For 9 years I reloaded with these kits. I immediately made better than factory ammo. I never had a single problem. I had many many enjoyable nights as a teen loading with these wonderful kits. In time I learned to use mild loads so my brass wouldn’t stretch & flow as much. I have upgraded my gear for greater precision & accuracy. But truth be told, I don’t honestly load any faster as I spend way more time on precision case work. It’s been a rewarding enjoyable lifelong hobby & I have my Dad to thank for introducing me to it.
Its good for me to do each step by about 50 catridges at a time and and work em up like that. I love these Lee Loaders because I don't have much money to invest in a serious set up or space for it either, so these things are great!
You might mention that the resizing die only resized the case neck which means if the round was fired in a rifle with a chamber slightly larger then the rifle you plan on shooting the cartridges in, you'll need a mallet to beat on your rifle to chamber the round. In 1982 I was 10 years old and my Dad bought me a Winchester 94 trapper 30-30. I was going to go deer hunting with him for the first time. He had boxes and boxes of 30-30 brass that had been fired in my uncle's rifle. I sat and watched as he reloaded those cartridges for hours. We went to the deer woods a day early to sight my rifle in. I loaded the rifle and worked the lever to chamber a round. The bolt wouldn't close all the way. After much pounding on the lever the bolt finally closed. That rifle really kicked when I was 10. He also reloaded 243 Winchester for use in his rifle. He didn't seat the bullets deep enough so the bullets touched the rifling when he chambered a round. When he unloaded the rifle it pulled the bullet out of the case and spilled all the powder in the action. We didn't have a cleaning rod so instead of being in the woods at the break of dawn opening morning we were driving to Walmart to buy a cleaning rod. It was always something. I didn't kill my first deer until I was eighteen and old enough to hunt by myself although Dad took me every year.
I love Lee Classic Loaders. Over the years, they have made kits for pretty much every cartridge, but unless it's in common use, you need to browse the auction sites for the out of production kits. These kits neck size rifle cartridges. As such lubrication isn't required. However, I will say that lubrication is helpful, always. Since these kits are intended for "one gun only" reloaders, trimming isn't mandatory. However, trimming to proper length is always a good idea. Lee makes caliber specific trimmers for a couple of dollars. Use is straightforward and relatively easy. Lee also says "bolt guns only". Personally, I find that they are quite fine with single shots and lever actions as well. Pump action may or may not work, depending upon the amount of leverage that particular pump has. Of all the action types that will show problems with these kits, semiautomatic rifles are the ones most likely to have failures to feed. I do have some friends who say these kits work for them, but percentage wise, the odds are against it. Pistol cartridges don't seem to have any preference. Typically, most can load a box of 50 per hour. That's a bit more than a minute each. Sounds fine to me. If you stick with the powders and charges listed in the kits, the included dipper is fine. If you want to use an unlisted powder, you need a loading manual, and a complete dipper set - or you need a set of scales. Proper technique with the dipper will give + or - one tenth of a grain, which is the same level of accuracy as an electronic scale. Proper technique means pushing the base of the dipper into the powder and allowing the powder to flow over the rim to fill. Level off, and done. Using the dipper to "scoop" it full of powder will result in much more variation, and is probably why some don't like the dipper technique. My first loader was a Lee Classic. I love them.
For those who want to reuse their brass, I would recommend getting a micrometer, measure the overall length of the case before you install the new primer, powder or bullet. Its important to keep the overall case length to the same length as an unfired case. If you find the case is longer, buy a case trimmer, set the trimmer to trim to the length of an unfired case, trim the case, check it with your micrometer and then begin your reload. For those who want shiny brass, a case tumbler with corn husk mead will bring them out like new.
Nice introduction to Lee Loaders. I had one years ago for 12 gauge shotgun, and thinking of getting one for .223. I think you could cut your time and find it more satisfying by having either a solid bench that doesn't vibrate and bounce, or get something heavy like a piece of steel or scrap of granite counter top or even a concrete paving brick to use as an anvil. Put a thin foam pad under it. That'll give you a solid surface to pound on. Less noise, vibration, less things jiggling off the bench.
Javier Fauxnom I'll pound it on my head, that's pretty hard...lol Seriously though, I have a 50 pound steel weight I could use as an anvil, just didn't have it when this video was made.
In time you will need to re size and cut your case to proper length other wise it won't camber . Lee loaders are awesome and serve a purpose for some who just starting out, but eventually you will need other tools to get the job done . Depends on your shooting , all in all a very enjoyable hobby . Thanks for your video.
Yup, I think I I have maybe reloaded the same 30-06 casing twice. It is definitely a limited application and not meant to be a high volume reloading tool. Thanks for stopping by ;-)
As far as using this at the range is a very good idea especially when you forgot the rest of the ammo and only have one case but not when it costs about the same as a die set for faster reloading. I just wish they made one on 40 S&W.
Necessary tools and materials: Block of wood, rubber hammer or mallet, spent brass and loader kit. Now THAT is my kind of reloading kit. I have been looking at Lee press kits and they seem a bit overkill, and unnecessary unless you want perfect match bullet setting. They're over the top for my budget, mil-surp plinking needs.
I started with a RCBS single stage press just to learn and get comfortable with reloading. I have a Lee 4 hole turret press and it is just right for how much I shoot. I had a Lee progressive press but it was too cumbersome to use. If you are not a competitive shooter I recommend a Lee 4 hole turret press. You can use it like a single stage if you want. The turrets make changing dies so much more convenient.
I have only reloaded about 50 rounds, and have not had primers go off on me, but I am sure it is probably just a matter of time. I use Reloader-7 powder with 150 grain sierra soft tips. I have had good and consistent results with that configuration. Hope that helps.
I love Lee stuff. It is a good value for the price. I did have a problem with a set of .40 cal bullet molds, but Midway exchanged it for me no problem.
I figured out a way to speed up depriming . I put deprimer on top of my vise that was open large enough to allow spent primer to fall out then i put a small catch pan underneath it to catch them. I can go through 50 cases pretty fast. It works really quick for shotgun too.
Thanks. You can start out cheap witht he Lee loaders and when you decide to get more into it, you can keep the Lee loaders as backup equipment or to take to the range for experimenting.
@@namelessisepic I used to not clean the brass if it was not too dirty or full of dirt if I picked them up from an outdoor range. They worked fine. Now I clean all my brass just because I have a tumbler, otherwise I would just rinse them with some water and let them dry out if they are dirty.
Cool ! Thanks, I've often thought about trying a bi - pod for my rifle. I have a Vanguard in 3006 , I'm not too sure if it would be a good idea because of the recoil. That 243 with the bi- pod did real good. That wind is something else ! Good shooting ! I'm a deer hunter too , it's so much fun ! David .
