Thank you - I had a problem with my mixer shower not getting hot enough, and the most common advice was to replace the mixer cartridge. However, the advice in this video, particularly about checking the temperature of the hot inlet and ignoring the temperature of any taps (due to different flow rates) made me investigate the boiler instead. Sure enough, it was a boiler fault covered by our insurance - shower now lovely and hot and no expense to us. Thank you again.
Thank you - had low pressure from shower mixer tap - your point 4 made me swap an 8mm bore hose for an 11mm bore and problem solved. Didn't know hoses came with different bores!
I'm hoping you might be able help me with some advice please? My Son has an old Grohe 1000 mixer shower, I think it's a 34161? For some reason, the water has completely stopped flowing through the shower, one day flowing normal, the next day, nothing! not even a dribble. The connections to the big Y shaped valve seem fine, and all the other taps work normally. I'm hoping you might have come across this before, and might have an idea on a fix please? Thank you in advance🙂
Hi just watched your video.. my mixer shower is leaking at the bottom of the unit through the temperature control tap would that be a valve too? .. my trouble is I don't know what type of shower it is so don't know where to get a valve 😢 are they one size for most or does it have to be the make? Thank you muchly 😊😊
How can I identify my thermostat cartridge without a manual/receipt, would there be serial numbers on it, as my plumber wants to take the whole unit out of wall with subsequent tile damage as he says impossible to identify.
Great video. Thank you. Need help though.. Water is either very hot or cold, but can't get it warm. When I turn the faucet all the way open to hot it stays hot even if I move handle back to midway. If I turn faucet towards cold and almost close it, it gets cold. Stays cold unless I turn it fully to hot. Can't seem to find warm. I also hear a slight click as I turn to either extreme before the temp changes. Can I fix or should I just replace?
Is it possible for a faulty mixer to allow cool water to flow into the how water lines, thus making the hot water lines all warm instead of hot? If so, how would i find the faulty mixer?
Thanks to this video I was able to replace my cartridge in our shower mixer tap no worries at all but grabbing a generic cartridge from the local hardware store. Had to fix it because tap was off but water would leak out from shower head. Job done, cheers!
And if you have very hard water, you can get a design of shower head that doesn't suffer from buildup at all. I really love my High Sierra shower heads, and this is one of the reasons. I hate those stupid little jets. 😂 I wish it was more obvious to people that occasional maintenance is required on a valve like this. One thing to consider when the hot supply line is plenty hot but the top setting is not hot enough, is that usually the cartridge can be trimmed/calibrated for temperature. It's a simple task with a slotted screwdriver, a thermometer, and a bucket.
After dismantling the dual regulator shower body enough to take off the water on/off ring to try and replace/repair the handle that had been snapped off by previous owner, and then replacing ring and hot/cold tap the shower will no longer turn off. Hot/cold adjustment works fine but the only way to control the flow is via the isolation valves. Could you suggest any causes please.
My shower is a Mira Event xs thermostatic shower and it operates properly. It's approximately 8 years old. Lately, when turned on, it sounds like a jet engine. Is there a solution?
Thank you very much for your generous provision of information - I just thought I'd share some back! (1)We have a low pressure gravity shower which performed miserably until we discovered the Mira Beat handset, just about their cheapest, about £20. This gives a very impressive jet spray at low pressure and (hard water area, about 4' head) is easily cleaned by rubbing the heel of your hand across the wee rubber jets now and again - dislodges the scale easily. (2) Our ancient Mira 88 won't shut properly so I installed a £3 plastic 1/2" ball valve between the handset and the hose, works great and is easy to open and shut without disturbing the settings. (I did fit a replacement cartridge supplied by your good selves but I think it's beyond fixing.)
