Thank u. Pag disconnected n ung mismong magnetron tube sa filament terminals nachecheck nman na wala na shorted. Medyo mabusisi lang magpalit ng filament terminal pero I think worth it nman than to buy a new magnetron. Make sure lng cguro n maayos ang gawa para wag mag karoon ng arcing. Thanks again for your very helpfull response and videos. Keep safe always, bro.
good video...irritating music.. the best thing about this video is that you showed the difference between good and defective (transformers/capacitors/diodes & magnetrons) thumbs up to your video
Heavy varnish on laminations is a insulator on transformer! Base where it is bolted to chassis would be better to show up shorts between coils and laminations!
Very informative! What should be the normal capacitance for microwave HV diode? I replaced the original HVR-1X 3 with CL04-12 HV diode, now the microwave is heating the food. I set the digital multimeter to 200M, the original HVR-1X 3 reads 7.5 and the new CL04-12 reads 17.
Thanks for this very informative post. I checked all HV components on my Sharp R89ST, to find them ok, but found the HV diode had gone down taking the HV fuse too. The only other thing was the HV capacitor discharge resistor had failed. But this is not a requirement to run.? My microwave now runs in all functions but does not heat the food despite the case above the magnetron getting warm. Any ideas where to look more deeply next. Cheers.
I performed the test on the magnetron and the results would suggest that it is fine. I notice NO crack in the magnets either. I have a Panasonic Prestige 1300W inverter microwave oven. The issue was that it would chip the breaker after 2-3 secs. The switches tested fine. If I disconnect the magnetron from the inverter board microwave does not chip out. Once I connect it the issue occurs again. Any insight?
Sir continuity lng ba ang ginamit mo sa pagtest ng short to Ground ksi ung tester ko Hindi auto range anong range po ang gagamitin ko kng magtetest ako sa winding to body tnx sir
Hi great video - tested my transformer - on hi voltage winding I am getting 82.6 it’s a zebra 100TT in 120V & 60 hz - On other side getting .4 not .5 to 1 1/2 It’s a Viking microwave with oven - Microwave works just no heat up food - the sound is a lot less then before as well - change Magnatron - changed Diode and high voltage capacitor and all switches - do you think it’s the transformer ? With those readings above that’s bad ? Thank you !! Michael
Boss sir magkanu po magpaayos sa inyo ng sony smart tv 42 Inc ? Ok nman po yung sound nya ano lng po yung sa screen nya walang lumalabas😊😊thank you po😊😊
boss ask ko lang, checked na po lahat good ang transformer, good ang capacitor, good ang lahat ng fuse good din po ang magnetron, pero lagi pa din blowing ang main fuse, ano pa po kaya ang reason, baka po may na encounter na kayo na ganitong scenario, tnx
Sir, ok lng b n ung filament terminal n lng ng magnetron ang palitan? Ito nman ang laging nagiging shorted. Madami kasi ako nakikita dito s youtube n palit filament terminal lng at meron nman nabibili nito online para makatipid sana. Thanks
hello sir ,,marhaba...silent subcriber nyo po ako sir...ask ko lng po sana kung normal lng po ba sa capacitor ng microwave na kung itest ko po sya good naman po pumipitik naman po...pero pag sa isang termal then yun isa sa body po nag cap may reading po mga 15ohms...sana po mapansin nyo ako...shukran thank you po sa pag response...
Sir tanong Lang ako nagpalit ako magnetron socket at di na busted ung high voltage fuse Di na grounded pero ,palaging busted ung fuse sa may inlet . .Sir ano Kaya ang issue?
Sa lahat po ng nanonood ng video ni sir sna po wag po natin skip ang ads nya para makatulong tyo s kanya.maraming salamat po godbless
Maraming salamat sir and God bless po...
Agree, tinutulungan tau ni sir pro Tech. Kailangan din natin magsupport sa kanya kahit man lang wag iskip ang ads.
Video is good, but it would have been better if voice and explanation were added side by side.
Thank u. Pag disconnected n ung mismong magnetron tube sa filament terminals nachecheck nman na wala na shorted. Medyo mabusisi lang magpalit ng filament terminal pero I think worth it nman than to buy a new magnetron. Make sure lng cguro n maayos ang gawa para wag mag karoon ng arcing. Thanks again for your very helpfull response and videos. Keep safe always, bro.
Maraming salamat sir s kaalaman kng paano malaman ang sira ng hv transformer at iba pang parts ng microwave
thank sir sa info about sa pag test pyesa na ginagamit sa microwave
Great job, most comprehensive easily understand video
Thanks for sharing ideas boss, baka pede mag test din kayo yung may supply voltage nman sa next video nyo..
good video...irritating music.. the best thing about this video is that you showed the difference between good and defective (transformers/capacitors/diodes & magnetrons) thumbs up to your video
Turn down the volume?
