Hey guys! Before hitting it try looking at the fuses on the positive terminal connector. One of mine were blown and it caused the intelligent key light. It costed $25 for a new one at autozone and was easy as hell to fix. Hope this helps someone.
On the cable connecting the cable there will oftentimes be a little box. It's called a fuse but it's a different kind of high amp fuse. It's more of an enlargened kind of fuse @@mrs.madehandsome901
Thank you for the video! My 09 Altima was acting exactly as you show in the video. I removed the panel around the steering column and used a big crescent wrench to bang on the module. Car started up as it always has! I turned it off, got out, locked the doors, then got back in, started it up and drove it around the block. I left the panel loose and have my crescent wrench ready for the next time it happens. Thanks again!
I have just recently run into this problem with my car and it is driving me nuts. I keep getting stranded because my car will not start. So... I started carrying around a similar screwdriver and a hammer and give it a tap when my car misbehaves and will not start. I know it is not a fix but I cannot fix the car like you and I have to wait until payday to take it to get it fixed. Thank you for the video, however. It was very informative and now I can tell if my mechanic is doing right by me by following videos like this. 😉
Call Nissan they might have a recall and you might get it fix for free, if not all you need to do is take the fuse out and since it won’t engage without a fuse you won’t have that problem no more , that’s how I fix mine 09 Nissan Altima
@@BillSW I believe is slot #40 A 10 amp fuse under the engine bay, took the cover under the steering column, Tap the Escl box which is metal box the size of a cards deck until it disengage the lock and allows the car to turn on, once the car is running remove the 10 amp fuse under the hood. Hope this helps. Also call Nissan headquarters. There’s a recall for this.
Ok I finally figured and fixed this problem. Behind the cluster is the BCM. I replaced it along with the fuse block in the engine compartment. wasn't communication between the two. Both from the junkyard $40 reprogrammed the key which were new and was the initial problem. Car started right up.
Nissan Dealer is telling me its the Steering Control Box. With labor is going to cost $1300. How did you eliminate the Steering Control Box as the problem?
On some of the Nissan ,when programming the Key fob, the hazard lights have to be on. Weird thing is theres hardly any info published that tell you this. Nissan is very secretive about a lot of there repair info.
That module was the issue. It got stuck for whatever reason. If you can get the two bolts out, you can push it in and start it. Some people drill a hole through it and stick a screw in it to prevent it from ever locking up.
Same symptoms are in a car I went too check! No communication with the key! No lights on the cluster only the message center with a key message! No communication with the scanner! I have the IM600 profesional lock smith key programming tool doesn’t let you communicate with the module,went home check Mitchell 5 check schematic! Check power distribution and everything check out... not too mention in this Nissan you have to check the positive battery terminal because the have fuse links...then I watched your video and bingo that was the problem! So I recommend too safe time and take it to Nissan because of the issue going on with aftermarket parts and learning key’s... thank you for your video was right in the money!
@@NNKH2 Well you remember I say too take the Nissan Altima to the Dealership but no he buy the Dorman part# 601-037 that’s comes with the programming tool well that doesn’t work and before you start programming they ask you if the key fob key work the lock and unlock and that was working...after a firs try nothing works! Hum Saturday night working with this situation and I send a link of your video! Well I have to pull my IM600 and know I have access but this is the tricky part is like the Mazda the tool pull a 5 digit code then you have to go on the wed and pay for tokens and get the PIN calculation. I use this website and is 24/7 ... weboctopus.nl that’s the best...! An the tokens never expire!!! Cars is running that’s fix...but my friend what a nightmare! I should make a video ...
@@DaelinTV took out the panel on the left and middle (prying it open with a butter knife), then used the bottom of a screwdriver to hit the interlock module a number of times
@@stevet9374 and that held up? I tried smacking it without taking the panel off from the small side facing the brake pedal. Did you hit it from the bottom (the large face)
@@DaelinTV yup hit it from the center bottom…Kept smacking it constantly and then hit the start button, and repeated until everything started. Basically there is tiny motor like part in the interlock that is stuck. Smacking it constantly seemed to loosen it up
@@serenitymareebeauty it's a lock under the steering they stopped using that system so they will replace another box with no lock so u won't have the issue again
Moral of all this. Is this model’s ignition component needs to go. If this many customers ate having issues. They need a better ignition switch. This many customers should not be having an issue with it!