Thanks. I thought about buying a set of dies for it, but I don't plan on reloading a lot of 30-06, so I figures it was a good round to get a Lee Loader for.
Quick question: how does this work with 150 gr. Cast bullets using one of the Lee molds, when seating the bullet? Does the tip get damaged or does the tool push on the ogive of the bullet instead?
I'm not sure how it does with cast bullets. The recess of the bullet setter does look like it has some curvature in it instead of just being conical, so I can only guess that it can push on the ogive depending on the shape of the bullet used.
I was just in a discussion with a new 308 rifle owner that said at 50 cents a round storebought he couldnt make reloading pay. I think I will send him this video link so that he can talk directly to you and the other reloaders for the specific advantages of hand reloading.
Welcome aboard shipmate😄 When I first created my account, I just wanted to use it so I could comment on other videos. Never intended to post anything myself. I tried several other handles but they were already taken and this one was the first one I tried that wasn't taken.
LOL...I forgot to put that in. $30 for 100 bullets so 30 cents there, $30 for a pound of powder and each round takes 43 gr, so about 18 cents there, a primer is about 1 cent. Total is 49 cents a round. The cheapest factory stuff I found is $17 for 20 rounds or 85 cents a round. a 42% savings!
And 7 years later, the prices have gone down on the bullets and powder! Depending on the powder type but there are dozens of good gun powders to choose from listed in the reloading manual.
The chances of setting off a primer is low unless you either misfeed the primer pocket and really pound on the casing. Also (less likely) if you use the de-capping tool to try to set the primer. I might do a "worse case" video to show what , if anything, will happen if a primer gets set off by doing it wrong.
@John Beige I have only used tis set about 50 times and never had any issues. I don't reload 30-06 much. I do know people who have used these kits more and have never had any issues either. Check out logcanimlooms channel. He has a few videos using these kits.
I can't remember how much powder I used, but primers are about one cent, bullets are anywhere from 18-25 cents each and I think I used about 17 cents worth of power. So one reloaded round costs about 36 to 43 cents each. New factory rounds cost about 85 cents to $1.25 each. pretty decent savings if you shoot a lot, but for convenience, you are probably better off buying factory ammo.
7:02 Well just the common ones. I hear they used to be in everything from .32 ACP to 8mm Mauser but they have been condensed to the common cartridges like 5.56, 9mm, and .308 for example. Strangely, they still have kits for .303 British.
When I first started reloading, I looked into this kit but the single stage press is just that much faster. I would see if you were out in the field, it would come in handy. Good vid.
Thanks for the reply and the link for the video . The factory ammo seems to be about right as far as trajectory at 40 yards . It looks like your reload has a little more velocity than the factory. I would think your reload round is still on the rise at 40 yards. What powder did you use ? Are those Berger bullets ? Shooting off the tree and having those groups like that ain't bad at all. I'm new to reloading , I haven't reloaded anything yet , but I do have everything I need . I'm waiting for hunting season. I'm using a RCBS partner press that I have only used to set up my dies , straighten case necks and make dummy rounds to find max lands to bolt face to make bullet jump measurements. I almost bought the Lee loader , the Lee reloads and shooting off the tree is impressive. Thanks , David
David Ray My pleasure! I think I used Reloader 7 powder. I think the bullets were Sierra 150 gr soft tips. I can't remember. I need to find a longer shooting range to put the 30-06 on paper with a more steady rest to see just how accurate the rifle is. My buddy has some property about an hour from me, maybe I can take it out to his place and try.
I used to get primers from my local gun store, but they have been out for years. Maybe try midway usa. You can get bullets from RMR Bullets. They have decent prices.
I don’t have an unloaded cartridge that hasn’t been fired to calibrate mine, but I have access to precision measuring instruments. A factory loaded round measures around .334. Could someone let me know what the unloaded neck diameter is?
RainbowCupcakez 69 There really is no standard unloaded neck size. It depends on the chamber size on the rifle it was fired out of as the neck will expand as large as the size of the chamber. Is that what you are asking?
saltyshellback not exactly. I’m reloading some cartridges and I have the neck diameter the perfect size, but the bullet is loose enough to spin , but not loose enough to come out if I pull on it.I suppose I just need crimping? If not I could set the resizing die a few thousandths smaller.
RainbowCupcakez 69 some casing wall thicknesses may be thinner than others or have thinned out over time, so the OD of the neck may be right, but the ID may be larger than nominal because of a thin neck wall. Do you know how many times those casings have been fired?
RainbowCupcakez 69 I personally would go ahead and crimp it a little more to keep the bullet in place, but I'm not a competitive shooter. I guess it depends on whether you are trying to squeeze all the accuracy out of your rifle or just want to hit a target at 100 yards with decent precision. Meaning if you need to crimp the neck smaller, a "purist" may say that the bullet jump from the neck being 0.001" too small can cause inaccuracy. However if you are hunting, it should be accurate enough up to 200 yards. I can hit an 18" target at 300 yards with the reloads I made with the Lee loader. Some of the bullets do seem a bit loose like you described. I am sure the accuracy can only be better at 200 and 100 yards.
I would be glad to give him any information. Hand loading is not for everyone...some people are best to buy pre-made ammo either because of time constraints, space to keep stuff, or are just not that mechanically inclined.
Great video thanks can I load 3006 rounds for a M1 rifle or any semi auto rifle or is it just for lever guns and bolt action rifles. It seems like a strange question. But I was looking at a different channel. They stressed no semi autos. Let me know. If possible I would really appreciate it.
I have only used this Lee loader for my bolt action 30-06. I am not sure why they would not recommend it for semi-autos. All I know is that it only resizes the neck, so you should only use the reloaded cartridge on this same gun that you previously fired it our of because the case body may be a bit larger for a different chamber. other than that I am not sure why it would affect a semi-auto gun. could be that a semi auto may not have enough spring power to push the cartridge into battery if the case is a bit oversized.
One more thing. Do you trim the and debure the cases. I new to this. I have a friend who reloads for me. 7.62NATO 3006, Marlin 444 and 8mm. He's getting on in years. I purchase 5.56 and 7.62x 39. I served thirty years in the United States Army almost twenty in the Ranger Regiment.I retired in 2010. I'm disabled my kids are grown and my wife passed September 2018 at 54. I'm 57 so I do stuff to keep busy so I don't go crazy. Should I just get a press and the dies for the larger calibers. That might be the way to go. Sorry to ramble. It's not money I just want to do it right. Thanks in advance for any advice you can offer.
