16:37 I was always taught to push the fishtape by itself to it's destination, then tie a string to it, pull the string back through the ceiling/wall and then use the string/muletape to pull the wire. It seems the way you did it makes it extra hard, as you are not only having to fight the fishtape going all wonky, but also the wire. Double weight, double friction, harder to steer, double hassle all the way around.
As someone who comes from a country where any electrical work needs to be performed by a licenced electrician, it was good to see you coming up with some good solutions for the problems you came across. Fans going backwards though 😂
Wow! I watched this video as eagerly as a TV show. The job you did is a little above my expertise, but it’s still good in watching your thinking process in solving the road blocks in installation. The lights came out beautifully and opened the the room up. I saw the head tilt when you said “make your own video”. The internet trolls are real. Anyway, thanks for sharing.
I installed ceiling fan into my daughter's room. Uninstalled the annoying LED saucer light had the forethought to buy some 12g electrical wire and wire nuts but forgot to buy a junction box. In any case measured center of room and found out that the spot that was needed was right on a joist so mounting fan was easy as pie and just had to run about 3ft of wire to the new spot.
This video was super helpful as I am looking to do something similar and dont have access via the attic. Only difference is I have zero ceiling fixtures to piggyback off of.
good job ! Armchair quarterback comment , if you change the 2 wire to a 3 wire so the fan always has a hot feed , you will eliminate the fan going thru the START/LEARN cycle. It does this do to the power/light switch shutting off power to light/fan total. Also on the new 3 way switch you added , correct the BLACK connection ! seize down screw/wire is on wrong side and not turned clockwise. Looks nice with the finished project !
That’s why is a good idea to use good practice when doing electrical wiring like roughing new construction because I would have pulled a 14/3 to the light for future use or for the tan install, so now you got to do all that work and cutting the walls.
I know a lot of people are teaching people to start the hole drilling without teeth. However I find it easier and faster to use the teeth , but the tip is to start the drill going before you make contact with the drywall. In addition I used the same exact catch bowel and it’s a bad design. Once you get drywall dust in there it clouds up the bowl making it much harder to see where you are trying to cut.
Another step that minimizes hole saw binding is to NOT put even pressure on it when first contacting the drywall/working surface - as in slightly tilting your drill so that your hole saw has pressure in one spot/section of teeth at first and then gradually bring more of the teeth into contact with where you're cutting.
that was an awesome job thank you I also install for lights and Each corner with a fan in the middle and you made it possible by showing me how to do it thank you very much great job
You didn't have to run the wire and tape through both holes from the bathroom, you only needed about five feet to go down the wall to the switch, you could have just pulled that 5 foot down after pushing the wire through only one hole. There are also dual switches that can be put in lace of a single switch, so you wouldn't have to add a 3 gang box on the wall.
Any chance you have the link to other other lights you ended up going with? I am in the same boat, want to have some uniformity with other lights that were installed. Thanks!
Those clips you mentioned that go on the ceiling fan box are called plastic bushing, and the orange connectors on the lights are called Wago push in nuts.
Good catch on that line. This is a prime example of why blind drilling is an absolute no no. It's scary seeing the amount of youtube videos where DIYers drill through joists blindly like it's nothing. Also a good call on ditching the wafer lights. I have the exact recessed lights you went with in the four inch model in my home. When I tried one wafer light I immediately knew I wouldn't be able to stand their look with the glare they give because they're truely not recessed.
Here's a little-known hack. Sometimes you can wire the LED recessed lights into lighting wire of the ceiling fan controller output. The fan remote could then be used as your dimmer. This would eliminate the need for new switching. End result wouldn't have been as nice as having new switching, but it saves a whole lot of work.
@@malawigold747 The hole in the floor joist (for the floor above me so in this case, the ceiling) ? Those come per-fabricated with holes you can pop out.
@@malawigold747 The hole going up through the top plate? Horizontal 2x4s stacked into of each other? The hole and a wire was already there. Your situation might be different.