Hey thank you for the video. it’s happened to me too with after I installed dorman interlock system. Please let me know what did you find out with your Vehicle
step son had an issue with the car not wanting to start intermittently. Replaced the battery as it was bad but the car still would not start. Went through all the steps trying to reprogram keys and checking fuses and what not. Finally this morning i got under the dash and used a blunt phillips and a hammer and gave it a couple light taps and it fired right up. Now the question is replacing the unit will probably be a a deal. I am wondering if there is a work around to getting it disengaged and cutting power to it so it doesn't re-lock.
Supposedly if you pull the steering lock fuse while it's running/disengaged, it will no longer be a problem. I have an OE replacement (found one for $305 on eBay) on the way, but I'm going to try hitting it to start and pulling the fuse until then
If you've been working on cars for any amount of time you should know to never use dorman for anything electrical. Dorman can't even get non electrical components right.
@@DaelinTV not really. My wife's car was having a similar issue. Her main key only starts the car if you use the key (fob) to press the start button. Almost if the antenna in the fob isn't working. It has a new battery so that not it. At the moment we're using her other key. It works like normal. Once it gets nicer out since we're in winter I'll figure out later what's wrong with your original key fob .
@@themechanic6117 ahh her car has a traditional turn key ignition? Mine is only push to start. I wish I could say the same thing and put it off but i can't get it started at all! 😅
@@DaelinTV no her car is only push to start. With one of the key fobs the car only starts if you use the key fob to press the button. Her spare key fob works like normal. As long as it's in the car it will start.
Ok so my 2011 had no problem starting, but recently when at a stop would turn off and shut down my car for 30 seconds then after a minute would say push to start n everything come back on , this is well driving lol any ideas
I'm having this same issue - I have both a red car outline with key in middle and a yellow key light ON. Went in the store came out and would not start. I have two sets of keys (fobs) and tried both so it's not a battery in the fob issue. The tow truck driver checked my car battery and it was 11. (something, a little low but all lights, locks, horn, trunk work with my fob. The car will not move out of park, brake pedal is stiff ... nothing is moving. I have tried the key fob up to the push button, and inserted in the place on the left as you show in your video and nothing. I also listened to your other suggestions but I'm a woman who lives alone and I can't afford to be getting stranded - so I don't want to have to be hitting that box every time to get it started :) So bottom line, should I take it to a reputable auto mechanic shop OR is this something THEY will refer me to the Nissan dealer after they charge me for all the diagnostics? I don't want to pay for double diagnostics and labor ...for sure! Thanks so much for you video!!
the 2009 and 2010 has a recall for the steering interlock. Dealer will replace it for free. They did not notify the public about this because they say it's not a "safety" issue. I beg to differ, if this leaves you stranded in a sketchy area after dark, I would say it IS a safety issue! Just call the dealer and ask about the recall. They will ask for the VIN (vehicle identification number) and verify your vehicle is "covered". Took them 45 minutes for a permanent repair.
It’s a proprietary manufacturer part, I’ve had to deal with it twice and now a possible 3rd time and it’s just barely outside of warranty so I’m fiddling with it at the moment fun times
Having this same problem I was going to bypass the system and remove the fuse. come to find out fuse was missing so when i did some further looking I found that the interlock module was not even there. So i am totally confused my daughter had been driving the car until she got this communication problem with the key and no start. Tried replacing brake switch didn't work. Does any body have any suggestions?
That's exactly what I found on my sons 2010 Maxima. No steering lock sensor module and no fuse. Every other day I have to unlock the doors a few times, put the car in and out of gear and push the start button numerous times. A real pain.
@@kingjova4662 I figured out my problem. It was just a fuse in the fuse box underthe hood. I don't remember the exact one, but I believe the number on it was 15. Hope this helps.