Honestly it’s beyond me they want a press for 223 Remington for 300-500 dollars and the entire setup press, gunpowder, shell polisher, for like 1,100. I haven’t even seen a 30-06 press nor do I have the room/money for one. These work just as fast if you get a good rhythm
I do not reload rifle, it is the whole opportunity cost issue that involves reloading rifle. Pistol on the othter hand mak more sense to me. I just do not shoot enough rifle for me to justify it. I agree with you Salty, in a SHTF/WROL situation, it does make sense. I do have all the components and dies to reload .223 if needed, just in case.
Everybody wants to go fast.....this little reloading tool kit is designed to work up a few rounds for accuracy improvement. It is meant to be used for a more meticulous, slower type of loading to perfect a load that will improve the accuracy of your rifle or handgun. The press that he has on his bench is designed to then "crank" out or "mass" produce new cartridges. So yeah, take this kit to the deer camp or add it as an extension in your garage with your other progressive loading press but by all means slow down, relax and enjoy the process. Everybody wants to go too fast and that is a recipe for error which in the handloading/reloading game can be dangerous. Take your time and make good accurate bullets. With today's ammo prices and shortages, you can once again SAVE a good deal of money by reloading. I enjoy using my lee kit in the 243 Winchester. It makes good ammo that is safe so long as you follow directions, pay attention, and take it slow.
what's the powder that you use? i'm using IMR 4350 w/ Sierra 150gr bullets. using the Lee Classic Loader. load out is 54gr at 3.25OAL. i'm new to reloading and i'm kind of scared of pulling the trigger on the 1st reloaded round. also i've had a few primers go off on me while using the "tap in" method, this is pre-powder load. ever run into that problem? i have found that 4 medium taps generally seats the primer.
But how do you use the same dipper for different powders since they do not all occupy the same volume. Is the one dipper calibrated for a specific powder thats noted on the instruction sheet?
I don't use the dipper that came with the kit, so I am not sure what powder it is for. I have a separate powder dispenser and I meter out the weight specified for the powder I use.
I bought the Lee hand press.? Must more easier to reload with. No hammer needed.? The Kit is worth the $50.00 Bucks. Plus you need a set of Reloading dies.? For the Caliber you intend to load with.
I bought 30cal .308 dia. 175gr hpbt, SIERRA and borrow a friend 30.06 lee loader but it didn't go down enough to set on the brass, is it some thing wrong with bullet or the lee loader? Original brass from barnes. What am I missing? Do i need to get the .308 lee kits?
How many scoops for Winchester 760 gun powder? Can I just use one.... Also my Hornady 308 bullets just drop through the casing..... just bought this kit and wondering what I am missing?????????????
+Levi Tkachuk As far as powder, I have not used Winchester 760. You might try to look up the powder charge at handloads.com. I'm not sure why the bullets fall through. Could be you have some thin casings or undersized bullets, or oversized die. If you have a dial caliper (or digital caliper) you can measure the ID of the case mouth and the OD of the bullet to see if you have an interference fit. That means the ID of the case mouth is the same size or 0.001" smaller than the bullet diameter. This will also let you know of you truly have a 0.308" diameter bullet or not. Hope that helps.
I want to use this for 300 aac is there any way I would be able to just using like the 308 and modify it somehow? Like a metal spacer or something to take up the space wile it still sizes the neck?
I don't know much about the 300 aac. But if the neck size is similar, they you could give it a try. These dies do not do a full case resize, so if you can get the case to go in all the way to the neck, you could use a dowel or something to push the case past the bottom of the resizing die.
I use to use a led sled to sight in and shoot for groups but I learned real quick that was not good for scopes and tight groups. The sled is too rigid for the fluid motion of recoil . Sand bags are the way to go. You probably know this already but if not , use sand most definitely. . If you make another video of the same ammo and reloads at 100 yards , I'd like to see that ! Thanks again , David
David Ray Here is my most recent day at the range. I was shooting my nephew's guns. I didn't change the reticle settings, just compensated for where the crosshairs were aiming in relation to the actual shot placement. That way, I don't mess up his shot placement. ruclips.net/video/a8Ko3CUPjqw/видео.html
what happens if I have a lot of casings that have indented case mouths? As in, maybe it was deformed during ejection or otherwise? Will this still get them back into shape? Same issue with my .223 casings?
It depends on how badly they are kinked. You should be able to reform most dents with the de-priming punch. Just work the punch into the case mouth slowly if it is a tight fit.
Yeah, I was thinking that might do just fine. I actually just checked out about 25 .223 cases in the pile and I only saw one, maybe two that I may just have to keep on the side or discard. That's really not too bad I suppose. All my .30-06 looked pretty nice though. Thanks a lot for the quick reply. I actually just ordered one for .30-06. Looking forward to using it! :)
Good deal! The Lee Loaders are fine for small quantity reloading and they help new reloaders understand the process. I have a progressive press for my higher quantity calibers like .40 and .45, but I only reload like 10 to 20 30-06 per year, so it is not practical to get something that can crank out hundreds per hour....lol
Thank you.. very informative. This got me started. My only question is ... I am never over in length but under... are there issues with being under ? We are not talking a lot.
As far as being under, I do not know of any issues as long as the overall length (OAL) of the cartridge is within specifications. Too long and the cartridge will not chamber. Too short and there is a phenomenon called "skipping" that could cause inaccuracy, albeit most of the time negligible unless you are a competitive shooter or something. Usually after a few reloads (could be 2 times, could be 10 times), the case neck will expand due to the explosive pressure, so just keep an eye on the case length. I only have about 2 reload cycles on my 30-06 cases and they are still in good shape. Hope that helps :-)
H.D.Instrumental I am not sure. Sorry. Try handloads dot com. They have a lot of good load data. I usually reduce their load data by at least 10% on my first loads and check to make sure the load is not a squib load after the first shot (check the barrel to make sure the bullet made it out).
I am not sure. I looked at miswayusa and e-bay but did not find it. You may want to do a youtube search for lee classic loader 7mm mauser to see what other people came up with. Hope that helps.
I think if you used the primer/ case brush to clean the primer home,it will go in much easier. I use to reload with my Father,all RCBS equip. When he stopped hunting it all got sold, damm I missed out on ALOT of tools.dies ,etc. I may try and buy a couple of these and see what I think. ''Hey how much would ya say it cost ya to make a box of shells ?
I have tried, but it depends if you have a bullet with a crimping groove or not. I have not had good luck trying to crimp on a bullet without a crimping groove. You have to be careful not to bend the shoulder of the round when trying to crimp that way. Hope that makes sense.
edward guillo This kit only resizes the neck. It is not meant for high volume reloading or for use with multiple guns. There is a chance the reloaded rounds won't fit anything besides the last gun it was fired from due to the chamber size.
you can always purchase a Lee case trimer. it is used to resize overall length.. you should get one. cheap and efficient. I resize all my brass for over all length.