Nice video and I watched it fully like movie! Do you have video of how you patched the drywall you cut in the bathroom and fixed the minor damage in drywall near the 3 gang switch? I'm more scared on the drywall things, as it is hard to finish like before you know :)
I did not include that part of the project. I was scared too and the fear of the path work delayed this project for a while. It really was not bad at all to do. To repair the hole in the bathroom, I got a piece of drywall from Lowes and cut a replacement piece to size. Then I used this to fill the cracks and sand it down smooth: amzn.to/3Ge5aS4 For the damage around the gang box and filled it in with the drywall putty, sanded, and painted. You really cannot tell there was ever any damage. Just takes some time to build up the putty and let it dry and sand. Fortunately for me I had paint from the builders and knew it was already going to be the right color.
@@ashwinsvideo You're most welcome. If you have not already, please consider subscribing. It would really help me out. ruclips.net/user/DIY-BRY Best of luck on your DIY!
Thats a hell of a job man. hope someone appreciated it enough to cook u a good meal , back rub, while feeding u grapes and fanning u with a big feather. Cuz thats work! Too many jack off corporate professional E-mailers and powerpoint slide creators in the world now-a-days. Not enough "real world" skills left out here.
Cudos brother. This is a decent sized job that many wouldn't attempt without any electrical wiring/maintenance background. Try to leave a flag in your tape so it's easier to remove. Fiberglass pull rods are a good investment, lightweight, most glow in the dark and coke with attachments like hooks, magnetic ect. They go hand and hand with a fish tape. Same thing goes for pull string. Only critique is your fan is rotating the wrong direction.
@@shawnphillips1220 Because I have the fan so close to the ceiling, it forces the air up and out around the room. I have thought about putting in the 3” drop rod and reversing the spin direction, but I think I accidentally threw it out when picking up the garage.
Thoroughly enjoyed the whole video. Nicely done…although I might need to see the follow up video where the dimmer switch “sets the mood”. May need to take notes!! 👍🏼
Why didn't you just connect the new wires to the old wire that was disconnected from the fan? You could have used that original wire and just extended from it and used the original wall switches!!
@@DIYBRY i have a bedroom, the length is 4,88 m and the width is 3,61 m, how many spotlight do I need and how to arrange them ? Some people suggest me to put 12 spots and others tell me 6 or 8 are enough.
@@hocineted7594 The room shown in the video is a comperable size (slightly larger) and I am only using 6 lights, which really is plenty for the space. Especially when the lights are set to 5,000k for the color setting.
Also if you see that the wire feeds threw the joists then you know is not gonna be stable 100% all the time, the holes count as a strapping means , as of if it was ran parallel to the joists then yes it would have to be staple to the joists.
You know you could just have gotten power for the fan from one of those switches right? With out installing that other “fan switch” unnecessary extra work, especially if you have a fancy one with a remote, the remote is all you need as the main means…. Good video though, I enjoyed watching.
Why did you not change the light switches? I recommend to install TP-Link Kasa switch HS200($15) or dimmer HS220($19), and buy Alexa($35) to control them.
First of all, just hire a professional like me, we would never cut up walls just to see were the wire goes, we use a wire tracer , I’m going to comment as the video goes.
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
Added Chapters to this video:
00:00 - Intro
00:42 - Plan Overview
03:22 - Opening Up Drywall to Run New Wires
07:15 - Project Products and Tools
08:52 - Disassemble Electrical Box and Label Wires
12:48 - Planning Wiring
16:06 - Running Wires Though Ceiling (Part 1)
23:46 - Cut Can/Pot Light Holes in Ceiling
32:43 - 6' Joist Drill Bit
34:39 - Running Wires Through Ceiling (Part 2)
38:10 - Ceiling Fan Mount Install
44:22 - Can/Pot Light Wiring
49:02 - 3-Gang Electrical Box Install/Wiring
50:48 - Dimming Switch and Final Testing
53:17 - Final Results
54:50 - Outro
16:37 I was always taught to push the fishtape by itself to it's destination, then tie a string to it, pull the string back through the ceiling/wall and then use the string/muletape to pull the wire. It seems the way you did it makes it extra hard, as you are not only having to fight the fishtape going all wonky, but also the wire. Double weight, double friction, harder to steer, double hassle all the way around.