A very useful and informative video. My shower bar mixer issue matches closely with point 3 i.e. Shower temperature control has become stiff and tight. The temperature control rotates fine when the shower is on just cold water however, it becomes tight & stiff when hot & Cold water is on. Not sure if it will be fixed by greasing or the whole cartridge needs changing. Please suggest
Super video. Love these guys. Its great to encounter such a definitive authority on showers who also provide a wonderful service in identifying shower valves. Thank you Shower Doctor - intend to source valves etc as approriate and especially where advice provided. What use is the wrong valve
Hi there, Ive got a leak in my bathroom. It's only when I use the rain head. There is no leak while using hand held. Mine is thermostatic bar shower valve. Any help would be appreciated. Thanks
To shower doctor, my mixer shower bar is only running hot, no cold, could you PLEASE advise me as i dont really want to replace the whole unit. I think it may be hard water that is the cause ? Rai x
Hello, great video.I have a question. Water comes out of my shower head and tub faucet after I twist the shower valve, what would this issue be called? I would like to fix this but I am not able to find anything online most likely due to the fact that I don't know what my issue would be called. Thank you
Thank you for your very informative video. I have a different sort of problem with our Hansgrohe Croma shower mixer. All flows, temperatures and pressures in the rest of the house are great. However, the shower starts off at the expect flow and temperature, but after about one minute the shower flow drops to almost nothing. Any ideas?
Hi I need help and the manufacturer is of no help. I have an old Hansa shower mixer that I need to replace but the lever can not be removed as there is no grub screw in the under side of the lever. Do you have any advice?
My boiler cuts on and off when shower is on, hot water pipe going hot and cold. just started happening, put a new bar on and its the same...Baxi are saying its not the boiler??? Says my taps need balancing? What does this mean?
tommy hi, i have a power shower and lately sometimes i turn the shower on and nothing comes out, but then if i turn the hot or cold taps on then turn them off the shower starts. any advice greatly appreciated, thanks.
I have a newly installed thermostatic shower fitted which was fine until I recharged the air bubble in my unvented cylinder Since then, the shower did work a few times but since yesterday, there is no hot water at all. Could this be an issue with the valve? All other hot water taps including the bath are working fine.
Any idea why my shower runs 45 seconds warm water and 10 seconds cold, its like clockwork, same pattern constantly at about 34 degrees celcius. Boiler kicks off for the 10 seconds or so of cold water. Is this likely a boiler issue or shower thermostatic valve issue? boiler is Baxi 105 HE
I am having a thermostatic mixer changed - I have a Megaflo high pressure system - and am trying to find one that will last - I am astonished to find that Grohe etc all now use chrome coated plastic or plastic for their valves and cartridges. I am assuming brass or metal is better - am I mistaken ?? Can anyone recommend a thermostatic mixer for its quality of build rather than its appearance - it would be much appreciated :)
If the shower mixer isn't correctly controlling temperature (hard to have balance warm water, to cold ) and the interior of the mixer is new. What could be the issue?
hi, we have cold water to greens mixer (cartridge)direct from pump approx 55 psi .hot water is from low pressure waterheater filled from headertank in ceiling . our problem is to little coldwater coming from shower head.if we remove cartridge and turn cold water on we get plenty cold water coming out, we already replaced cartridge with new one but no difference. help
Hi I have a temperature problem with my Trevi shower. I have changed the cartridge and it still has the problem. There is plenty of water flowing however the on off (left side) when opening keeps going and the knob spins!
Hi, we have a leak in our shower somewhere causing damage to a nearby architrave. I really like your video and I have a question. If I shower in cold water there is no leak. If I use hot only, no leak. Is it possible the mix of the two causes the leak?
Need help. Just replaced a valve on my mixer shower and now the temperature isn't right. The valve I have changed is not the temp valve but the one that allows the flow through to the shower head. This was done to stop the leak we had which is common and became annoying as its in our en-suite. This now has stopped but still having issues with temp. What could be the cause? Everything use to work (except the dripping issue) before I changed the valve. Thanks.
Excellent presentation. As far as tempering valves go, they are a legal requirement in many countries now and are a safety requirement in all new builds, and replacement hot water units.. And the quality of these valves has slipped badly in recent years with many failing just after warranty runs out. Funny that.
Mixer Taps Shower head dripping - Ive watched your video on this and checked mine which is dripping. On changing the O rings on both ends of the shower hose the dripping is still happening - I’m presuming therefore that it will need a replacement hose, though should I be checking some other part before wasting money. Thanks in advance.