Yes, lube the case. It will make it easier knocking the case out and priming in the same motion. He doesn't know this so he says "it doesn't work for me" and knocks the case out then primes it.
So the video he mentioned of "Logcabinlooms" using the lee loader was made private or removed, however I did you one betta. Much Mo betta. Here's the inventor of the product showing his technique. Slow is smooth and smooth is fast, and he's pretty damn smooth people. Link's below. ruclips.net/video/UeEl9wZyabc/видео.html
@@saltyshellback No, thank you. I've been weighing the pros and cons of reloading for just a couple calibers and your video helped me make my decision. I appreciate the time you took to make a video on the products. I'll be picking up a classic loader kit and the powder measure kit this week. Have a great day.
zed zardoz The bullets cost about 17 cents, the powder is about 5 cents and the primer is about 4 cents, so a total of about 26 cents per round to reload.
saltyshellback How are you figuring your powder charge cost? Also, are you buying those bullets by the case or something? Just seems a little low cost-wise. $23/lb powder comes out to $0.16 per 50gr charge, and a lot of quality 30cal projectiles seem to run around $0.25/ea. But, I'm not buying bulk so perhaps that's my problem lol.
You need to use the yellow side of the hammer and don't hit as hard you will have much better results. Don't ever take the case out of the die to seat the primer😮😮
Question: On amazon (as well as some youtube channels) it says that lee loader only resizes the neck and therefore it is suitable only for bolt-action rifles. How safe is it to resize only the neck? I am only concerned with the safety as I have only bolt-actions anyway.
Pirouz Pourdowlat It is not a big deal to just resize the neck. As long as there are no cracks in the casing, there should not be any safety concerns. The only catch is sometimes if you shot the round out of one gun and don't resize the whole case, you may not be able to chamber it in another gun that may have a smaller chamber. Other than that it should work in the same gun.
Been resizing my ammo using this systems for many many years. I only shoot bolt action rifles, so I can not comment on semi autos. Most semi autos would require a crimp. but I never had a problem in my bolts. All rifles produce sub moa or half moa. take the time to inspect all brass for defects before reloading. One thing. some cases such as 270win have a habit of getting larger in diameter,, there fore every time I resize the brass I always check to see if it chambers in my rifle before I proceed to reload primer and powder. otherwise.. no problem. I shoot about 2000 rounds per year.
For 9 years I reloaded with these kits.
I immediately made better than factory ammo.
I never had a single problem.
I had many many enjoyable nights as a teen loading with these wonderful kits.
In time I learned to use mild loads so my brass wouldn’t stretch & flow as much.
I have upgraded my gear for greater precision & accuracy.
But truth be told, I don’t honestly load any faster as
I spend way more time on precision case work.
It’s been a rewarding enjoyable lifelong hobby & I have my Dad to thank for introducing me to it.
Yup. To me reloading is relaxing 😄
Its good for me to do each step by about 50 catridges at a time and and work em up like that. I love these Lee Loaders because I don't have much money to invest in a serious set up or space for it either, so these things are great!
MrHondaguy1 True that! I don't shoot much 30-06 so this set is just right for me.
ricarica 7.65
454 is 5
You might mention that the resizing die only resized the case neck which means if the round was fired in a rifle with a chamber slightly larger then the rifle you plan on shooting the cartridges in, you'll need a mallet to beat on your rifle to chamber the round. In 1982 I was 10 years old and my Dad bought me a Winchester 94 trapper 30-30. I was going to go deer hunting with him for the first time. He had boxes and boxes of 30-30 brass that had been fired in my uncle's rifle. I sat and watched as he reloaded those cartridges for hours. We went to the deer woods a day early to sight my rifle in. I loaded the rifle and worked the lever to chamber a round. The bolt wouldn't close all the way. After much pounding on the lever the bolt finally closed. That rifle really kicked when I was 10. He also reloaded 243 Winchester for use in his rifle. He didn't seat the bullets deep enough so the bullets touched the rifling when he chambered a round. When he unloaded the rifle it pulled the bullet out of the case and spilled all the powder in the action. We didn't have a cleaning rod so instead of being in the woods at the break of dawn opening morning we were driving to Walmart to buy a cleaning rod. It was always something. I didn't kill my first deer until I was eighteen and old enough to hunt by myself although Dad took me every year.
Yup, live and learn ;-)
Sounds like you’re a lucky guy to me, I’m hoping to get my first deer this season at a young 34.
I love Lee Classic Loaders. Over the years, they have made kits for pretty much every cartridge, but unless it's in common use, you need to browse the auction sites for the out of production kits.
These kits neck size rifle cartridges. As such lubrication isn't required. However, I will say that lubrication is helpful, always. Since these kits are intended for "one gun only" reloaders, trimming isn't mandatory. However, trimming to proper length is always a good idea. Lee makes caliber specific trimmers for a couple of dollars. Use is straightforward and relatively easy.
Lee also says "bolt guns only". Personally, I find that they are quite fine with single shots and lever actions as well. Pump action may or may not work, depending upon the amount of leverage that particular pump has. Of all the action types that will show problems with these kits, semiautomatic rifles are the ones most likely to have failures to feed. I do have some friends who say these kits work for them, but percentage wise, the odds are against it.
Pistol cartridges don't seem to have any preference.
Typically, most can load a box of 50 per hour. That's a bit more than a minute each. Sounds fine to me.
If you stick with the powders and charges listed in the kits, the included dipper is fine. If you want to use an unlisted powder, you need a loading manual, and a complete dipper set - or you need a set of scales. Proper technique with the dipper will give + or - one tenth of a grain, which is the same level of accuracy as an electronic scale. Proper technique means pushing the base of the dipper into the powder and allowing the powder to flow over the rim to fill. Level off, and done. Using the dipper to "scoop" it full of powder will result in much more variation, and is probably why some don't like the dipper technique.
My first loader was a Lee Classic. I love them.
Yup! The Lee Loader kits are good for trying out different recipes at the range too.
Yup. I am slowly building my collection of reloading equipment and I think the Lee loaders are a good low tech backup every reloader should have.
For those who want to reuse their brass, I would recommend getting a micrometer, measure the overall length of the case before you install the new primer, powder or bullet. Its important to keep the overall case length to the same length as an unfired case.
If you find the case is longer, buy a case trimmer, set the trimmer to trim to the length of an unfired case, trim the case, check it with your micrometer and then begin your reload. For those who want shiny brass, a case tumbler with corn husk mead will bring them out like new.
Good tips. Thanks!
Nice introduction to Lee Loaders. I had one years ago for 12 gauge shotgun, and thinking of getting one for .223. I think you could cut your time and find it more satisfying by having either a solid bench that doesn't vibrate and bounce, or get something heavy like a piece of steel or scrap of granite counter top or even a concrete paving brick to use as an anvil. Put a thin foam pad under it. That'll give you a solid surface to pound on. Less noise, vibration, less things jiggling off the bench.