Thanks for the info in your comment. I think its a matter of personal preference. Were I to do this again I think I would do it the way you explain.
As a journeymen electrician I can say you did a few things a little different than I would’ve but you did a very good job!
You must be a terrible journeyman
@@bradmcmurray4038 I guess I’ll go cry man🥲
What would you do differently?
@@reggieoverton121 I would use a Milwaukee Hole Dozer
@@bradmcmurray4038 his been nice by saying that I'm jw as well n I would of done it different cus I know was up
As someone who comes from a country where any electrical work needs to be performed by a licenced electrician, it was good to see you coming up with some good solutions for the problems you came across. Fans going backwards though 😂
Amerriicaaaaa.... Hahaha I live in the US now from Australia and the amount of DIY you can do without it being frowned upon is crazy
What country did you come from?
Wow! I watched this video as eagerly as a TV show. The job you did is a little above my expertise, but it’s still good in watching your thinking process in solving the road blocks in installation. The lights came out beautifully and opened the the room up. I saw the head tilt when you said “make your own video”. The internet trolls are real. Anyway, thanks for sharing.
I installed ceiling fan into my daughter's room. Uninstalled the annoying LED saucer light had the forethought to buy some 12g electrical wire and wire nuts but forgot to buy a junction box. In any case measured center of room and found out that the spot that was needed was right on a joist so mounting fan was easy as pie and just had to run about 3ft of wire to the new spot.
This video was super helpful as I am looking to do something similar and dont have access via the attic. Only difference is I have zero ceiling fixtures to piggyback off of.
You’ll just have to run new lines. I do show that really long drill bit, which should help you out.
good job ! Armchair quarterback comment , if you change the 2 wire to a 3 wire so the fan always has a hot feed , you will eliminate the fan going thru the START/LEARN cycle. It does this do to the power/light switch shutting off power to light/fan total. Also on the new 3 way switch you added , correct the BLACK connection ! seize down screw/wire is on wrong side and not turned clockwise. Looks nice with the finished project !
good tip on making hole over existing hole - there are other more complicated methods but yours seems to work
Thanks. It turned out splendidly!
Nice video. Just one thing, Raco makes a ceiling fan mount for your joists. No need to glue wood to your joists to make the fan mount bracket work.
Thanks for the info for the community.
Thanks for the video, I really enjoyed and learnt something new for myself.
That’s why is a good idea to use good practice when doing electrical wiring like roughing new construction because I would have pulled a 14/3 to the light for future use or for the tan install, so now you got to do all that work and cutting the walls.
Thanks for the information for the community!
I know a lot of people are teaching people to start the hole drilling without teeth. However I find it easier and faster to use the teeth , but the tip is to start the drill going before you make contact with the drywall. In addition I used the same exact catch bowel and it’s a bad design. Once you get drywall dust in there it clouds up the bowl making it much harder to see where you are trying to cut.
I agree about the bowl, but sure does help to not make a drywall dust mess.
Another step that minimizes hole saw binding is to NOT put even pressure on it when first contacting the drywall/working surface - as in slightly tilting your drill so that your hole saw has pressure in one spot/section of teeth at first and then gradually bring more of the teeth into contact with where you're cutting.
that was an awesome job thank you I also install for lights and Each corner with a fan in the middle and you made it possible by showing me how to do it thank you very much great job
I appreciate the compliment, Arturo! Glad I could help. Thanks for watching! Don’t forget to subscribe😁
Very nice step by step instructions 👏
Thank you! Thanks for watching
Very good video. I followed everything you did. Great job.
Thanks for watching! Consider supporting the channel with a super thanks on the video.
Wago wire connectors. I use and love them for home DIY.
I wish they were a bit less expensive.
Thanks for this video. Great job
Thanks for watching! Subscribe for more! 😎
And I found what I needed (and expected) here about 33:00. Thanks!