Hi it wont be the hose that's leaking it will be the shower valve itself! The hose just Carrie's the water from the valve to the shower head , to rule out it's not the hose, completely remove it from the shower valve & if it drops from the shower valve itself then it is the valve not the hose . If the valve doesnt leak at all then theres a possible leak in the hose itself, cheap fix . What's worth mentioning is , if the shower valve is if an age it might not be worth throwing loads of money at it & putting it towards a new one with a decent warranty. These guys are a great help if you get stuck give them a call & they'll sort you out 👍
Hi I have a mixer shower it was gravaty fed from tanks in loft .......we have had a boiler change and we are now combi so they cut the pipes in the loft ...........all water works fine .....if I use the shower now it works great for 30-40 seconds the it littrally stopped ...*1st time it stopped we blew a pipe......we fixed it .....we re tried the shower water stopped again .......anyone know why ???? Thank you .....again it worked ok when gravaty fed ......
Hi mate, I moved into the new Gleeson home in Knowsley with a thermal shower fitted by them that I paid extra. The thermal shower that started dripping after I moved in for less than two years. They refused to fix it. Do I need to replace the cartridge to stop the dripping? I just used it for less than two years. Do you think the builder used the poor quality of thermal shower so that it started dripping even in just less than two years time? If I need to replace the cartridge, can I get the universal one or I have to get the one from the manufacturer of such particular thermal shower? Thanks for helping!
a lot of these showers are made in China ,some are assembled over here but the component parts are made in China,,may be its time to replace with a quality shower .worth the extra cost Mira or similar IMO..
Hi George, I have a concealed Thermostatic Mixer Shower and it is very hot at the moment. The hot water flow from the tank is fine. When I shut the hot water flow, there is hardly any cold water. I have taken off the decorative cap on the spindle(handle) and tried calibrating, but no luck. Any advice is greatly appreciated. Thanks.
My shower all of a sudden has a long delay from becoming hot or cold when changing from hot to cold vice versa any help would be appreciated it's driving me nuts it'll be too hot then I turn it down and the pressure drops but stays boiling hot then turns freezing cold then I turn it back to hot and gets boiling hot again almost instantly
I have just followed your great instructions to replace a thermal switch and wanted to thank you so much as I completed the job per your instructions thank you
hmm, so in regards to my problem i think nr 3's the problem that im facing (the temperature regulator has deadlocked on me, so i can't regulate the temperature, meaning i get insanely hot showers)
Hello we have a mixer tap for the shower but the lever is stuck & won't shut the water off. We think it has been turned too far is there any way we can fix this? We think it is a bensham exposed shower unit if this helps.
I have bar mixer and shower head is dripping constantly so it means there is fault in cartridge...Can anyone tell what kind of problem is that and how can i fix it ???
Hi there, Thanks for the informative videos. I have an issue with a faulty diverter in an Ideal Standard Bath/Shower mixer unit (Academy) and I wondered how I get the top of the unit off from above (I don't want to remove the bath side panel as it's sealed with ceramic tiles and mastic). Is there a conversion kit available as the best price I can see for a like-for-like replacement (E960190AA) is £142, plus VAT!! Cheers.
My master shower runs out of hot water after 5 minutes. No hot water at all. However, every other faucet and shower does not lose hot water. What could cause this problem?
I need help with the number two problem I looked for a video on line but I can’t find one my temperature of my shower fluctuates from boiling hot to freezing cold I would like a video on how to troubleshoot/fix that problem but I cannot find one maybe you can refer me to a video or create one yourselfIt would be much help and much appreciated thank you
My shower head is dripping and i have changed the shower head but still it's leaking... Could you please share a video link how to fix the mixer bar please.
I get asked to look at thermostatic shower mixers, and a lot of them have no identity, and they have been bought from places like wickes, and when you try a get parts for them, they are obsolete, what a waste of time and money, I try to get the people to use isolators and strainers, soft water to prevent scaling, but they are mainly concerned about looks rather than functionality, a bit short sighted. I use to work full time, in general hospitals for years, where things need to be reliable, used " Walker Crosweller ( Leonard brand ) " Meynell and Horne valves, good quality, but did not have soft water, so they usually scaled up, but you would have a job descaling them, when the bimetal spring was copper plated, so difficult to sort out. I never use the shower hose you exhibited,, I use hansgrohe Isiflex shower hose, or similar. they never seem to get kinked. I like electric thermostatic showers, no long wait for the temperature to be reached, unaffected by other tap users, less water wasted, including the, what was hot water in a dead leg to the shower. plus I have the mains water supply going through a DVA water softener, meaning no lime scale, no soap scum. thanks for your video, always happy to learn, as I will never know every thing.no matter how long I live.
so, we had bad clogged pipes, i put pex in with hammer preventers. all was well for a month. now it slams inside the valve loudly providing only hot and cold, no mixing. i installed a new american standard cartridge but its the same. as a tile guy, im at a loss here :(
After replacing the shower Moen cartridge, we finally have hot water, but now there is a water leak where the knob and the round plate meets. Could it be a defective cartridge?