My car will start my fob has to be right on top of my push start. I just replaced my car battery. My fob will not in lock or lock my doors... Any idea what the issue is???
Can anti theft system can be triggered by trying to remove radio without tools, now my car wont keep running for more than half second. How do i fix that?
My 2012 Nissan Altima is having this problem, key light is on and won’t start. It doesn’t have a steering lock module. Any idea what else it could be? Have tried changing battery and key fob battery...
Without looking at it it's hard to take guesses. My best tips would be pretty much the stuff I mentioned in this video. Sorry I couldn't be of more help
@@NNKH2 Thanks, I’ve got it to start now. I followed advice from a forum to shift the gear all the way forward, then all the way back and then return to park. This worked. Hope it helps someone.
same thing for me. smacked it a few times, nothing. almost gave up, then just quick steady taps and she started up after about 15 seconds. if the first steps dont work, keep tapping. would love to know how to properly replace the part though. last thing i need is the dorman curse!
Can you plz help me my car won’t start and my greatest fear is having to take it to Nissan they try to rip me off so badly every time I cannot afford it. It’s saying my key is not detected and idk why. It’s a 2019 Nissan Altima. I changed the key fob battery and yesterday it started after a charge but today saying key not detected again.
That problem is the steering lock mechanism which nissan will replace for free under a recall and the updated part they removed the lock don't waste your money on aftermarket
Just so u know this car is a maxima not an altima also that mechanism is covered under a recall from Nissan in 2009 they have a replacement that does not have that lock anymore and u need the updated part u don't go on amazon or ebay for this cause u will have the issue again I now own a 2012 and they no longer use that box
Hi I have a question about my 2012 Nissan Altima... what can I do i have to fix if every time I get in the car I need to insert the key fob in the little port?
This video just saved me. I was stuck in a parking lot out of town with the same problem. The hammer worked! Thank you so much.
Hey guys! Before hitting it try looking at the fuses on the positive terminal connector. One of mine were blown and it caused the intelligent key light. It costed $25 for a new one at autozone and was easy as hell to fix. Hope this helps someone.
What’s the name of the part I ask for?
Fuses on a battery? What?
On the cable connecting the cable there will oftentimes be a little box. It's called a fuse but it's a different kind of high amp fuse. It's more of an enlargened kind of fuse @@mrs.madehandsome901
Thank you
Thank you y'all have a great day
Thank you for the video! My 09 Altima was acting exactly as you show in the video. I removed the panel around the steering column and used a big crescent wrench to bang on the module. Car started up as it always has!
I turned it off, got out, locked the doors, then got back in, started it up and drove it around the block. I left the panel loose and have my crescent wrench ready for the next time it happens.
Thanks again!
Rr
Cc cc or
0e
P4
Ok make
R
Does that really work? I am having exactly same issue.
@@4DMavrick yes, I've done banged on the gray module under the steering wheel and it has worked everytime
@@diaz93tx it’s worked for me the last 2-3 times but now stopped working. Did it stop working for you?
the fact that a car won’t start because they chose a key fob over a standard key is bonkers
I have just recently run into this problem with my car and it is driving me nuts. I keep getting stranded because my car will not start. So... I started carrying around a similar screwdriver and a hammer and give it a tap when my car misbehaves and will not start. I know it is not a fix but I cannot fix the car like you and I have to wait until payday to take it to get it fixed. Thank you for the video, however. It was very informative and now I can tell if my mechanic is doing right by me by following videos like this. 😉
Call Nissan they might have a recall and you might get it fix for free, if not all you need to do is take the fuse out and since it won’t engage without a fuse you won’t have that problem no more , that’s how I fix mine 09 Nissan Altima
@@tonytijuana4132 which fuse did u take out?
I’ll let you know this afternoon, I’m off too work now. But whatever you do , only pull the fuse when the car is running.
@@BillSW I believe is slot #40 A 10 amp fuse under the engine bay, took the cover under the steering column, Tap the Escl box which is metal box the size of a cards deck until it disengage the lock and allows the car to turn on, once the car is running remove the 10 amp fuse under the hood. Hope this helps. Also call Nissan headquarters. There’s a recall for this.