You're the best man who did video tutorial uploaded.. easy to understand thanks Alot my friend☺️may god bless you
Ohne Worte, leicht zu verstehen wie Bauteile einer Mikrowelle geprüft werden können. Klasse!
Good one, you are a professional in this
Thanks a lot 😊
I see a lot of video
Your video is very good
Thank you very much
Good .defective compare is very nice
Nice thanks dito sir more power sa channel mo
Please mention when you test on which range u have set the multimeter and what should be the reading of good and defective what you are checking
Very good testing process 😊
Maraming salamat po sir malaking tulong po ito sa amin.godbless u sir
salamt po kuya . dami ko natutunan
Great video! Thank you! It was very easy to understand.
Very important you check and show analog meter well dane god bless you.
Thank you
Very straight to the point. ❤️
Thank you sir. Your video gave me lots of knowledge.
Very simple to understand
Good Job
Nice video sir thank you ng marami
Excellent ❤❤❤.
Thanks. It was very easy to understand.
Nice tutorial bro thanks for sharing,
Does magnetron has a polarity or if I connect in reverse will it blow up and is there any way to find its polariry
No polarity
@@protechelectronics79 thank you sir
Nice bossing thanks for sharing..
Maraming salamat din bossing.
How to check they with digital multimeter? How to set it? Can you write in description the setting ex Mega Ohm for magnetron ect. Thanks
Hello sir.good day to you.if the value between HV terminal and body shows 75.4 ohms,its good condition or bad.?
Nice tutorial boss idle
Boss baka puede rin mag video kong paano mag palit ng door switct at turnanable switch ng microwave oven salamat
Thank you. Great video.
Ser tnk u po sa learning
Another interesting and sourcefull video. Thank you sir. God bless and be safe.
Salamat sir...God bless
Good job sir god bless you
Thanks so much sir
Heavy varnish on laminations is a insulator on transformer! Base where it is bolted to chassis would be better to show up shorts between coils and laminations!
thanks for getting knowing Godbless..
Thank you for sharing. Very Useful Information. New legit friend . . You got my Red support.
Very informative! What should be the normal capacitance for microwave HV diode? I replaced the original HVR-1X 3 with CL04-12 HV diode, now the microwave is heating the food. I set the digital multimeter to 200M, the original HVR-1X 3 reads 7.5 and the new CL04-12 reads 17.
Does it works?
What is the multimeter settings for transformer.... Can't see in the video.
Ohm
@@protechelectronics79 thanks sir
Magnetron not short out on frame getting continued on coils but not working although all others parts is good what can be the possible cause
Nice practical
Thanks for this very informative post. I checked all HV components on my Sharp R89ST, to find them ok, but found the HV diode had gone down taking the HV fuse too. The only other thing was the HV capacitor discharge resistor had failed. But this is not a requirement to run.? My microwave now runs in all functions but does not heat the food despite the case above the magnetron getting warm. Any ideas where to look more deeply next. Cheers.
Do I have to take the transformer out to perform this?
No need to take it out, just disconnect the wire connections of the transformer and check.
Great video! Thank you!
I think the "symbol" of the diode is inverted,
But the measurement is correct.
I performed the test on the magnetron and the results would suggest that it is fine. I notice NO crack in the magnets either. I have a Panasonic Prestige 1300W inverter microwave oven. The issue was that it would chip the breaker after 2-3 secs. The switches tested fine. If I disconnect the magnetron from the inverter board microwave does not chip out. Once I connect it the issue occurs again. Any insight?
Try to change new magnetron.
Thanks for sharing sir
Good job bro
PLEASE WRITE ANSWER..I WANT ASK THAT BECAUSE CHECK TEST THE PRIMARY WINDING FROM TRSNSF.MICROWAVE IS 2.8 OHMS. ITS GOOD OR NOT? THANKS FOR ANSWER
salamat boss...pwdi magtanong? saan pwdi makabili ng ganyang mga pisa?..wala kasi dto sa cebu..yung legit na online site..
No idea boss kung saan pwede omorder online.
Sir continuity lng ba ang ginamit mo sa pagtest ng short to Ground ksi ung tester ko Hindi auto range anong range po ang gagamitin ko kng magtetest ako sa winding to body tnx sir
Yes sir continuity lang
If mark value of capacitor is one microfarad and measured value by a DMM is .87 microfarad. Then capacitor is ok or not. Waiting for your kind reply
Ed Aranaz ask q lng sir hinde b pwede Ang multi tester pang test sa high voltage trasformer at anng pwede pang test sa RK
Pwede nman sir gamitin ang multitester, nakasanayan ko lang kasi gamitin ang digital at makukuha mo ang saktong reading.
@@protechelectronics79 tnx po sir God bless
Thank you sir.