Hi Cecile, George has answered your question during our live stream yesterday. Here's the link to the recording: ruclips.net/video/hP3yCSpynOc/видео.htmlm4s We hope this helpes.
The mixers seem to clog up with calcium. I fixed mine by dismantling and greasing with silicon a while back, still good. Here’s the fix video ruclips.net/video/k8Aiem2kOgI/видео.html
Biggest problem I’m having wið my shower is when someone is running a tap downstairs it completely loses pressure and can even stop working mid-shower. It’s really annoying
Easy fix Prise if the ceramic centre on the control handle carefully ,in a way you open a tin of paint ! Be mindful to out the plug in in case you drop anything. Once that part is removed there is a nut with a nylon thread tighten that up with a socket set or adjustable spanner dont over tighten it. That should do the trick. If that doesnt do it it might be play in the cartridge itself ! It shouldn't need much tightening to be fair. Once you've done it , re fit the ceramic cover & your good to go 👍
I have a Myra mixer shower and was running hot and cold, I was told by a British gas “ ENGINEER” it was the shower cartridge that needed replacing. Eventually I solved the problem myself , it was my faulty combi boiler needing a simple diaphragm replacing. AVOID BRITISH GAS who simply can’t be bothered.
Why can't you show the shower in place and then show how to dismantle it. The shower bits shown are alien to me, only the shower head is familiar. I wouldn't have a clue how to dismantle the mixer part to get to washers etc.
Thank you - I had a problem with my mixer shower not getting hot enough, and the most common advice was to replace the mixer cartridge. However, the advice in this video, particularly about checking the temperature of the hot inlet and ignoring the temperature of any taps (due to different flow rates) made me investigate the boiler instead. Sure enough, it was a boiler fault covered by our insurance - shower now lovely and hot and no expense to us. Thank you again.
Thank you - had low pressure from shower mixer tap - your point 4 made me swap an 8mm bore hose for an 11mm bore and problem solved. Didn't know hoses came with different bores!
I'm hoping you might be able help me with some advice please?
My Son has an old Grohe 1000 mixer shower, I think it's a 34161?
For some reason, the water has completely stopped flowing through the shower, one day flowing normal, the next day, nothing! not even a dribble. The connections to the big Y shaped valve seem fine, and all the other taps work normally.
I'm hoping you might have come across this before, and might have an idea on a fix please?
Thank you in advance🙂
Thank you. Strange water delivery problem was from the inside hose and I had a spare! Thank you!
Your voice is so mesmerising i can't stop listening
Hi just watched your video.. my mixer shower is leaking at the bottom of the unit through the temperature control tap would that be a valve too? .. my trouble is I don't know what type of shower it is so don't know where to get a valve 😢 are they one size for most or does it have to be the make? Thank you muchly 😊😊
How can I identify my thermostat cartridge without a manual/receipt, would there be serial numbers on it, as my plumber wants to take the whole unit out of wall with subsequent tile damage as he says impossible to identify.
Great video. Thank you. Need help though.. Water is either very hot or cold, but can't get it warm. When I turn the faucet all the way open to hot it stays hot even if I move handle back to midway. If I turn faucet towards cold and almost close it, it gets cold. Stays cold unless I turn it fully to hot. Can't seem to find warm. I also hear a slight click as I turn to either extreme before the temp changes. Can I fix or should I just replace?
Is it possible for a faulty mixer to allow cool water to flow into the how water lines, thus making the hot water lines all warm instead of hot?
If so, how would i find the faulty mixer?
Thanks to this video I was able to replace my cartridge in our shower mixer tap no worries at all but grabbing a generic cartridge from the local hardware store. Had to fix it because tap was off but water would leak out from shower head. Job done, cheers!