@@tonytijuana4132 Thx for the info!
Thanks for your help. Hitting the box lightly with my foot did the trick.
Excellent!
Same thing happened to me in a 2008 Altima exactly the same, I hit it a few times and nothing, until finally it did start, so thank you!
Ok I finally figured and fixed this problem. Behind the cluster is the BCM. I replaced it along with the fuse block in the engine compartment. wasn't communication between the two. Both from the junkyard $40 reprogrammed the key which were new and was the initial problem. Car started right up.
Nissan Dealer is telling me its the Steering Control Box. With labor is going to cost $1300. How did you eliminate the Steering Control Box as the problem?
@@jacquelinespaulding2200 p
Pl
This BCM and fuse box doesnt fix the problem. No power to the ECM. Key with yellow box is still showing
@Dammie2great behind the cluster is another module grab one the yard as well
@@Dammie2great did you reprogram the key yet
On some of the Nissan ,when programming the Key fob, the hazard lights have to be on. Weird thing is theres hardly any info published that tell you this. Nissan is very secretive about a lot of there repair info.
Its in the repair manual for the car, it is only to keep the BCM from going to sleep, since the programming takes at least 1/2 hour.
That module was the issue. It got stuck for whatever reason. If you can get the two bolts out, you can push it in and start it. Some people drill a hole through it and stick a screw in it to prevent it from ever locking up.
gave the box a few heavy smacks, it started right away. THANK YOU
Just tried the hammer and it works 💪🏾thanks my guy.
@@kingceez5982 did the problem return?
Same symptoms are in a car I went too check! No communication with the key! No lights on the cluster only the message center with a key message! No communication with the scanner! I have the IM600 profesional lock smith key programming tool doesn’t let you communicate with the module,went home check Mitchell 5 check schematic! Check power distribution and everything check out... not too mention in this Nissan you have to check the positive battery terminal because the have fuse links...then I watched your video and bingo that was the problem! So I recommend too safe time and take it to Nissan because of the issue going on with aftermarket parts and learning key’s... thank you for your video was right in the money!
Thanks so much for sharing your experience with this particular problem. Glad the video was helpful and I really appreciate the feedback. Thanks!
@@NNKH2 Well you remember I say too take the Nissan Altima to the Dealership but no he buy the Dorman part# 601-037 that’s comes with the programming tool well that doesn’t work and before you start programming they ask you if the key fob key work the lock and unlock and that was working...after a firs try nothing works! Hum Saturday night working with this situation and I send a link of your video! Well I have to pull my IM600 and know I have access but this is the tricky part is like the Mazda the tool pull a 5 digit code then you have to go on the wed and pay for tokens and get the PIN calculation. I use this website and is 24/7 ... weboctopus.nl that’s the best...! An the tokens never expire!!! Cars is running that’s fix...but my friend what a nightmare! I should make a video ...
@@PeteSambolin There are free programs to get pin code, you don't need tokens.
@@tedmoss you need to pay for tokens is not free!
so did you fix the altima problem?@@PeteSambolin
Man thank you my girls just did this and I could not figure it out for nothing.
Had a similar problem today. 2009 altima. Hit the interlock module a few times and kept hitting the start button. Finally worked.
Where did you hit it exactly, did you take your panel off for better access? I guess that will tell me where you hit it.
@@DaelinTV took out the panel on the left and middle (prying it open with a butter knife), then used the bottom of a screwdriver to hit the interlock module a number of times
@@stevet9374 and that held up? I tried smacking it without taking the panel off from the small side facing the brake pedal. Did you hit it from the bottom (the large face)
@@DaelinTV yup hit it from the center bottom…Kept smacking it constantly and then hit the start button, and repeated until everything started. Basically there is tiny motor like part in the interlock that is stuck. Smacking it constantly seemed to loosen it up
Its covered under a recall go get it replaced at no cost the updated part no longer has this issue
You saved my life mate. Thank you
Step 2 (insert the fob) worked for me. THANK YOU!