Javier Fauxnom I'll pound it on my head, that's pretty hard...lol Seriously though, I have a 50 pound steel weight I could use as an anvil, just didn't have it when this video was made.
In time you will need to re size and cut your case to proper length other wise it won't camber . Lee loaders are awesome and serve a purpose for some who just starting out, but eventually you will need other tools to get the job done .
Depends on your shooting , all in all a very enjoyable hobby . Thanks for your video.
Yup, I think I I have maybe reloaded the same 30-06 casing twice. It is definitely a limited application and not meant to be a high volume reloading tool. Thanks for stopping by ;-)
Very good for reloading very accurate rounds if you weigh the powder.
yup
As far as using this at the range is a very good idea especially when you forgot the rest of the ammo and only have one case but not when it costs about the same as a die set for faster reloading. I just wish they made one on 40 S&W.
Yup!
I have a Lee Loadmaster with over 150K rounds through it and love it! Great vid Salty!
Thanks! I don't plan to reload a whole lot of 30-06, but it's there when I need it.
Necessary tools and materials: Block of wood, rubber hammer or mallet, spent brass and loader kit. Now THAT is my kind of reloading kit. I have been looking at Lee press kits and they seem a bit overkill, and unnecessary unless you want perfect match bullet setting. They're over the top for my budget, mil-surp plinking needs.
I started with a RCBS single stage press just to learn and get comfortable with reloading. I have a Lee 4 hole turret press and it is just right for how much I shoot. I had a Lee progressive press but it was too cumbersome to use. If you are not a competitive shooter I recommend a Lee 4 hole turret press.
You can use it like a single stage if you want. The turrets make changing dies so much more convenient.
Excellent demonstration and tips, thank you.
My pleasure!
I have only reloaded about 50 rounds, and have not had primers go off on me, but I am sure it is probably just a matter of time. I use Reloader-7 powder with 150 grain sierra soft tips. I have had good and consistent results with that configuration. Hope that helps.
I love Lee stuff. It is a good value for the price. I did have a problem with a set of .40 cal bullet molds, but Midway exchanged it for me no problem.
I figured out a way to speed up depriming . I put deprimer on top of my vise that was open large enough to allow spent primer to fall out then i put a small catch pan underneath it to catch them. I can go through 50 cases pretty fast. It works really quick for shotgun too.
Good idea! Thanks!
I've loaded on a press for years, but to me this way is more fun. 👍
Hammer good! 😄
Yup. As time goes by, I want to get a set for every caliber I have as a backup and to take to the range.
Thank you for the great explanations, demonstrations, and costs... It helped a lot.
Thanks. You can start out cheap witht he Lee loaders and when you decide to get more into it, you can keep the Lee loaders as backup equipment or to take to the range for experimenting.
And for the up grade, I use a Sinclair Arbor press instead of the hammer. Also, a Winson bullet seater die. 💯
ok
Before using this kit do you use a cleaner of some kind? I have seen other people using a tumbler with polisher and walnut shells.. thanks
@@namelessisepic I used to not clean the brass if it was not too dirty or full of dirt if I picked them up from an outdoor range.
They worked fine.
Now I clean all my brass just because I have a tumbler, otherwise I would just rinse them with some water and let them dry out if they are dirty.
Cool ! Thanks, I've often thought about trying a bi - pod for my rifle.
I have a Vanguard in 3006 , I'm not too sure if it would be a good idea because of the recoil.
That 243 with the bi- pod did real good.
That wind is something else ! Good shooting !
I'm a deer hunter too , it's so much fun !
David .
David Ray Cool! Hoping to bag me a couple deer this year :-)
Thanks. I thought about buying a set of dies for it, but I don't plan on reloading a lot of 30-06, so I figures it was a good round to get a Lee Loader for.
Quick question: how does this work with 150 gr. Cast bullets using one of the Lee molds, when seating the bullet? Does the tip get damaged or does the tool push on the ogive of the bullet instead?
I'm not sure how it does with cast bullets. The recess of the bullet setter does look like it has some curvature in it instead of just being conical, so I can only guess that it can push on the ogive depending on the shape of the bullet used.
I was just in a discussion with a new 308 rifle owner that said at 50 cents a round storebought he couldnt make reloading pay. I think I will send him this video link so that he can talk directly to you and the other reloaders for the specific advantages of hand reloading.
Haha love the handle. Its been a long time since i got my Shellback card.
Welcome aboard shipmate😄
When I first created my account, I just wanted to use it so I could comment on other videos. Never intended to post anything myself.
I tried several other handles but they were already taken and this one was the first one I tried that wasn't taken.
@@saltyshellback I get that, but what you do may help someone like me. I just ordered my 1st Lee Loader for my 30-30.
LOL...I forgot to put that in. $30 for 100 bullets so 30 cents there, $30 for a pound of powder and each round takes 43 gr, so about 18 cents there, a primer is about 1 cent. Total is 49 cents a round. The cheapest factory stuff I found is $17 for 20 rounds or 85 cents a round. a 42% savings!
And 7 years later, the prices have gone down on the bullets and powder!
Depending on the powder type but there are dozens of good gun powders to choose from listed in the reloading manual.
Is there any chance of the primers going off doing this method? Great instructions and video. Thanks!
The chances of setting off a primer is low unless you either misfeed the primer pocket and really pound on the casing. Also (less likely) if you use the de-capping tool to try to set the primer. I might do a "worse case" video to show what , if anything, will happen if a primer gets set off by doing it wrong.
@John Beige I have only used tis set about 50 times and never had any issues. I don't reload 30-06 much. I do know people who have used these kits more and have never had any issues either. Check out logcanimlooms channel. He has a few videos using these kits.
Have you calculated about what it takes to make a cartridge as far as money. I really enjoyed the video and just ordered mine from amazon
I can't remember how much powder I used, but primers are about one cent, bullets are anywhere from 18-25 cents each and I think I used about 17 cents worth of power. So one reloaded round costs about 36 to 43 cents each. New factory rounds cost about 85 cents to $1.25 each. pretty decent savings if you shoot a lot, but for convenience, you are probably better off buying factory ammo.
7:02 Well just the common ones. I hear they used to be in everything from .32 ACP to 8mm Mauser but they have been condensed to the common cartridges like 5.56, 9mm, and .308 for example. Strangely, they still have kits for .303 British.
I'm sure you can find some less common sizes on ebay, but they may be a bit more expensive than a new set.
When I first started reloading, I looked into this kit but the single stage press is just that much faster. I would see if you were out in the field, it would come in handy. Good vid.