And if you have very hard water, you can get a design of shower head that doesn't suffer from buildup at all. I really love my High Sierra shower heads, and this is one of the reasons. I hate those stupid little jets. 😂
I wish it was more obvious to people that occasional maintenance is required on a valve like this.
One thing to consider when the hot supply line is plenty hot but the top setting is not hot enough, is that usually the cartridge can be trimmed/calibrated for temperature. It's a simple task with a slotted screwdriver, a thermometer, and a bucket.
Is it possible to do a video on how to fix # 1 1. Shower head dripping? Thanks!
Hello, my hot and cold pipes are the wrong way around, can that effect my temperature gauges in controlling hot and cold?
After dismantling the dual regulator shower body enough to take off the water on/off ring to try and replace/repair the handle that had been snapped off by previous owner, and then replacing ring and hot/cold tap the shower will no longer turn off. Hot/cold adjustment works fine but the only way to control the flow is via the isolation valves. Could you suggest any causes please.
Thanks for your video, it really helped. My shower just stopped. Watched your video. Checked valve and yes it's open circuit. :)
I have a shower mixer bar, the FLOW knob has a button, don't want to have to push the button to get a full flow can this be disabled hangrowe
My shower is a Mira Event xs thermostatic shower and it operates properly. It's approximately 8 years old. Lately, when turned on, it sounds like a jet engine. Is there a solution?
Thank you very much for your generous provision of information - I just thought I'd share some back!
(1)We have a low pressure gravity shower which performed miserably until we discovered the Mira Beat handset, just about their cheapest, about £20. This gives a very impressive jet spray at low pressure and (hard water area, about 4' head) is easily cleaned by rubbing the heel of your hand across the wee rubber jets now and again - dislodges the scale easily.
(2) Our ancient Mira 88 won't shut properly so I installed a £3 plastic 1/2" ball valve between the handset and the hose, works great and is easy to open and shut without disturbing the settings. (I did fit a replacement cartridge supplied by your good selves but I think it's beyond fixing.)
3:27 😅
A very useful and informative video. My shower bar mixer issue matches closely with point 3 i.e. Shower temperature control has become stiff and tight. The temperature control rotates fine when the shower is on just cold water however, it becomes tight & stiff when hot & Cold water is on. Not sure if it will be fixed by greasing or the whole cartridge needs changing. Please suggest
This is so useful. Thank you
Super video. Love these guys. Its great to encounter such a definitive authority on showers who also provide a wonderful service in identifying shower valves. Thank you Shower Doctor - intend to source valves etc as approriate and especially where advice provided. What use is the wrong valve
Glad to hear it! Thanks, Michael.
Legend. Was a kink in my shower tube restricting flow. A calpol dispenser shoved in and cleared the fault!
Hi can you replace Kohler seals on the valve I have 2 levers on the head
Hi there, Ive got a leak in my bathroom. It's only when I use the rain head. There is no leak while using hand held.
Mine is thermostatic bar shower valve.
Any help would be appreciated. Thanks
To shower doctor, my mixer shower bar is only running hot, no cold, could you PLEASE advise me as i dont really want to replace the whole unit. I think it may be hard water that is the cause ? Rai x
Thanks for posting. Very useful
Hello, great video.I have a question. Water comes out of my shower head and tub faucet after I twist the shower valve, what would this issue be called? I would like to fix this but I am not able to find anything online most likely due to the fact that I don't know what my issue would be called. Thank you
Thank you for your very informative video. I have a different sort of problem with our Hansgrohe Croma shower mixer. All flows, temperatures and pressures in the rest of the house are great. However, the shower starts off at the expect flow and temperature, but after about one minute the shower flow drops to almost nothing. Any ideas?
Hi i have same problem with hansgrohe mixer, did you get the solution for this problem.
Hi I need help and the manufacturer is of no help. I have an old Hansa shower mixer that I need to replace but the lever can not be removed as there is no grub screw in the under side of the lever. Do you have any advice?
My boiler cuts on and off when shower is on, hot water pipe going hot and cold. just started happening, put a new bar on and its the same...Baxi are saying its not the boiler??? Says my taps need balancing? What does this mean?
tommy hi, i have a power shower and lately sometimes i turn the shower on and nothing comes out, but then if i turn the hot or cold taps on then turn them off the shower starts. any advice greatly appreciated, thanks.
