Solution: Hiboy scooter Error 7 means the Hall Sensor problem. Usually we have 3 (or 4) Hall sensors in the electric wheel, and 1 in the Speed Accelerator button and 1 in the Stop button on the steering wheel. The problem can be related to the Hall sensor or the wires to the Hall sensor (more often). In my case my wires from the Speed accelerator button were damadged and I had the Error 7. Usualy you can easely check the Hall sensor with minimum efforts. You can try to find video on the youtube. And initialy check the speed and stop buttons wires visualy ;). I hope it can help.
thank you kindly for your timely video. I have the same tester and will now go and put it to use. my project involves 4x 350w bldcm hubb motors. am I able to communicate with you as I go along please?
Thank you. I am currently stranded out 6 miles from home. And I ran into this error. I had some issues with my intertube. I replaced the tire and intertube, but it's so hard to get the tire back on the rim that I ended up putting a hole in the new tube. And I did the same thing again. Then .... I was running into the store to grab a 12" bicycle tube. I came back out to find this error e-007. Then it went back to normal as no error while I was fixing it. Then when I had everything back together, it went randomly error 7 and normal and error 7 then finally got stuck on the error.
This might be the problem I have for my Gyrocopters plaid because every thing works normally when I turn on zero start and push the throttle the motor goes for a sec then e16 pops up on the screen and motor hall anomaly keeps popping up on the app but I don’t have the right tools to open up the motor to check
Hi, question: for my scooter, the motor won't turn smoothly, it is as if something is restricing it. I opened the same way as yours but there is no burning smell or parts fallen appart. The scooter was working fine until I rode it a few minutes on rubble (it was a rough surface) it then just lost power. It's turning on and off, battery indicator is working and when I press the electric brake it restricts the back wheel even more. It's just the acceleration is not working. Please advice:(
I have the same problem my motor wont turn smooth . it is just like something block it . I also open it but nothing to see . I already order 2 motors from zero 10x becouse the original models are shit . upgraded motor type 3 is much better . now I only hope that my controller is not damage becouse off the stuck weel .....
Hi! I just realised your middle sensor in red, the 2 others in blue, so the middle one may not be the same... I replaced it, and still have Error E07... Could you give me all three sensors Part Number please...?
The rear cable also becomes very hot and wheel jams... Some hub motor have a different hall sensor in the middle than the 1st and 3rd.. I think it's the case for the Zero 10X 48V 1000W hub motor, and I must have installed the wrong one..
Cordial friend greetings, can you help me with my ZERO 1OX I have a problem at times when actuating the accelerator does not work and on one occasion going up a hill I braked and at the moment of releasing the brake the scooter was pushed and when actuating the accelerator again did not respond The LCD screen did not show me any error and then while I was at home when trying to enter the menu, the code 7 appeared, which is a fault in the engine, immediately turn off and turn on again, this time it did not appear again, I went out to drive it for a while using the dual motor And in turbo and has not reappeared. I appreciate your help informing me why this is due
I've had the same problem for over a year on the same scooter, attempted to find the problem once before and took the scooter apart, but didn't have the melted solder issue like these guys, don't know what it is, might try looking again and getting a multimeter to test each hall sensor as maybe one needs replacing in comparison to resoldering
Hi I recently had my charger port blown out(fire) im wondering if I replace the port myself will it sort out the issue or nah? because since it burnt out the scooter does not turn on anymore.. So is that an issue with the port or do I need to send it off for repair/replacement?
Well in my example I was a moron and i touched the charging port with metal pliers and it shorted out my zero 9 but when you unplug and plug back in the wires where the battery is located it should turn on fine... I also replaced the charging port cause it was useless after that.
I have a evercross ev08 it's my daughters I'm going through chemotherapy I really need to fix it for her I've repaired all broke wires I just have this white one and there is no place I can see where it came from
I have a LH-100 display with a 1000 watt 48 volt motor. But it gives me error 7 with and without hall sensor connected. I checked from loose wires but couldn't find one. It runs very bad til im at 20 km/h than i can go full throttle without problems to max speed. If i do to much throttle before i reach 20 km/h it goes crazy and stops (breaks with shocks) and i can re-throttle and it'll work. But if i give to much gass it will kick out again. This is only before i reach 20km/h Anyone knows a solution? Please help.....