You can crimp your bullets in place by tapping it back into the sizing die after you seat the bullet.
Yup. you have to be careful though because it only resizes the neck so it can bulge the shoulder if you force the case into the resizer.
Picked one of these up for 9mm to do a review, but you beat me to it :-P
Can't ask for a better SHTF setup than a mallet and one of these kits!
if SHTF where do you think youre getting your components from?
@@JM-bl3ih my shelf ... been collecting and storing for quite some time now.
Do you ever have a problem with the neck not resizing properly? I got a lee reloader for my 30-06 and the projectile just falls in the case
Yup, sometimes I get a loose projectile, but nothing too bad. You may need to get a factory crimper die.
Thanks for the reply and the link for the video .
The factory ammo seems to be about right as far as trajectory at 40 yards .
It looks like your reload has a little more velocity than the factory.
I would think your reload round is still on the rise at 40 yards.
What powder did you use ?
Are those Berger bullets ?
Shooting off the tree and having those groups like that ain't bad at all.
I'm new to reloading , I haven't reloaded anything yet , but I do have everything I need .
I'm waiting for hunting season.
I'm using a RCBS partner press that I have only used to set up my dies , straighten case necks and make dummy rounds to find max lands to bolt face to make bullet jump measurements.
I almost bought the Lee loader , the Lee reloads and shooting off the tree is impressive.
Thanks , David
David Ray My pleasure! I think I used Reloader 7 powder. I think the bullets were Sierra 150 gr soft tips. I can't remember. I need to find a longer shooting range to put the 30-06 on paper with a more steady rest to see just how accurate the rifle is. My buddy has some property about an hour from me, maybe I can take it out to his place and try.
Where do u buy bullets and primers?
I used to get primers from my local gun store, but they have been out for years. Maybe try midway usa. You can get bullets from RMR Bullets. They have decent prices.
Yup. I plan to take it out this weekend to try our some 30-06 loads :-)
I don’t have an unloaded cartridge that hasn’t been fired to calibrate mine, but I have access to precision measuring instruments. A factory loaded round measures around .334. Could someone let me know what the unloaded neck diameter is?
RainbowCupcakez 69 There really is no standard unloaded neck size. It depends on the chamber size on the rifle it was fired out of as the neck will expand as large as the size of the chamber. Is that what you are asking?
saltyshellback not exactly. I’m reloading some cartridges and I have the neck diameter the perfect size, but the bullet is loose enough to spin , but not loose enough to come out if I pull on it.I suppose I just need crimping? If not I could set the resizing die a few thousandths smaller.
RainbowCupcakez 69 some casing wall thicknesses may be thinner than others or have thinned out over time, so the OD of the neck may be right, but the ID may be larger than nominal because of a thin neck wall. Do you know how many times those casings have been fired?
saltyshellback I fired them once. I can measure the ID, should I just make it exactly .308 or maybe .307?
RainbowCupcakez 69 I personally would go ahead and crimp it a little more to keep the bullet in place, but I'm not a competitive shooter.
I guess it depends on whether you are trying to squeeze all the accuracy out of your rifle or just want to hit a target at 100 yards with decent precision.
Meaning if you need to crimp the neck smaller, a "purist" may say that the bullet jump from the neck being 0.001" too small can cause inaccuracy. However if you are hunting, it should be accurate enough up to 200 yards.
I can hit an 18" target at 300 yards with the reloads I made with the Lee loader. Some of the bullets do seem a bit loose like you described. I am sure the accuracy can only be better at 200 and 100 yards.
I would be glad to give him any information. Hand loading is not for everyone...some people are best to buy pre-made ammo either because of time constraints, space to keep stuff, or are just not that mechanically inclined.
Thanks for the video! Gonna try it for myself.
Good deal!
If you use a flat patio cinder block on your bench. It cuts down on the vibration.
Meh, not too worried about the vibrations.
great tool to have if you in the wild , replentish your ammo in a few an keep going
It works.. Most things that are worth while take patience...
Yup, it's a good reliable method and just fine for ammo you don't shoot very often. Especially if it is more expensive like the 30-06.
Good job. Subscribed. Thank you.
Welcome aboard! 😉
Great video thanks can I load 3006 rounds for a M1 rifle or any semi auto rifle or is it just for lever guns and bolt action rifles. It seems like a strange question. But I was looking at a different channel. They stressed no semi autos. Let me know. If possible I would really appreciate it.
I have only used this Lee loader for my bolt action 30-06. I am not sure why they would not recommend it for semi-autos. All I know is that it only resizes the neck, so you should only use the reloaded cartridge on this same gun that you previously fired it our of because the case body may be a bit larger for a different chamber. other than that I am not sure why it would affect a semi-auto gun. could be that a semi auto may not have enough spring power to push the cartridge into battery if the case is a bit oversized.
One more thing. Do you trim the and debure the cases. I new to this. I have a friend who reloads for me. 7.62NATO 3006, Marlin 444 and 8mm. He's getting on in years. I purchase 5.56 and 7.62x 39. I served thirty years in the United States Army almost twenty in the Ranger Regiment.I retired in 2010. I'm disabled my kids are grown and my wife passed September 2018 at 54. I'm 57 so I do stuff to keep busy so I don't go crazy. Should I just get a press and the dies for the larger calibers. That might be the way to go. Sorry to ramble. It's not money I just want to do it right. Thanks in advance for any advice you can offer.
Honestly it’s beyond me they want a press for 223 Remington for 300-500 dollars and the entire setup press, gunpowder, shell polisher, for like 1,100. I haven’t even seen a 30-06 press nor do I have the room/money for one. These work just as fast if you get a good rhythm
Yup! For sure!
Where can I buy the shells primers and etc. a web site maybe
Gun stores usually will have what you need, otherwise Midwayusa.com will have what you need.
how can you adjust the bullet deep?
The bullet pusher stem has adjustable threads.
Yeah, I didn't know about Lee loaders until about a year ago, and I have been reloading off and on for about 25 years.
I don't know for sure, but the Lee loaders may come in those sizes. I have not hunted any deer with the 30-06 yet. I will bring it this weekend :-)
I do not reload rifle, it is the whole opportunity cost issue that involves reloading rifle. Pistol on the othter hand mak more sense to me. I just do not shoot enough rifle for me to justify it. I agree with you Salty, in a SHTF/WROL situation, it does make sense. I do have all the components and dies to reload .223 if needed, just in case.