I have a newly installed thermostatic shower fitted which was fine until I recharged the air bubble in my unvented cylinder
Since then, the shower did work a few times but since yesterday, there is no hot water at all. Could this be an issue with the valve? All other hot water taps including the bath are working fine.
Any idea why my shower runs 45 seconds warm water and 10 seconds cold, its like clockwork, same pattern constantly at about 34 degrees celcius. Boiler kicks off for the 10 seconds or so of cold water. Is this likely a boiler issue or shower thermostatic valve issue? boiler is Baxi 105 HE
Extremely informative video thank you very much
I am having a thermostatic mixer changed - I have a Megaflo high pressure system - and am trying to find one that will last - I am astonished to find that Grohe etc all now use chrome coated plastic or plastic for their valves and cartridges. I am assuming brass or metal is better - am I mistaken ?? Can anyone recommend a thermostatic mixer for its quality of build rather than its appearance - it would be much appreciated :)
Thanks man, took my show apart, cleaned it, replaced the hose...all good now!
If the shower mixer isn't correctly controlling temperature (hard to have balance warm water, to cold ) and the interior of the mixer is new. What could be the issue?
hi, we have cold water to greens mixer (cartridge)direct from pump approx 55 psi .hot water is from low pressure waterheater filled from headertank in ceiling . our problem is to little coldwater coming from shower head.if we remove cartridge and turn cold water on we get plenty cold water coming out, we already replaced cartridge with new one but no difference. help
Hi I have a temperature problem with my Trevi shower. I have changed the cartridge and it still has the problem. There is plenty of water flowing however the on off (left side) when opening keeps going and the knob spins!
Hi, we have a leak in our shower somewhere causing damage to a nearby architrave. I really like your video and I have a question. If I shower in cold water there is no leak. If I use hot only, no leak. Is it possible the mix of the two causes the leak?
Hi I want to change the thermostat on my aqualisa 609 do I have to turn off the hot and cold , the water it is dripping, I have a new combi boiler
Need help. Just replaced a valve on my mixer shower and now the temperature isn't right. The valve I have changed is not the temp valve but the one that allows the flow through to the shower head. This was done to stop the leak we had which is common and became annoying as its in our en-suite. This now has stopped but still having issues with temp. What could be the cause? Everything use to work (except the dripping issue) before I changed the valve. Thanks.
Excellent presentation. As far as tempering valves go, they are a legal requirement in many countries now and are a safety requirement in all new builds, and replacement hot water units.. And the quality of these valves has slipped badly in recent years with many failing just after warranty runs out. Funny that.
Very good little video. Solved my problem!
Great video. Plese link me to your video on dealing with No. 3 about stiff controls affecting shower water output.
New thermostatic blender with very poor hot water pressure. If I disassemble it, pressure is fine, but then I cannot control temperature.
Mixer Taps Shower head dripping - Ive watched your video on this and checked mine which is dripping. On changing the O rings on both ends of the shower hose the dripping is still happening - I’m presuming therefore that it will need a replacement hose, though should I be checking some other part before wasting money. Thanks in advance.
Hi it wont be the hose that's leaking it will be the shower valve itself! The hose just Carrie's the water from the valve to the shower head , to rule out it's not the hose, completely remove it from the shower valve & if it drops from the shower valve itself then it is the valve not the hose . If the valve doesnt leak at all then theres a possible leak in the hose itself, cheap fix .
What's worth mentioning is , if the shower valve is if an age it might not be worth throwing loads of money at it & putting it towards a new one with a decent warranty. These guys are a great help if you get stuck give them a call & they'll sort you out 👍
Well made, clear and helpful video.
Hi I have a mixer shower it was gravaty fed from tanks in loft .......we have had a boiler change and we are now combi so they cut the pipes in the loft ...........all water works fine .....if I use the shower now it works great for 30-40 seconds the it littrally stopped ...*1st time it stopped we blew a pipe......we fixed it .....we re tried the shower water stopped again .......anyone know why ???? Thank you .....again it worked ok when gravaty fed ......