What is the black measurement device replacement of the digital multimeter???
Analog meter.
168.9 ohm line to ground is good? Should it be 0 right?
Typical Readings on a Microwave transformer: Filament winding:
Nice content sir keep posting god bless
Salamat po God bless..
i like your video
nice video boss
nice video
Hi great video - tested my transformer -
on hi voltage winding I am getting 82.6 it’s a zebra 100TT in 120V & 60 hz -
On other side getting .4 not .5 to 1 1/2
It’s a Viking microwave with oven -
Microwave works just no heat up food - the sound is a lot less then before as well - change Magnatron - changed Diode and high voltage capacitor and all switches - do you think it’s the transformer ? With those readings above that’s bad ? Thank you !! Michael
Can we use any side for diode
Reduce boring odio , good
Sir tanong ko lng po Yung nabili ko mot ang reading sa tester ko po sa hv output nya ay 208ohm,good po ba ito? Salamat po sa sagot😊
Sir kapag OL or open yung last test mo sa hv xformer may prob? dapat ba at least nasa hundred ohms yun?
Yes po
Useful sharing
hi po, ask ko lang po, pag digital po ginamit q pang test sa diode wla po sya reading pero pag analog meron po ano po kaya problem?
Sa digital wala po talagang reading pero sa analog may mareading pero sa high resistance.
thx now i know the bad ones
Salamat boss
Boss sir magkanu po magpaayos sa inyo ng sony smart tv 42 Inc ? Ok nman po yung sound nya ano lng po yung sa screen nya walang lumalabas😊😊thank you po😊😊
boss ask ko lang, checked na po lahat good ang transformer, good ang capacitor, good ang lahat ng fuse good din po ang magnetron, pero lagi pa din blowing ang main fuse, ano pa po kaya ang reason, baka po may na encounter na kayo na ganitong scenario, tnx
Check po yong mga door switch, may upload video na po ako tungkol sa ganyang problema check nyo na din po.
What kind of tester is the second one used in the video?
It's an analogue tester.
@@chrisophertshabalala TYVM!
@@Brian-yz8dj KYVM. It's an abbreviations let me know its meaning please, also the first one is...!? 🤔
@@chrisophertshabalala TYVM = Thank you very much.
Transformer Magnetron HV capacitor ka price kya kya hai thank you
Sir, ok lng b n ung filament terminal n lng ng magnetron ang palitan? Ito nman ang laging nagiging shorted. Madami kasi ako nakikita dito s youtube n palit filament terminal lng at meron nman nabibili nito online para makatipid sana. Thanks
Pwede nman sir bastat sigurado lang na mawawala ang shorted.
Nice sir
Thanks sir...
Multimeter knobs position...?
hello sir ,,marhaba...silent subcriber nyo po ako sir...ask ko lng po sana kung normal lng po ba sa capacitor ng microwave na kung itest ko po sya good naman po pumipitik naman po...pero pag sa isang termal then yun isa sa body po nag cap may reading po mga 15ohms...sana po mapansin nyo ako...shukran thank you po sa pag response...
Wala po dapat continuity ang terminal to body ng capacitor.
IBIG SABIHIN PO BA HINDI KAYANG MADETECT NG ANALOG TESTER YONG SIRA KAYA HINDI MO PO GINAMITAN NG ANALOG TESTER?
Kaya nman po, digital lang ang ginamit ko para makita ang saktong reading ng resistance bawat winding.
Nice
Saan kayu middle east boss
Saudi boss
Master tanong ko Lang po ano pinang di diischarge nyo sa high voltage cap?
Short to ground lang po...
Sir pwede bang ipalit ang 0.75 sa 0.85 capacitor ng microwave
Yes pwede po.
Thanks a lot
sir saan makakaorder ng mga parts nito hv cap, mgntron hv diode,
Check nyo po marami po yan online or sa Raon don po ang bilihan.
thanks paps
Sir ano po yon Value ng diode salamat po
CL04-12, 450mA 12kV High Voltage diode.
thankas
Sir umuusok po ung transformer ng microwave ko sira na kaya un saka ung diode nya sir kapag tinester ko ng baliktaran may reading
Sira na yon sir kung umusok, shorted na din ang diode kung kabilaan may reading.
Thanks
Sir tanong Lang ako nagpalit ako magnetron socket at di na busted ung high voltage fuse
Di na grounded pero ,palaging busted ung fuse sa may inlet . .Sir ano Kaya ang issue?
Check po door switch
Merona inaayos microwave midea problem pumuto or nag spark magnerton pinalitan ko ma magnetron at Capacitor
Ganon parin
Mantep gan
good
Di mupo naipakita sa analog tester yong sa transformer po
आरे भावा मुजीक देवुन काय डी जे वर नाचायच आहे का ❓
I don't understand why you tubers are adding background music.