Tesla Model Y Light Bar Starlink Wide-Strip Taillights! MUST HAVE Accessory by Hansshow
HTML-код
- Опубликовано: 5 сен 2024
- #tesla #modely #model3 #cybertruck #starlink
🔥Link to Light Bar: www.hautopart....
👉 Discount code to use at checkout: MEGAWATTS
🔥🔥ORDER A TESLA MODEL FOR UP 2,500 credit using this link! It will help keep this channel going! 👉👉👉www.tesla.com/...
![Hansshow Full-Width Strip Rear Tail Lights [Installation & Review]](http://i.ytimg.com/vi/cnfqDRcb0yY/mqdefault.jpg)
Trying to install this right now on a Model 3 and this video leaves a bunch of stuff out as to what plugs into what. The written instructions are not much better. I knew this thing was going to be a pain in the ass.
It's so super simple. It's literally unplug the OEM lights and plug these in. It could not get any simpler.
You should probably have one of the neighborhood kids install it for you.
Finally a lightbar that looks OEM and not cheesy.
This changes the vertical position of the rear camera. Tesla cameras are precision mounted, so now the rear camera is out of calibration.
Shut up nerd.
Did u find a way to fix it ?
Did you have any partial blocking of the backup camera view after instal of this lightbar?
Did you try this?
is your back up camera image whack after installation?
Can you notice any red light in the reverse camera?
Would that it would serve as a Starlink antenna and receiver. I'm waiting for something like that, to replace the Sirius/XM radio that we can't get on the Model Y.
Not this version has no association with starlink and it has no correlation - just how it’s being branded
Can it work without the startup sequence?
Ok. To turn off the signal feature on the knight rider full width strip, how do i do that?
Looks great. Much easier than the other light bar
What is the orange pyramid light at the bottom of your rear bumper?
I have ordered a lot of Tesla stuff from Hanshow they don’t send tools with to install it I have asked them several times
But don’t sent it even I just bought ambient lights kit for my Tesla model y the only thing they sent out with ambient lights kit is gloves
I'm guessing there's no way to configure the way the lights work. I would really prefer if the whole light bar didn't flash with the blinker
Guy can cut the indicator wires
@@megawattsooo so its possible to have this exact setup but without the indicators? I personally think its just too much with the indicators
@@racksontheway659I agree style wise but wouldn’t it be safer? No such thing as too much attention when it comes to indicators
I don't like it to be triggered when indicators are on, is there a way to program it?
I notice you installed the pilot light at the bottom. How does the wire connection from that light to the tail lights, then to your new light bar strip link tail light?
Trying to install this on a 2023 Model Y Performance. The light strip is 3 inches on the in the center (widest point).
The to be installed (above plate) is 2 1/2 inches deep (centet), so there is 0.5 inch of the strip light sticking out.
Is this how your look like? Can you please show a picture from above? I would expect the light strip to be flush with the lip, not protruding out.
Any problem with the camera ?
You didn't show plugging in that light bar, Why Not
Where do you run the orange wire?where do they connect ?thanks
Thats looks so simple !!!!!!
how much clearance is needed to clear the license plate? I only have 3/4" from the top of my plate to the oem light. your MY looks like a 2" gap.
I appreciate your install vid!!!
Just installed the Starlink on my 23MYP. Had to use your install vid plus Hansshow’s to complete the install. Nothing too difficult and not really time consuming, but it took me a while because I was watching and rewinding to make sure I didn’t miss a crucial step! Looks great and I’m glad I added these lights to my MY. Next, I’ll be adding the “F1” lights like you have on your Y.
I’m assuming the F1 install is much simpler and faster than the Starlink install?
Did it clear your license plate easily?
@@timothyvo3749 Nope. I modified the plate holder (Dremeled the screw holes to drop the plate down a bit) so it sits just low enough for it to clear.
@@JSinistaProductions thanks for the info - could you elaborate just a bit more? Like were you able to use all 4 mounting holes for the plate holder? And how much dremeljng like a half inch? 3/4”?
Thanks again 👏👏
@JSinistaProductions I have the same car as you, but the light strip is not flush with the lip, where 0.5 inch sticks out. Is this how yours look like? Can you share a photo from above?
@@carlos_siqueiraMine doesn’t fit flush, but it only protrudes maybe 1/8 of an inch.
Any issue with the license plate mounting after installation?
I had a lot of problems with this and ended up removing it!
I removed the entire license plate frame, installed and then reinstalled the license plate no issue whatsoever reinstalling it.
When I installed mine it would not allow the plate and frame. Can you share a photo?
@@jplatis oh I have Rplate digital plates so smaller bezel
So will this not fit a standard USA plate?
Looks awesome 👏👏
Off topic but what is that second camera attached to license tag. I'm interested..link???
Tesla Model Y / 3 NEW Digital Rear View Mirror Camera by Hansshow!
ruclips.net/video/uphqPD41_2o/видео.html
Does it affect warranty on new car?
I installed mine but now my reverse camera lines are out of whack. Do you have any tips on how to fix this?
Did you ever find a solution to this?
I’m in the same boat
Did you ever fix it ?
@@ReconnaissanceLimedid u ever fix it?
@@gambit550
Nah, the camera ends up being slightly lower after install so the guide lines will always look little weird as long as the light strip is installed.
@@ReconnaissanceLime damn .. is it worth doing it then? Hesitant on buying this product thanks for the reply
I got this sent to me by another provider and theirs uses a plugin to the 12V cigarette lighter. Did you do that as well? I see Hansshow’s shows to do this as well. Thanks for the info!
No 12v cigarette lighter for this Hansshow version. Hansshow now customize and test products before release so it’s more refined. Where did you get yours?
@@megawatts I dont want to blast them on the net, apologies as it is a review unit. Thats funny though as Hansshows instructions on their website still show the lighter plug as well! Update time Hansshow! HAHA! Great install vid though sir! Helps us out a lot as usual!
How long was the shipment?
Will u be keeping these on? Or changing it?
Keeping this one for a while as one of our favorite.
@@megawatts Did you have to heat up the adhesive with a dryer?
@@CumBrianFries it was warm out so no but these are strong 3 m the real 3 m not m3 adhesive so very sticky.
I assume nothing for the Model X?
Unfortunately most mods and accessories are focused on Y/3
Terrible install video. Not current with the unit they send out now. No instructions on the 12 v hookup and written instructions say to run it to the left tail light.
How much is it?
See description of this video under 4 hundo
Use our discount code MEGAWATTS
$450 plus about $100 for install. About $550.00 total
@@villagebuzzcom8102 use discount code: MEGAWATTS at checkout and under $400 and you can DIY
Dose this has any effect on the cars warranty or making it void?
You all know how F,ed up Tesla is.
Come on Hansshow that was a Crapy Installtion video 😂
Useless Thatsent show the importent thing with the cable. And Also the cable has to go to the left Not the right.
I hope your product is not as crappy as this insulation video
So weird
Which part?
@@aufpathor112 the proportion of the light bar vs the original led
@@sparkpaul looks fine in person
I like it
Which part
I don’t like the turn signals. Also even though it’s clever it’s just a eye sore that it protrudes out connecting the oem lights to the bar
You can disconnect the turn signal just cut wires to the indicators. Then it works as running lights and brake lights.
@@megawatts Do I have to cut the wires for the indicators? Can't I just not connect them to the tail lights? They're the yellow wires right?
@@megawatts Thanks so much, bro! I'll be patiently waiting. :)
@@megawatts thanks bro I’ll be waiting
@@CumBrianFries just cut the signal wire on the harness and you good no more signal.