Hi mate, I moved into the new Gleeson home in Knowsley with a thermal shower fitted by them that I paid extra. The thermal shower that started dripping after I moved in for less than two years. They refused to fix it. Do I need to replace the cartridge to stop the dripping? I just used it for less than two years. Do you think the builder used the poor quality of thermal shower so that it started dripping even in just less than two years time? If I need to replace the cartridge, can I get the universal one or I have to get the one from the manufacturer of such particular thermal shower? Thanks for helping!
a lot of these showers are made in China ,some are assembled over here but the component parts are made in China,,may be its time to replace with a quality shower .worth the extra cost Mira or similar IMO..
Hi George,
I have a concealed Thermostatic Mixer Shower and it is very hot at the moment. The hot water flow from the tank is fine. When I shut the hot water flow, there is hardly any cold water. I have taken off the decorative cap on the spindle(handle) and tried calibrating, but no luck. Any advice is greatly appreciated. Thanks.
My shower all of a sudden has a long delay from becoming hot or cold when changing from hot to cold vice versa any help would be appreciated it's driving me nuts it'll be too hot then I turn it down and the pressure drops but stays boiling hot then turns freezing cold then I turn it back to hot and gets boiling hot again almost instantly
george galloway has calmed down a bit
I'm aware of all Gorgeous George's faults, but he never fails to entertain. I wish all politicians had the gift of comedy.
Very clear explanations. Thanks
I only get 8-9 minutes of hot water, and then it no longer works any longer and i only get cold water. Any idea what the issue is?
Thank you so much for uploading this! Great and very informative video!
I have just followed your great instructions to replace a thermal switch and wanted to thank you so much as I completed the job per your instructions thank you
my mira Advance ATL thermostatic shower turns on then switches off immediately, The water supply and reset lights flash and beeps. Any advice please
hmm, so in regards to my problem i think nr 3's the problem that im facing (the temperature regulator has deadlocked on me, so i can't regulate the temperature, meaning i get insanely hot showers)
Hello we have a mixer tap for the shower but the lever is stuck & won't shut the water off. We think it has been turned too far is there any way we can fix this? We think it is a bensham exposed shower unit if this helps.
I have bar mixer and shower head is dripping constantly so it means there is fault in cartridge...Can anyone tell what kind of problem is that and how can i fix it ???
Hi there,
Thanks for the informative videos.
I have an issue with a faulty diverter in an Ideal Standard Bath/Shower mixer unit (Academy) and I wondered how I get the top of the unit off from above (I don't want to remove the bath side panel as it's sealed with ceramic tiles and mastic).
Is there a conversion kit available as the best price I can see for a like-for-like replacement (E960190AA) is £142, plus VAT!!
Cheers.
thanks i fixed my shower with your advice!
My master shower runs out of hot water after 5 minutes. No hot water at all. However, every other faucet and shower does not lose hot water. What could cause this problem?
Hi, you have some vety useful videos. I have Mira Event XS that runs to hot. Do you know if you can adjust the mix if hot and cold?
Daft question, do I have to turn the water off at the stopcock to replace a cartridge or seal (whichevers causing the stiffness)
i nowadays turn the water of outside at the meter its easier and nothing gets through..
peter abbott i
I took my cartridge out without isolating, just switching it off on the shower bar.
How about high cold water pressure and hot water barley has pressure
I need help with the number two problem I looked for a video on line but I can’t find one my temperature of my shower fluctuates from boiling hot to freezing cold I would like a video on how to troubleshoot/fix that problem but I cannot find one maybe you can refer me to a video or create one yourselfIt would be much help and much appreciated thank you
Love this guy.... Lovely Irish accent.
Sounds Scottish to me
Toby Mcarey it’s a Scottish accent. Nothing like an Irish accent.
DO you have a video on fitting shower reducers? How to fit a shower unit with 1/2 fittings to 3/4 inlet pipes?
Edwin Cheng
Hi Katrina, George has replied to your comment during our live stream last night. Check it out here: bit.ly/2pYl1MU (watch from around 8 min 30 sec).
My shower head is dripping and i have changed the shower head but still it's leaking... Could you please share a video link how to fix the mixer bar please.
.
Thanks alot for the video 👍
my gainsbrough shower is making a squealing noise when I first switch on.would a cartridge replacement cure this?