What was the problem u had before would help?
The knock did the job. Thank you very much!
I’m having the same issue can’t wait to go back to my car and try it 👍 THANKS FOR THE VIDEO
go to nissan its covered under a recall warranty still and they no longer use that lock
@@fortnite360HZ Whats all requirements?
@@fortnite360HZ I thought the warranty for the steer lock recall expired years ago.
@@cactusjackNV in Canada they honored it at Nissan cause it's a known issue
@@fortnite360HZ That's good to hear.
So what I took away from this video was “If all else fails use a hammer.”
Lol yup!
@@NNKH2 so what was the outcome?
😄 I am using a hammer right now until payday when I can take my car to my mechanic. Yes, if all else fails, use a hammer.
Thanks for a real life video. I have the same problem.
thank you so much!! I just tried this & it worked for me!! I have a 2009 Nissan Altima !! Thank youuuuu!!
Hey bro your key was in that slot backwards but your method definitely worked
tried it, starting fine now Thanks
Thank you. I just earned $150.00 in 10 minutes. It really did work!
A quick couple of knocks and it worked lol thank you
Put car in neutral guys that’s what worked for me
You know what Eric O would say about Dorman? Just because it's new doesn't mean it's good. But yeah yikes that it bricked the bcm
That worked, tapped it a few time with my hammer and car started,. Thanks!
Sweet!
go to nissan and get it replaced for free its covered its a recall and the new updated steering lock mechanism no longer has the lock so go to nissan
@@fortnite360HZwhat is the recall under
@@serenitymareebeauty Steering lock mechanism
@@serenitymareebeauty it's a lock under the steering they stopped using that system so they will replace another box with no lock so u won't have the issue again
Bro!!!! 👏 Thank u for the vid!
This is the answer - all the others with touch fob to start button 👎
Thank you so much for the video, the key in the slot helped me out with my skyline thank goodness ☺️
Moral of all this. Is this model’s ignition component needs to go. If this many customers ate having issues. They need a better ignition switch. This many customers should not be having an issue with it!
Hey thank you for the video.
it’s happened to me too with after I installed dorman interlock system.
Please let me know what did you find out with your Vehicle
step son had an issue with the car not wanting to start intermittently. Replaced the battery as it was bad but the car still would not start. Went through all the steps trying to reprogram keys and checking fuses and what not. Finally this morning i got under the dash and used a blunt phillips and a hammer and gave it a couple light taps and it fired right up. Now the question is replacing the unit will probably be a a deal. I am wondering if there is a work around to getting it disengaged and cutting power to it so it doesn't re-lock.
Supposedly if you pull the steering lock fuse while it's running/disengaged, it will no longer be a problem. I have an OE replacement (found one for $305 on eBay) on the way, but I'm going to try hitting it to start and pulling the fuse until then
Brother you saved my life also. Thanks ✊🏼
If you've been working on cars for any amount of time you should know to never use dorman for anything electrical. Dorman can't even get non electrical components right.
Well since you're here and you're the most recent comment, i assume you're working on a car with this issue? Any luck?
@@DaelinTV not really. My wife's car was having a similar issue. Her main key only starts the car if you use the key (fob) to press the start button. Almost if the antenna in the fob isn't working. It has a new battery so that not it. At the moment we're using her other key. It works like normal. Once it gets nicer out since we're in winter I'll figure out later what's wrong with your original key fob .
@@themechanic6117 ahh her car has a traditional turn key ignition? Mine is only push to start. I wish I could say the same thing and put it off but i can't get it started at all! 😅
@@DaelinTV no her car is only push to start. With one of the key fobs the car only starts if you use the key fob to press the button. Her spare key fob works like normal. As long as it's in the car it will start.
TRUTH!