I just spent $1429 to repair my Wolf warrior x and when They shipped it back to me the display has read error 07 ever since I turned it on after receiving... Seems like after spending $1429 to have it repaired I shouldn't have to deal with this problem !!! Wtf?
My kugoo s1 pro has a m error light on ( I assume it stands for motor) it works then randomly stops accelerating to continue accelerating you have to let go of the throttle and press again for it to accelerate could u help me resolve this issue
The controllers may have to be replaced. Happened to my wolf king yesterday. The scooter is so powerful so the issue of it moving on its own full blast when it’s on is so dangerous.
Why you need to cut open all wires).Just open motor and fix the problem even all cables are connected to controller..is that possible?iv got error 7,but when I restart the scooter it disappeared and working properly...One's i get completely black out,no power suddenly. He doesn't even charge. But after 10 minutes, he just run again, without problems. Do you know what's happening????
He must have shorted it by accident. It’s not a big problem. You just need to open up the deck and unplug and plug in the yellow battery connector. It should work again. But the charging port may be burnt and you may need to change the charging port
Zero 9 with remote immobilizer activated. Everything was working fine for several months but now at 4:30am i was awaken with beeping + locked sounds , throttle shows E 06. Whats this please help? I need to go to work in 30 mins :(
@@FalconpevSg🗣️I WATCHED THIS VIDEO . Y👤U SH🟢ULD SHOW THE RESOLDING PROCESS . ACTUALLY , SHOW Y👤U RESOLDING . I AM DEALING WITH THE SAME E 7 ERROR .>🎤🛴
![YoungBoy Never Broke Again - Missing Everything [Official Video]](http://i.ytimg.com/vi/dTYeMZGzOzw/mqdefault.jpg)
Excellent video gentlemen, much appreciated, thank you deeply 🖤🖤🍻🍻
Thank you very much! I just now know how to get into bearings! You do very good job.
I have a Sunra Miku Max with Bosch engine and the wheel with the engine got very hard to turn. Do you know such issue and potential solution for it?
@@Taylan13 the gears are damaged
Solution: Hiboy scooter Error 7 means the Hall Sensor problem. Usually we have 3 (or 4) Hall sensors in the electric wheel, and 1 in the Speed Accelerator button and 1 in the Stop button on the steering wheel.
The problem can be related to the Hall sensor or the wires to the Hall sensor (more often).
In my case my wires from the Speed accelerator button were damadged and I had the Error 7.
Usualy you can easely check the Hall sensor with minimum efforts. You can try to find video on the youtube.
And initialy check the speed and stop buttons wires visualy ;). I hope it can help.
Thank you for sharing!
Y si no tengo sensor Hall en mi motor?
i have a error e7 on my fiat 500 scooter looks like when changing the tire i cut the wires some how. how to fix.
I’ve broken the same wires, any extra info on fixing that?
Good video. Please what of Error 6
Hi, thank you for the video. Where can I get a stand to place my motor while servicing like the silver one you have?
thank you kindly for your timely video. I have the same tester and will now go and put it to use. my project involves 4x 350w bldcm hubb motors. am I able to communicate with you as I go along please?
Nice work.
Thank you! Let us know what ideas you have.
I have the same errkr on my vsett 10.. Would this process be the same to fix it?
Nice!!! Thank you!!!!!!
No problem
Where can we get a hall sensor meter?
Our cycle is a 26 inch bicycle.
you mean the hall sensor pcb?
Nice video! Do you have any fixes for error 6?
yes error 6 is battery undervoltage, its possible to fix, check out this video: ruclips.net/video/Tnrttq77JjQ/видео.html
Hi just wandering g I have error e7 on my kaabo mantis 10 Pro lite and acceleration slows whe this happens any ideas
I have this error 7 with yanked out motor wire. Did change all halls, checks wires, but error is the same even with totally new motor wheels.
Thank you. I am currently stranded out 6 miles from home. And I ran into this error. I had some issues with my intertube. I replaced the tire and intertube, but it's so hard to get the tire back on the rim that I ended up putting a hole in the new tube. And I did the same thing again. Then .... I was running into the store to grab a 12" bicycle tube. I came back out to find this error e-007. Then it went back to normal as no error while I was fixing it. Then when I had everything back together, it went randomly error 7 and normal and error 7 then finally got stuck on the error.
