvanBuul yes
What version (updates) of NX12 are you working?select File/Help/About NX
@@OlafvanBuul I Have the same problem with PARAM, I´m use NX 10
I don't have NX10 at hand, but it is similar with NX12 , you should select in NX PARAM, BAILOUT,-1
Trying to run modal free analysis, but there are fatal errors showing up. How to fix it?
1] 7340 Computed Eigen exceed storage
2] I/O error opening 2nd sequential file
3] 3034 internal failure in Lanczos procedure contact siemens
4]Gram Schmidt didnt converge
5] Tri diagonal QL didnt converge
6] No Eigen vectors computed mode synthesis.
How much memory pc and disk do you have free. Does a simple part run?
@@OlafvanBuul Yes simple parts run, only the .afm file assembly is not running, 386 GB space is available
@@mysticflickr7348 hier much pc memory and how many free?
@@OlafvanBuul 1.8 tB is the folder space but 386 gb is free in the folder where I have kept my .afm and simulation
@@mysticflickr7348 That is disk memory but how about your PC RAM memory?
Thank you Olaf!! You helped me a lot!
Thank you for taking time to thank me. :)
hello olaf, when i am performing analysis, "error opening nastran .f06 file" is coming and analysis is terminating at the starting itself.
Can you tell what could be possible reason for that error?
One possibility is that a nastran solver is still running and is writing to this fiel. Check you task manager unde NX if there are nastran running en shut these down
Hello Olaf, I have just created an object, and I tried to solve it, however, the .f06 isn’t showing at all, and the icon of “structural” in results is black and white instead of a colorful one. May I ask, what May be the problem in this case?
Best regards
What for license are you using. A normal or a version with a "crack"? Normally the "cracked"version do not support FEM
I was performing Linear Static Analysis on model having large no. of elements. It is showing error ”Iterative solution failed due to insufficient memory”.
Is it problem with the RAM/hard disk space of computer or otherwise how can we allocate memory for the analysis.
Also for error like “insufficient memory allocated for contact/Glue analysis”, what will be solution for that.
I never encounterde those problems. But have a look at C:\Program Files\Siemens\NX xx.0\NXNASTRAN\conf
astxx.rcf file there are some memory settings.
Thanks a lot, man.
It works for me.
Thank you Olaf!!
What does BAILOUT parameter do?
Hello, thanks for viewing my channel, PARAM, BAILOUT,-1 makes the simulation continue even when there are large displacements in the simulation, in my video the large displacement occurs by "rotating" around the fixed edge.
WoW Thanks a lot!
I don't have f06 but I have f56. why??
I don't know are you using SOL101?
@@OlafvanBuul yes. All my SOL are like that
Wat version are you using?
@@cuongvucong7953
@@OlafvanBuul nx1965
why my *.f06 file has full of FATAL
Does the f06 file state something as MECHANISM near the fatal message?
What type of mesh element ate you using?
that was done. i using 2D mesh.now, how to fix this error "THE FOLLOWING DEGREES OF FREEDOM HAVE FACTOR DIAGONAL RATIOS GREATER THAN 1.00000E+07 OR HAVE NEGATIVE TERMS ON THE FACTOR DIAGONAL". this issue can be :some mesh aren't conected together? how to check meshs are or aren't conected together?
@@trangiangnam1719 did you test with a solution 103 real eigenvalue of everything is connected as expected
Ok