Ok so my 2011 had no problem starting, but recently when at a stop would turn off and shut down my car for 30 seconds then after a minute would say push to start n everything come back on , this is well driving lol any ideas
Thanks for the honesty
I'm having this same issue - I have both a red car outline with key in middle and a yellow key light ON. Went in the store came out and would not start. I have two sets of keys (fobs) and tried both so it's not a battery in the fob issue. The tow truck driver checked my car battery and it was 11. (something, a little low but all lights, locks, horn, trunk work with my fob. The car will not move out of park, brake pedal is stiff ... nothing is moving. I have tried the key fob up to the push button, and inserted in the place on the left as you show in your video and nothing. I also listened to your other suggestions but I'm a woman who lives alone and I can't afford to be getting stranded - so I don't want to have to be hitting that box every time to get it started :) So bottom line, should I take it to a reputable auto mechanic shop OR is this something THEY will refer me to the Nissan dealer after they charge me for all the diagnostics? I don't want to pay for double diagnostics and labor ...for sure! Thanks so much for you video!!
if u have a 2009 its covered under a recall go to nissan the new part no longer has this issue
the 2009 and 2010 has a recall for the steering interlock. Dealer will replace it for free. They did not notify the public about this because they say it's not a "safety" issue. I beg to differ, if this leaves you stranded in a sketchy area after dark, I would say it IS a safety issue! Just call the dealer and ask about the recall. They will ask for the VIN (vehicle identification number) and verify your vehicle is "covered". Took them 45 minutes for a permanent repair.
Didn't that recall end in 2020?
Nissan Tiana the key sign is indicated too it won't start can I apply what you did in this video
Both of my keyfobs stopped working at the same time. Unhooking the car battery for a few minutes fixed the issue.
So what happened even if you put everything back to OEM it wouldn’t still start back up ? Was it from the upgrade?
It’s a proprietary manufacturer part, I’ve had to deal with it twice and now a possible 3rd time and it’s just barely outside of warranty so I’m fiddling with it at the moment fun times
Thank youuuuuuu!!!! Never knew the key fob was meant to go there
Having this same problem I was going to bypass the system and remove the fuse. come to find out fuse was missing so when i did some further looking I found that the interlock module was not even there. So i am totally confused my daughter had been driving the car until she got this communication problem with the key and no start. Tried replacing brake switch didn't work. Does any body have any suggestions?
That's exactly what I found on my sons 2010 Maxima. No steering lock sensor module and no fuse. Every other day I have to unlock the doors a few times, put the car in and out of gear and push the start button numerous times. A real pain.
I have the same problem. What did you end up doing?
@@robdudzinski3177 I have the same problem. What did you end up doing?
On my 2009 nissan altima, everything turns on like the lights, ac, and even the motor fan, but the engine itself doesn't turn over. Please help!
Having the same exact problem , everything turns on except the engine
@@kingjova4662 I figured out my problem. It was just a fuse in the fuse box underthe hood. I don't remember the exact one, but I believe the number on it was 15. Hope this helps.
@@1kefims did you have to push something back in??? I’m checking right now for all number 15s but everything looks fine
Oh fuckkkkk yeah you’re the best
I unplugged and plugged back in every single 15 and it workedddddddd THANKKKK YOUUUUUUUUUUU!!!!!!
What if thats not there i removed the panel and its not there but the clip for it is would it be somewhere else 2010 Nissan Altima coupe 2.5s
My car will start my fob has to be right on top of my push start. I just replaced my car battery. My fob will not in lock or lock my doors... Any idea what the issue is???
And how much did it cost
Just had a car key guy look at this and the dude tore the actuator apart and fixed it
Thank you Soo much, it really works 👍👍👍
Greetings: If U have 2 hit it more than once, get a larger adjusting device.
Can anti theft system can be triggered by trying to remove radio without tools, now my car wont keep running for more than half second. How do i fix that?
My 2012 Nissan Altima is having this problem, key light is on and won’t start. It doesn’t have a steering lock module. Any idea what else it could be? Have tried changing battery and key fob battery...
Without looking at it it's hard to take guesses. My best tips would be pretty much the stuff I mentioned in this video. Sorry I couldn't be of more help
@@NNKH2 Thanks, I’ve got it to start now. I followed advice from a forum to shift the gear all the way forward, then all the way back and then return to park. This worked. Hope it helps someone.