Check the motor connector, it may not be inserted properly
This might be the problem I have for my Gyrocopters plaid because every thing works normally when I turn on zero start and push the throttle the motor goes for a sec then e16 pops up on the screen and motor hall anomaly keeps popping up on the app but I don’t have the right tools to open up the motor to check
Is it 60 degrees or 120 degrees hall sensor
Hi I got e7 is that the same thing as this video and my scooter is aovo pro
Motor error
Got same error on the same scooter, replacing motor did not helps.
Hi, question: for my scooter, the motor won't turn smoothly, it is as if something is restricing it. I opened the same way as yours but there is no burning smell or parts fallen appart. The scooter was working fine until I rode it a few minutes on rubble (it was a rough surface) it then just lost power. It's turning on and off, battery indicator is working and when I press the electric brake it restricts the back wheel even more. It's just the acceleration is not working. Please advice:(
I have the same problem my motor wont turn smooth . it is just like something block it . I also open it but nothing to see .
I already order 2 motors from zero 10x becouse the original models are shit . upgraded motor type 3 is much better .
now I only hope that my controller is not damage becouse off the stuck weel .....
@@bjornvanoppen Hello
Why doesn't the front wheel go on the go when my dual mode switch is just spinning or if I push, I can go fast with the rear, front doesn't work!
@@jozsi3534 did you fix this issue?, I currently have the same one
@@jorbbe9118 usually means one of the controllers burned out.
Hi!
I just realised your middle sensor in red, the 2 others in blue, so the middle one may not be the same...
I replaced it, and still have Error E07...
Could you give me all three sensors Part Number please...?
Sorry we don’t have it, your throttle has a hall sensor too try to change your throttle
The rear cable also becomes very hot and wheel jams... Some hub motor have a different hall sensor in the middle than the 1st and 3rd.. I think it's the case for the Zero 10X 48V 1000W hub motor, and I must have installed the wrong one..
I don't have the tools to do this and I just got mine yesterday
my zero 9 has a error 07. but if i disable the kick start is working. any suggestion? its gone before but after i charge it. it come back again
Motor error. Is yours a zero 9? From where
Can anyone tell me the part number for the motor hall sensor? I think it's 41E, but not sure. Can I install a 41F instead? Thank you
Cordial friend greetings, can you help me with my ZERO 1OX I have a problem at times when actuating the accelerator does not work and on one occasion going up a hill I braked and at the moment of releasing the brake the scooter was pushed and when actuating the accelerator again did not respond The LCD screen did not show me any error and then while I was at home when trying to enter the menu, the code 7 appeared, which is a fault in the engine, immediately turn off and turn on again, this time it did not appear again, I went out to drive it for a while using the dual motor And in turbo and has not reappeared. I appreciate your help informing me why this is due
yes error 7 is motor issue, its possible to fix, check out this video: ruclips.net/video/Tnrttq77JjQ/видео.html
I have a microgo m8 e scooter and when i am driving it it slows down or it turns off automatically and shows on the screen E7 .How can i fix it?
Same problem with same scooter here
@@aodbo2lol355 how are you going to fix it?
@@gersi1178 I haven’t yet , I might take it to an e-bike store
Do u guys find out how to fix it if so can you let me know
I've had the same problem for over a year on the same scooter, attempted to find the problem once before and took the scooter apart, but didn't have the melted solder issue like these guys, don't know what it is, might try looking again and getting a multimeter to test each hall sensor as maybe one needs replacing in comparison to resoldering
Hay can you halp my i have zero 8 error e0 what could be the reason thanks 🙏
It’s not a big issue. Error 0 just turn off and on and it’ll go away
@@FalconpevSg do you know the cause for the issue?
Hi I recently had my charger port blown out(fire) im wondering if I replace the port myself will it sort out the issue or nah? because since it burnt out the scooter does not turn on anymore.. So is that an issue with the port or do I need to send it off for repair/replacement?
Well in my example I was a moron and i touched the charging port with metal pliers and it shorted out my zero 9 but when you unplug and plug back in the wires where the battery is located it should turn on fine... I also replaced the charging port cause it was useless after that.
Thanks my scooter E7
my vici escooter is coming up e6 on screen and will not work it turns on but wont work error code 6 can someone please help me its a VICI
Is that the front tire or back tire
I can't find where this white wire goes please help
White wire goes to one of the pcb board
I have a evercross ev08 it's my daughters I'm going through chemotherapy I really need to fix it for her I've repaired all broke wires I just have this white one and there is no place I can see where it came from
Can you show how to waterproof inokim OXO, since it's near to be rainy season?