Thanks for watching!
"Setting the mood.....Oh yeah!" - love it.....good video
You didn't have to run the wire and tape through both holes from the bathroom, you only needed about five feet to go down the wall to the switch, you could have just pulled that 5 foot down after pushing the wire through only one hole.
There are also dual switches that can be put in lace of a single switch, so you wouldn't have to add a 3 gang box on the wall.
Yeah I was going to say couldn't you just put in a double switch instead of putting in another switch . It'll be less work.
I wanted a separate switch for the fan to match other rooms in the house.
Good job man. What a process!
Appreciate it. How far is the led from the end of fan blades. To prevent strobing?
End of fan blade to the can lights? They do not overlap and I have never seen any strobing.
@@DIYBRY Ok thanks. Just wanted to know the distance.
@@waynegomillion4976 27 inches
@@DIYBRY Ok appreciate it.
Any chance you have the link to other other lights you ended up going with? I am in the same boat, want to have some uniformity with other lights that were installed. Thanks!
www.homedepot.com/p/Halo-LT6-Series-6-in-Selectable-CCT-3000K-5000K-Canless-Integrated-LED-White-Recessed-Light-Trim-Direct-Mount-Dimmable-LT6089FS351EWHDMR/316522126
Those clips you mentioned that go on the ceiling fan box are called plastic bushing, and the orange connectors on the lights are called Wago push in nuts.
Thanks for the information for the community!
Good catch on that line. This is a prime example of why blind drilling is an absolute no no. It's scary seeing the amount of youtube videos where DIYers drill through joists blindly like it's nothing. Also a good call on ditching the wafer lights. I have the exact recessed lights you went with in the four inch model in my home. When I tried one wafer light I immediately knew I wouldn't be able to stand their look with the glare they give because they're truely not recessed.
Thanks for watching!
Here's a little-known hack. Sometimes you can wire the LED recessed lights into lighting wire of the ceiling fan controller output. The fan remote could then be used as your dimmer. This would eliminate the need for new switching. End result wouldn't have been as nice as having new switching, but it saves a whole lot of work.
Cool suggestion. Though I do very much like having the fan on its own switch. Also think it is a better setup for resale purposes.
That was dope, I tried to install these lights but my wiring wasnt compatible with the ceiling light I purchased
Did you find an alternative?
So the hole was already there? In the plate
?
@@DIYBRY the hole that u fed the wire up thru to go in the ceiling, the hole in the wood, behind the peice of wall u cut out.
@@malawigold747 The hole in the floor joist (for the floor above me so in this case, the ceiling) ? Those come per-fabricated with holes you can pop out.
@@malawigold747 The hole going up through the top plate? Horizontal 2x4s stacked into of each other? The hole and a wire was already there. Your situation might be different.
@DIY•BRY yes that's what I was referring to, didn't see you drill it. Thx!
Nice video and I watched it fully like movie! Do you have video of how you patched the drywall you cut in the bathroom and fixed the minor damage in drywall near the 3 gang switch? I'm more scared on the drywall things, as it is hard to finish like before you know :)
I did not include that part of the project. I was scared too and the fear of the path work delayed this project for a while. It really was not bad at all to do. To repair the hole in the bathroom, I got a piece of drywall from Lowes and cut a replacement piece to size. Then I used this to fill the cracks and sand it down smooth: amzn.to/3Ge5aS4 For the damage around the gang box and filled it in with the drywall putty, sanded, and painted. You really cannot tell there was ever any damage. Just takes some time to build up the putty and let it dry and sand. Fortunately for me I had paint from the builders and knew it was already going to be the right color.
@@DIYBRY Thank you for the detailed tip. Really helps.
@@ashwinsvideo You're most welcome. If you have not already, please consider subscribing. It would really help me out. ruclips.net/user/DIY-BRY Best of luck on your DIY!
I didn't see where you got the power or 120v for the fan as the original setup only had two switches two 120v wires.
It is all in the wiring. The same power source that is providing power to the other switches.