How did u switch gears if the car won’t start?
brake pedal switch can cause a no start under the brake pedal that switch may need replacing
What did the dealer say?
same thing for me. smacked it a few times, nothing. almost gave up, then just quick steady taps and she started up after about 15 seconds. if the first steps dont work, keep tapping. would love to know how to properly replace the part though. last thing i need is the dorman curse!
go to nissan its free covered under a recall and the new updated part does not have this issue
What needed up happening with the car?
You hit the column or the actual box?
The box
What happened with the maxima . Did the keys have to be reprogrammed?
SO what ever happen to the car After dealer
Nissan wanted to charge my shop $1267 for a 40 min fix.
😟 NO way!! That is awful! I hope they do not charge me that much! 😢
it's under a recall its free from nissan
Can you plz help me my car won’t start and my greatest fear is having to take it to Nissan they try to rip me off so badly every time I cannot afford it. It’s saying my key is not detected and idk why. It’s a 2019 Nissan Altima. I changed the key fob battery and yesterday it started after a charge but today saying key not detected again.
did the car ever start again?? got the exact same prob but hitting the steering interlock did not work
The brake switch is common failure too. Not the problem on the one I'm working on now tho.
You have to change the fob battery once in awhile. I've changed mine twice it's easy.
That problem is the steering lock mechanism which nissan will replace for free under a recall and the updated part they removed the lock don't waste your money on aftermarket
Just so u know this car is a maxima not an altima also that mechanism is covered under a recall from Nissan in 2009 they have a replacement that does not have that lock anymore and u need the updated part u don't go on amazon or ebay for this cause u will have the issue again I now own a 2012 and they no longer use that box
What do we do when banging on that part stops working? Stranded right now
Bang harder?
this is a recall go to nissan and get it fixed with the updated part which no longer has this issue
my key doesn't work and does not open the car what is the problem please help
Didnt need to remove anything. Crawled up under there, pulled on panel and banged away. After 5 blows i could her the power turn on.
Wow. Good job either way
Call Eric o from south main auto
How did you fix by the way?
Just stick the key fob in the compartment push the break and then the start button without removing the keyfob and done
Change the break lock on top of the breaks theres a box on top of the breaks
What the end result at the dealer. I see people asked you but you never replied back.... and happy Father’s Day
Sorry I don't always check the comments on this channel. It went to the dealer. That's all I know. Happy Father's Day back at you
@@NNKH2 thank you
This IA the exact same thing that happened to me right now
My 2012 Nissan is doing that right now I was paranoid sitting in my car at night his I see why it locked in me but sheesh it’s annoying !
Me salvaste , gracias
Thank you so much !
I just change the battery
It works for me
what did? The hammer?
Thank you worked
Dont work for me
Hi I have a question about my 2012 Nissan Altima... what can I do i have to fix if every time I get in the car I need to insert the key fob in the little port?
I think that means the fob battery is dead so the car can only start if it’s in there
That was the start to the problem
Good video …
Doorman is junk. If thats your only option for any aftermarket part, save yourself the headache and go with oem.
its free its a recall go to nissan and change it
SO WHAT WRONG WITH THE CAR
Mane wtf is this shii
I’m having this problem and I hit it I think and nothing still didn’t work
Should've replaced the ignition switch
excelente video muy agradecido
Always use OEM
Set up similar to the 2009 murano
Thank made it simple 😂
Thanks!
it’s a maxima not alrima
Okay. It's spelled Altima btw
Is this supposed to be a joke???
Why
No it worked for my car Im so happy I save so much money today thanks for the video it was a miracle
So complicated why couldn't they just have a key Ignition
It's the steering lock mechanism go to nissan it should still cover under the recall warranty u wasted your money
the recall has expired
@@ashley-rh9wj It shouldn't expire it's not warranty
@@fortnite360HZ it does because nissan sucks. they are charging me 1100$ for the part
It's 500 dollars because they know it's shit
Is anyone else's plastic