I get asked to look at thermostatic shower mixers, and a lot of them have no identity, and they have been bought from places like wickes, and when you try a get parts for them, they are obsolete, what a waste of time and money, I try to get the people to use isolators and strainers, soft water to prevent scaling, but they are mainly concerned about looks rather than functionality, a bit short sighted. I use to work full time, in general hospitals for years, where things need to be reliable, used " Walker Crosweller ( Leonard brand ) " Meynell and Horne valves, good quality, but did not have soft water, so they usually scaled up, but you would have a job descaling them, when the bimetal spring was copper plated, so difficult to sort out. I never use the shower hose you exhibited,, I use hansgrohe Isiflex shower hose, or similar. they never seem to get kinked. I like electric thermostatic showers, no long wait for the temperature to be reached, unaffected by other tap users, less water wasted, including the, what was hot water in a dead leg to the shower. plus I have the mains water supply going through a DVA water softener, meaning no lime scale, no soap scum.
thanks for your video, always happy to learn, as I will never know every thing.no matter how long I live.
so, we had bad clogged pipes, i put pex in with hammer preventers. all was well for a month. now it slams inside the valve loudly providing only hot and cold, no mixing. i installed a new american standard cartridge but its the same. as a tile guy, im at a loss here :(
Really useful video, and reading the RUclips attempted subtitles is hilarious 😂
😅
It’s also annoying. Is there a way to turn them off anyone please?
What causes my Triton cold water cartridge to leak....can i repair it instead of replacing it? Only installed 12 months ago.
Great video.
Hi I installed a moen shower mixer and it's not mixing the water properly
After replacing the shower Moen cartridge, we finally have hot water, but now there is a water leak where the knob and the round plate meets. Could it be a defective cartridge?
Hi Cecile, George has answered your question during our live stream yesterday. Here's the link to the recording: ruclips.net/video/hP3yCSpynOc/видео.htmlm4s We hope this helpes.
My shower starts with a little bit cold water and then it goes hot and then boiling hot water, burned my skin several times
The mixers seem to clog up with calcium. I fixed mine by dismantling and greasing with silicon a while back, still good. Here’s the fix video ruclips.net/video/k8Aiem2kOgI/видео.html
What happens if a concealed valve is fitted up side down
Could you please make a video on how to fix a leaking Mira 415, post 1999?
Thanks
my shower was working fine and all of a sudden it's now only running hot even when on cold, any ideas ?
Hi, George has answered your question last night via our live stream: bit.ly/2pYl1MU (watch from around 26 mins in)
I have a similar issue with my shower
Biggest problem I’m having wið my shower is when someone is running a tap downstairs it completely loses pressure and can even stop working mid-shower. It’s really annoying
Hi I have got a ideal blend shower valve with a very loose handle. How do I tighten the handle please.
Easy fix
Prise if the ceramic centre on the control handle carefully ,in a way you open a tin of paint ! Be mindful to out the plug in in case you drop anything.
Once that part is removed there is a nut with a nylon thread tighten that up with a socket set or adjustable spanner dont over tighten it. That should do the trick. If that doesnt do it it might be play in the cartridge itself ! It shouldn't need much tightening to be fair. Once you've done it , re fit the ceramic cover & your good to go 👍
good work. thank you
I have a Myra mixer shower and was running hot and cold, I was told by a British gas “ ENGINEER” it was the shower cartridge that needed replacing. Eventually I solved the problem myself , it was my faulty combi boiler needing a simple diaphragm replacing. AVOID BRITISH GAS who simply can’t be bothered.
What about leaking at main wall connector junction
indigon A call the plumber
Many thanks.
lovely speaking voice
Any suggestions?
If you're heads dripping 😆
Why shower won’t turn off!!!
Our problem is number 2 :/
I grease my valve daily
nice
nice
I knew that would be No.1. No Scotsman could bear watching money go down the drain!
Why can't you show the shower in place and then show how to dismantle it. The shower bits shown are alien to me, only the shower head is familiar. I wouldn't have a clue how to dismantle the mixer part to get to washers etc.
The water coming
I have tub showed and water coming out
he has another video for that ruclips.net/video/iGFsY0i7dKo/видео.html
@@Loftikaz m
No mention of shower body orientation. Install upside down it will not work.