I have E1 error also broken throttle? Problem connected ??
I have a LH-100 display with a 1000 watt 48 volt motor. But it gives me error 7 with and without hall sensor connected. I checked from loose wires but couldn't find one. It runs very bad til im at 20 km/h than i can go full throttle without problems to max speed. If i do to much throttle before i reach 20 km/h it goes crazy and stops (breaks with shocks) and i can re-throttle and it'll work. But if i give to much gass it will kick out again. This is only before i reach 20km/h
Anyone knows a solution?
Please help.....
Your phase wires may have a problem. You can check your phase wires using this video.
@@FalconpevSg Ok i will check. Thanks!
Did you solved this problem? Got same with my scooter
Anyone know how to fix e1 message
Ho do you know something about e9 ?thanks
I just spent $1429 to repair my Wolf warrior x and when They shipped it back to me the display has read error 07 ever since I turned it on after receiving... Seems like after spending $1429 to have it repaired I shouldn't have to deal with this problem !!! Wtf?
It’s a simple connection issue. Just make sure your motor connection is plugged in properly
I have F7E scooter.im having an Lcd issues thats wat the customers service told me,there sending me a new1 Lcd.watbto do?
Tia Guerra we aren’t familiar with the F7E??
My kugoo s1 pro has a m error light on ( I assume it stands for motor) it works then randomly stops accelerating to continue accelerating you have to let go of the throttle and press again for it to accelerate could u help me resolve this issue
Best to ask your seller. Every scooter has different error codes and fault codes
Sound alike a controller issue. Did you ride in the rain recently ? (When you noticed the issue)
@@jordaneromosele7678 I haven't road in the rain but the previous owner did
The controllers may have to be replaced. Happened to my wolf king yesterday. The scooter is so powerful so the issue of it moving on its own full blast when it’s on is so dangerous.
Why you need to cut open all wires).Just open motor and fix the problem even all cables are connected to controller..is that possible?iv got error 7,but when I restart the scooter it disappeared and working properly...One's i get completely black out,no power suddenly. He doesn't even charge. But after 10 minutes, he just run again, without problems. Do you know what's happening????
Restart? How do you restart a Zero scooter??? I need to know this. Thanks.
Could you do repair on battery pack video. thanks
I took my zero 9 to a place and the guy put a multimeter on the chaging hole and something exploded. Now It doesnt start. What could it be?
He must have shorted it by accident. It’s not a big problem. You just need to open up the deck and unplug and plug in the yellow battery connector. It should work again. But the charging port may be burnt and you may need to change the charging port
@@FalconpevSg thanks for answering, I will check some of your videos and try it.
Do you know something about error003?
The front wheel doesn't go when I switch to dual mode, just the rear wheel! Help
What model scooter?
@@FalconpevSg Zero 10x 60v 21ah No error is displayed
What could be the problem?
Zero 9 with remote immobilizer activated. Everything was working fine for several months but now at 4:30am i was awaken with beeping + locked sounds , throttle shows E 06. Whats this please help? I need to go to work in 30 mins :(
E06 is battery under voltage
What’s error E0
My kids electric scooter says E7 how to fix
Check if motor cable melted
@@FalconpevSg🗣️I WATCHED THIS VIDEO . Y👤U SH🟢ULD SHOW THE RESOLDING PROCESS . ACTUALLY , SHOW Y👤U RESOLDING . I AM DEALING WITH THE SAME E 7 ERROR .>🎤🛴
How to soft error 22
How about an "Error 01" on a Hiboy S1?
sorry dont know what that is
red one is next , why not check all ? 3:52
Hi I have error e6 anybody fixed?
yes error 6 is battery undervoltage, its possible to fix, check out this video: ruclips.net/video/Tnrttq77JjQ/видео.html
How to fix a error E-09
joyor 9 wont power down, no error code
physically disconnect the battery
I am worrie cus it’s only been a day and it has already an error
What error
I have e10 was error 7 it its from motor also
e10 is communication error between lcd and controller. Check out this video to solve most of the error codes: ruclips.net/video/Tnrttq77JjQ/видео.html
If anyone has insight on how to fix a E 10 message (error 10), please share!
I’m still looking myself