Everybody wants to go fast.....this little reloading tool kit is designed to work up a few rounds for accuracy improvement. It is meant to be used for a more meticulous, slower type of loading to perfect a load that will improve the accuracy of your rifle or handgun. The press that he has on his bench is designed to then "crank" out or "mass" produce new cartridges. So yeah, take this kit to the deer camp or add it as an extension in your garage with your other progressive loading press but by all means slow down, relax and enjoy the process. Everybody wants to go too fast and that is a recipe for error which in the handloading/reloading game can be dangerous. Take your time and make good accurate bullets. With today's ammo prices and shortages, you can once again SAVE a good deal of money by reloading. I enjoy using my lee kit in the 243 Winchester. It makes good ammo that is safe so long as you follow directions, pay attention, and take it slow.
Meh, people can use it however they want. There is no one reason to own one.
what's the powder that you use? i'm using IMR 4350 w/ Sierra 150gr bullets. using the Lee Classic Loader. load out is 54gr at 3.25OAL. i'm new to reloading and i'm kind of scared of pulling the trigger on the 1st reloaded round. also i've had a few primers go off on me while using the "tap in" method, this is pre-powder load. ever run into that problem? i have found that 4 medium taps generally seats the primer.
But how do you use the same dipper for different powders since they do not all occupy the same volume. Is the one dipper calibrated for a specific powder thats noted on the instruction sheet?
I don't use the dipper that came with the kit, so I am not sure what powder it is for. I have a separate powder dispenser and I meter out the weight specified for the powder I use.
I bought the Lee hand press.? Must more easier to reload with. No hammer needed.? The Kit is worth the $50.00 Bucks. Plus you need a set of Reloading dies.? For the Caliber you intend to load with.
+MyREDTAIL Yup, good starter setup.
?
I bought 30cal .308 dia. 175gr hpbt, SIERRA and borrow a friend 30.06 lee loader but it didn't go down enough to set on the brass, is it some thing wrong with bullet or the lee loader? Original brass from barnes. What am I missing? Do i need to get the .308 lee kits?
I am not sure. You may have the 30-06 lee loader. Sorry I don't know what could be wrong.
I found out that it work for barnes only, not other bullet brand....thanks
Glad you were able to get it resolved. :-)
How many scoops for Winchester 760 gun powder? Can I just use one.... Also my Hornady 308 bullets just drop through the casing..... just bought this kit and wondering what I am missing?????????????
+Levi Tkachuk As far as powder, I have not used Winchester 760. You might try to look up the powder charge at handloads.com. I'm not sure why the bullets fall through. Could be you have some thin casings or undersized bullets, or oversized die. If you have a dial caliper (or digital caliper) you can measure the ID of the case mouth and the OD of the bullet to see if you have an interference fit. That means the ID of the case mouth is the same size or 0.001" smaller than the bullet diameter. This will also let you know of you truly have a 0.308" diameter bullet or not. Hope that helps.
So what bullets did you use and what powder? I’m new so the more descriptive the better, thanks
yodalover09 I use 150 grain jacketed soft point bullets and 43.8 grains of Reloader 7 powder. hope that helps.
saltyshellback awesome thanks, what primers do you use?
yodalover09 I buy the middle of the line primers like Federal or Winchesters. They cost about $30-$40 per 1000.
saltyshellback ok thanks
Is it cheaper to make the bullets than buy them
It depends on the kind of bullet. Cast lead is cheaper, but I can't make FMJ or jacketed hollow points at the moment.
I want to use this for 300 aac is there any way I would be able to just using like the 308 and modify it somehow? Like a metal spacer or something to take up the space wile it still sizes the neck?
I don't know much about the 300 aac. But if the neck size is similar, they you could give it a try. These dies do not do a full case resize, so if you can get the case to go in all the way to the neck, you could use a dowel or something to push the case past the bottom of the resizing die.
saltyshellback it's very tempting thankyou
I have had Great luck with ALL my LEE reloading equipment.
Just ordered a 9mm version from PSA.
They are a good field reloading kit and good for learning how to reload.
too cool. i can get something like this for my dad's hunting ammo 300 savage & 30-40 krag. do you hunt with the 30-06?
Great video!!
Muchos grasias! 😀
@@saltyshellback I ordered mine should be here Monday for my 308. I'm excited to load a few a shoot them too!!
Do you use the dipper for this? I have a set of dippers and have yet to find a dipper that measures out powder within specs for the powders I use.
I use a powder scale and a dispenser but probably should use a dipper and the scale.
no trimming cases? im in.
Only if you use the reloads in the same rifle.
What does it cost to reload one round vs cost of buying one?
it can very on the quality and per component cost.
Yeah, I kind of wondered about the crimp, but it's in there pretty tight. We'll see when I shoot it if the other bullets move.
I use to use a led sled to sight in and shoot for groups but I learned real quick that was not good for scopes and tight groups.
The sled is too rigid for the fluid motion of recoil . Sand bags are the way to go.
You probably know this already but if not , use sand most definitely. .
If you make another video of the same ammo and reloads at 100 yards , I'd like to see that !
Thanks again , David
David Ray Here is my most recent day at the range. I was shooting my nephew's guns. I didn't change the reticle settings, just compensated for where the crosshairs were aiming in relation to the actual shot placement. That way, I don't mess up his shot placement.
ruclips.net/video/a8Ko3CUPjqw/видео.html
what happens if I have a lot of casings that have indented case mouths? As in, maybe it was deformed during ejection or otherwise? Will this still get them back into shape? Same issue with my .223 casings?
It depends on how badly they are kinked. You should be able to reform most dents with the de-priming punch. Just work the punch into the case mouth slowly if it is a tight fit.
Yeah, I was thinking that might do just fine. I actually just checked out about 25 .223 cases in the pile and I only saw one, maybe two that I may just have to keep on the side or discard. That's really not too bad I suppose. All my .30-06 looked pretty nice though. Thanks a lot for the quick reply. I actually just ordered one for .30-06. Looking forward to using it! :)
Good deal! The Lee Loaders are fine for small quantity reloading and they help new reloaders understand the process. I have a progressive press for my higher quantity calibers like .40 and .45, but I only reload like 10 to 20 30-06 per year, so it is not practical to get something that can crank out hundreds per hour....lol
Beatiful 👍🏼💯💯
Thanks!
Thank you.. very informative. This got me started. My only question is ... I am never over in length but under... are there issues with being under ? We are not talking a lot.
As far as being under, I do not know of any issues as long as the overall length (OAL) of the cartridge is within specifications. Too long and the cartridge will not chamber. Too short and there is a phenomenon called "skipping" that could cause inaccuracy, albeit most of the time negligible unless you are a competitive shooter or something. Usually after a few reloads (could be 2 times, could be 10 times), the case neck will expand due to the explosive pressure, so just keep an eye on the case length. I only have about 2 reload cycles on my 30-06 cases and they are still in good shape. Hope that helps :-)
These are good for working up a new recipe at the range. Once you have things dialed in take it to the press at home.
