can this be used to operate 3 servos but in stages? example: servo1-starts at 0* goes to 90* servo1-holds 90* for 3 secs servo2-goes to 180* holds for 5 sec servo1- returns to 0* servo2- returns to 0* I have tried everything and no luck. when i execute the program all servos move at the same time.
Muy buena tarde, esta tarjeta puede manejar los 16 servos con la configuración que aparece en el video, es decir no se debe agregar ningún componente adicional? Mil gracias por su respuesta.
Thanks for your comment and idea. The main topic of the video is "Servo motor control", and if what you need is the solution for the "Servo Jitter Problem", the circuit built in this video provides that solution. When it comes to sponsors, almost every creator uses and references some of the opportunities that sponsors provide. 😇
@@maker101io Yes. But there is no proper explanation on servo jitter part. Just connecting capacitors. But why and how does that solve the problem? This is what subscribers ask for. Not HOW to order PCB from china.
Get the multiple servos to go into different directions and under different timing. Get some to hold positions while other servos move and under a group of arrays and state machine Millis. Instead, of just using a delay and they move at the same direction, and timing. The hard part is the previous. How many amps did you use to operate the servos?
A lot of people did not notice, this persons very poor soldering and component prepping skills, the leads are not bent correctly, etc. Components are not fully flush to the board etc. Do I need to go on, I think I'll order a board, and intentionally show how to load and solder this board correctly 3 different ways. And yes I have worked in an electronics repair shop, where you had to know how to prepare and solder components correctly.
📌 www.instructables.com/One-and-Multiple-Servo-Motor-Control-With-ESP32-De/
📌 www.pcbway.com/project/shareproject/Multiple_Servo_Motor_Controller_Board_DOIT_ESP32_DEVKIT_V1_c9c8165e.html
Why you add 330 resister between servo signal and esp32 pin?
i knink voltage division
can this be used to operate 3 servos but in stages?
example:
servo1-starts at 0* goes to 90*
servo1-holds 90* for 3 secs
servo2-goes to 180* holds for 5 sec
servo1- returns to 0*
servo2- returns to 0*
I have tried everything and no luck. when i execute the program all servos move at the same time.
Great video
Thanks 😇
is the jittering handled by a smooth func ? or am I missing something ?
Conclusion: no schematic, no say the why of resistor, and angled cam not help, it's soo bad choices on technical video
Every time excellent project Congratulation 🎉l🎉💯👍
Thanks 😇
Nice info, thanks for sharing it:)
What servo you use?
is this mert arduino?
Yes 😇
L293d video please 🥺
What kind of project are you trying to make with the L293D?
L293d not working 😭😭😭😭😭😭😭😭😭😭😭😭
💛💛💛
Thanks 😇
Muy buena tarde, esta tarjeta puede manejar los 16 servos con la configuración que aparece en el video, es decir no se debe agregar ningún componente adicional? Mil gracias por su respuesta.
No link to Gerber files
www.pcbway.com/project/shareproject/ESP32_Servo_Motor_Controller_Board_Up_to_16_Servo_Motors_277e221b.html
Firts😊🎉
Farts💩🥳
The main motive of the video seems to promote the the sponcerer.
Thanks for your comment and idea. The main topic of the video is "Servo motor control", and if what you need is the solution for the "Servo Jitter Problem", the circuit built in this video provides that solution. When it comes to sponsors, almost every creator uses and references some of the opportunities that sponsors provide. 😇
@@maker101io Yes. But there is no proper explanation on servo jitter part. Just connecting capacitors. But why and how does that solve the problem? This is what subscribers ask for. Not HOW to order PCB from china.
@@madhukeshnp www.instructables.com/One-and-Multiple-Servo-Motor-Control-With-ESP32-De/
Which esp32 are you using because my esp32 does not fit into to breadboard ?
None of the esp32 dev modules fit on to the breadboard.
DOIT ESP32 DEVKIT V1
www.robolinkmarket.com/esp32-wroom-wifi-ve-bluetooth-modulu
اول first I am arab
Get the multiple servos to go into different directions and under different timing. Get some to hold positions while other servos move and under a group of arrays and state machine Millis. Instead, of just using a delay and they move at the same direction, and timing. The hard part is the previous. How many amps did you use to operate the servos?
A lot of people did not notice, this persons very poor soldering and component prepping skills, the leads are not bent correctly, etc. Components are not fully flush to the board etc. Do I need to go on, I think I'll order a board, and intentionally show how to load and solder this board correctly 3 different ways. And yes I have worked in an electronics repair shop, where you had to know how to prepare and solder components correctly.