Thats a hell of a job man. hope someone appreciated it enough to cook u a good meal , back rub, while feeding u grapes and fanning u with a big feather. Cuz thats work! Too many jack off corporate professional E-mailers and powerpoint slide creators in the world now-a-days. Not enough "real world" skills left out here.
😎
I'm glad you didn't use that puck light .. the baffled style looks so much better.
Thanks and I liked the details
Tubular. Please consider subscribing: ruclips.net/user/DIY-BRY
I dunno about the screw driver,... but I always carry around a "Nice, Big and Long one" ;)
That’s what she said!
Cudos brother. This is a decent sized job that many wouldn't attempt without any electrical wiring/maintenance background. Try to leave a flag in your tape so it's easier to remove. Fiberglass pull rods are a good investment, lightweight, most glow in the dark and coke with attachments like hooks, magnetic ect. They go hand and hand with a fish tape. Same thing goes for pull string. Only critique is your fan is rotating the wrong direction.
I have the fan going that way intentionally. Better all over airflow for the space. Can easily be changed with the press of a button on the remote.
@@DIYBRY interesting, I thought it wouldn't have created very much air like that but if it works, it works!
@@shawnphillips1220 Because I have the fan so close to the ceiling, it forces the air up and out around the room. I have thought about putting in the 3” drop rod and reversing the spin direction, but I think I accidentally threw it out when picking up the garage.
Thoroughly enjoyed the whole video. Nicely done…although I might need to see the follow up video where the dimmer switch “sets the mood”. May need to take notes!! 👍🏼
Good enough to earn me a new subscriber? :)
great video, thanks!
Thanks for watching!
Good job.
Why didn't you just connect the new wires to the old wire that was disconnected from the fan? You could have used that original wire and just extended from it and used the original wall switches!!
Which is basically the end result of what I did.
That’s what she said 😂😂😂
👍👍👍
That.s what she said…lol!
your ground wires in switch box should be twisted together.
Thanks for the info for the community.
Can you help to arrange downlighting in my bedroom ? I will send the plan you on wattsapp
I do not use WhatsApp
@@DIYBRY how do we communicate ?
@@DIYBRY i have a bedroom, the length is 4,88 m and the width is 3,61 m, how many spotlight do I need and how to arrange them ? Some people suggest me to put 12 spots and others tell me 6 or 8 are enough.
@@hocineted7594 The room shown in the video is a comperable size (slightly larger) and I am only using 6 lights, which really is plenty for the space. Especially when the lights are set to 5,000k for the color setting.
@@DIYBRY i am using spotlight of 5 watt that produce 500 lumens and the temperature is 2700 kelvin, so 6 or 8 are enough ?
Take the fans down and you can see where the joists are. Just pull what you need from box through to hole. Waste of time to measure runs like that.
Thanks for the information for the community!
Great Job👍🏽My Question To You Is Why There Isn’t No Insulation On Your Ceiling And Is Snowing Outside 🤓 APRILFOOLSNOW
No more explain, just do it! viewers can understand.
As I always say…if you didn’t like my video, feel free to make your own video!
Good vid.just too much talking
Noted
Too much talking for just litlle job
RIGHT?
Like I say, feel free to go make your own video 😎
Also if you see that the wire feeds threw the joists then you know is not gonna be stable 100% all the time, the holes count as a strapping means , as of if it was ran parallel to the joists then yes it would have to be staple to the joists.
Thanks for the information for the community!
You know you could just have gotten power for the fan from one of those switches right? With out installing that other “fan switch” unnecessary extra work, especially if you have a fancy one with a remote, the remote is all you need as the main means…. Good video though, I enjoyed watching.
Thanks for watching!
Why did you not change the light switches? I recommend to install TP-Link Kasa switch HS200($15) or dimmer HS220($19), and buy Alexa($35) to control them.
Thanks for the info for the community.
First of all, just hire a professional like me, we would never cut up walls just to see were the wire goes, we use a wire tracer , I’m going to comment as the video goes.
Thanks for the information for the community!