I have a question. Can you use .308 bullets to reload .30-06, how much powder and what kind of powder should I use?
Thank you.
H.D.Instrumental I am not sure. Sorry. Try handloads dot com. They have a lot of good load data. I usually reduce their load data by at least 10% on my first loads and check to make sure the load is not a squib load after the first shot (check the barrel to make sure the bullet made it out).
@@saltyshellback a .30-06 bullet is .308 in diameter so yes it's the ame thing. Only the shell is a different size.
Rich D OK Thanks. I think I meant that I didn't know what the powder charge would be for a .308. I'm old and I forget things...lol
Did you check head spacing?
nope. I just make sure it does not exceed max OAL. I am not so concerned about bullet skip.
@@saltyshellback online it says these reloaders are not meant for semiautomatics, is that what you shoot from?
Eternal Resolute It's for a bolt action rifle.
I cannot get my bullet to seat. It just pushes it into the case. Following the instructions but not having desirable results
The wall thickness of the neck may be too thin. It has happened on a couple of my reloads.
I need one of these kits for 7MM Mauser (7x57mm). Do they make one for that caliber?
I am not sure. I looked at miswayusa and e-bay but did not find it. You may want to do a youtube search for lee classic loader 7mm mauser to see what other people came up with. Hope that helps.
I need one for 8mm Mauser, but they're rare and very pricey.
I think if you used the primer/ case brush to clean the primer home,it will go in much easier. I use to reload with my Father,all RCBS equip. When he stopped hunting it all got sold, damm I missed out on ALOT of tools.dies ,etc. I may try and buy a couple of these and see what I think. ''Hey how much would ya say it cost ya to make a box of shells ?
At one point did u put a used primer into your reload?
Good job brother. Looks like it works nice.
BENCHREST SHOOTERS RELOAD THE SAME CASE ON THE FIRING LINE,WITH A LEE LOADER!!!!!!
it is sloowwwwwww..but backpack friendly
For sure!
Is it true that by flipping it over you can put a crimp to finish the round?
I have tried, but it depends if you have a bullet with a crimping groove or not. I have not had good luck trying to crimp on a bullet without a crimping groove. You have to be careful not to bend the shoulder of the round when trying to crimp that way. Hope that makes sense.
SaltyShellback what type of Lee Loader are you using EXACTLY? Can you put the link to where you got it in the description or the model number?
Jake DuBois It is from Midway USA. Lee loader classic for 30-06. www.midwayusa.com/product/508946/lee-classic-loader-30-06-springfield
Do you have to resize the brass first for over all length?
edward guillo This kit only resizes the neck. It is not meant for high volume reloading or for use with multiple guns. There is a chance the reloaded rounds won't fit anything besides the last gun it was fired from due to the chamber size.
@@saltyshellback ok thank you
you can always purchase a Lee case trimer. it is used to resize overall length.. you should get one. cheap and efficient. I resize all my brass for over all length.
grant hunter 3 I have a case trimmer, but don't shoot enough 30-06 to need to trim those cases.
no problem.. have you ever had a problem to chamber a 30 06? just curious.. I have found many with my 270win. parent round is the 30 06
Excellent. I have one in .223 No directions just youtube. Great video.
Thanks!
@John Beige Yes they are.
My pleasure. I'm glad it helped :-)
What kind of groups and do you any target pics ?
Thanks !
David Ray They worked better than factory rounds. I made a video.
ruclips.net/video/IqRspiD9XYw/видео.html
saltyshellback
Good vid. No need for lubing case?
Nope. It just resizes the neck. It does not resize the full case, so there is less friction and the cases can be tapped out with the punch.
Yes, lube the case. It will make it easier knocking the case out and priming in the same motion. He doesn't know this so he says "it doesn't work for me" and knocks the case out then primes it.
Something i need to get into ..Cool vid my brother
So the video he mentioned of "Logcabinlooms" using the lee loader was made private or removed, however I did you one betta. Much Mo betta. Here's the inventor of the product showing his technique. Slow is smooth and smooth is fast, and he's pretty damn smooth people. Link's below.
ruclips.net/video/UeEl9wZyabc/видео.html
Cool! I'll check it out! thanks
@@saltyshellback No, thank you. I've been weighing the pros and cons of reloading for just a couple calibers and your video helped me make my decision. I appreciate the time you took to make a video on the products. I'll be picking up a classic loader kit and the powder measure kit this week. Have a great day.
so after the equipment how much does each bullet cost to reload for 30.06
zed zardoz The bullets cost about 17 cents, the powder is about 5 cents and the primer is about 4 cents, so a total of about 26 cents per round to reload.
saltyshellback How are you figuring your powder charge cost? Also, are you buying those bullets by the case or something? Just seems a little low cost-wise. $23/lb powder comes out to $0.16 per 50gr charge, and a lot of quality 30cal projectiles seem to run around $0.25/ea. But, I'm not buying bulk so perhaps that's my problem lol.
I got the supplies in the pre-panic days. I also only use 42 gr of powder :-)
Resize won't go in rifle chamber
Makesure fit in rifle chamber before load in
OK
You need to use the yellow side of the hammer and don't hit as hard you will have much better results. Don't ever take the case out of the die to seat the primer😮😮
OK
Interesting!
It's good for calibers you don't shoot a whole lot.
Are these safe to shoot
Yup. Here is a video of me shooting them. ruclips.net/video/IqRspiD9XYw/видео.html
Great video just got mine in the mail waiting on my scale so i can measure the gun powder
Good deal!
Question: On amazon (as well as some youtube channels) it says that lee loader only resizes the neck and therefore it is suitable only for bolt-action rifles. How safe is it to resize only the neck? I am only concerned with the safety as I have only bolt-actions anyway.
Pirouz Pourdowlat It is not a big deal to just resize the neck. As long as there are no cracks in the casing, there should not be any safety concerns. The only catch is sometimes if you shot the round out of one gun and don't resize the whole case, you may not be able to chamber it in another gun that may have a smaller chamber. Other than that it should work in the same gun.
Been resizing my ammo using this systems for many many years. I only shoot bolt action rifles, so I can not comment on semi autos. Most semi autos would require a crimp. but I never had a problem in my bolts. All rifles produce sub moa or half moa. take the time to inspect all brass for defects before reloading. One thing. some cases such as 270win have a habit of getting larger in diameter,, there fore every time I resize the brass I always check to see if it chambers in my rifle before I proceed to reload primer and powder. otherwise.. no problem. I shoot about 2000 rounds per year.
How many times can the brass casing be reloaded.
+jimmy galloway Basically until you notice cracks, especially on the case mouth.
Thanks very much it's a great video well explained.
My pleasure! Glad it helped :-)