Will look even cooler if you relocate the front blinkers on your forks.. Right on the left and right side of the headlight. Then you will have a nice clean handlebar look.
Man, That new Speed/Tach is Dope! ( i never use the word dope ever so feel awesome ;) It really looks great. :) -I am trying to figure out the weirdness that is removing the rear sissy bar brackets on my 95 Dyna Low rider. (just got it.. been wanting this model for wayyyyyyyyyyyyy long time..) Somehow tho, removing both the saddle bag brackets and the afore mentioned bits are proving quite "WTF" lmao... If I were new to working on bikes, ok sure,. but after building and repairing near 50 of them by myself, I'm pretty much a ball of shame for not being able to figure out what kind of voodoo they used to make this process This much of a "WTF". Anyway, great vid. Cheers!
hi , just wanted to ask you about the rear turn signal relocation kit you have fitted, as i can't get any info on youtube. was there any cutting or soldering involved or just remove the indicator and rethread the wires back, any info would be awesome, cheers
Yes, if I remember right, there was a little soldering because I had to cut wires to get them back out through the old turn signal bracket tubes. The connectors were too large to fit.
I used a "run brake turn controller". It is a little device that plugs into the wiring harness. I put that in and replaced the rear turn signal lenses with red ones. It is way easier than completely rewiring the rear end.
Here are the links to the tail light and front/rear LED replacement lenses. www.revzilla.com/motorcycle/kuryakyn-led-taillight-conversion-kit-for-harley-1988-2017 www.revzilla.com/motorcycle/kuryakyn-led-rear-bullet-turn-signal-conversion-kit-for-harley-2000-2018 www.revzilla.com/motorcycle/kuryakyn-led-front-bullet-turn-signal-conversion-kit-for-harley-2000-2018
It was pretty easy! The one I used is available straight from Harley. Unfortunately I was done with the install before I remembered that I didn’t shoot any video.
Great upgrades where did you get the wrap aroud license plate holder?
Will look even cooler if you relocate the front blinkers on your forks.. Right on the left and right side of the headlight. Then you will have a nice clean handlebar look.
Good Video, I bought the same speedometer but can get it to sync up through the cable. Did you have to do anything special. Mine is a 2009 SG custom.
Hey did you upgrade your speedo/tach somwhere along the line? Thinking of doing mine the same so I'm able to see the RPMs
Looks great. I have the identical bike. Seemed strange watching ya work on it. lol
I didn't see you test your brake light.
TheBigpappa160 Oops! I must have cut that out in editing! Rest assured, I tested it all before riding and always retest regularly!
Man, That new Speed/Tach is Dope! ( i never use the word dope ever so feel awesome ;) It really looks great. :) -I am trying to figure out the weirdness that is removing the rear sissy bar brackets on my 95 Dyna Low rider. (just got it.. been wanting this model for wayyyyyyyyyyyyy long time..) Somehow tho, removing both the saddle bag brackets and the afore mentioned bits are proving quite "WTF" lmao... If I were new to working on bikes, ok sure,. but after building and repairing near 50 of them by myself, I'm pretty much a ball of shame for not being able to figure out what kind of voodoo they used to make this process This much of a "WTF". Anyway, great vid. Cheers!
Dang. I don't think I can fit anymore under my seat between alarm and USB.
hi , just wanted to ask you about the rear turn signal relocation kit you have fitted, as i can't get any info on youtube. was there any cutting or soldering involved or just remove the indicator and rethread the wires back, any info would be awesome, cheers
Yes, if I remember right, there was a little soldering because I had to cut wires to get them back out through the old turn signal bracket tubes. The connectors were too large to fit.
Can you still use the new speedo/tach combo to read codes?? I would think you can but I hate to assume
It's a Harley part, so I would imagine you could. I've never tried or looked into it.
how did you get your signal lights to work also as running lights
I used a "run brake turn controller". It is a little device that plugs into the wiring harness. I put that in and replaced the rear turn signal lenses with red ones. It is way easier than completely rewiring the rear end.
I can’t find these for my 2010 fxdwg. Can you post the link?
Here are the links to the tail light and front/rear LED replacement lenses.
www.revzilla.com/motorcycle/kuryakyn-led-taillight-conversion-kit-for-harley-1988-2017
www.revzilla.com/motorcycle/kuryakyn-led-rear-bullet-turn-signal-conversion-kit-for-harley-2000-2018
www.revzilla.com/motorcycle/kuryakyn-led-front-bullet-turn-signal-conversion-kit-for-harley-2000-2018
How did you upgrade the speedo ??
It was pretty easy! The one I used is available straight from Harley. Unfortunately I was done with the install before I remembered that I didn’t shoot any video.
Excelent....