Fardriver ND72530/72680 Controller Wiring for QS138 motor in 250cc Enduro conversion

Поделиться
HTML-код
  • Опубликовано: 23 дек 2024

Комментарии • 27

  • @mino6466
    @mino6466 Год назад +1

    Great video. I hope my harness is the same.

  • @Razorcrew_Cole
    @Razorcrew_Cole 2 месяца назад

    Thanks for the video, are you able to put your bike into park? And did you show what wire is park I kind of got lost

  • @HjalmarMadsen
    @HjalmarMadsen 2 месяца назад

    Great and helpfull video we all need. Is turnlight blinker build in the fardriver, or should i connect a blinker??

    • @ElectricOHV
      @ElectricOHV  2 месяца назад +1

      You need to use a blinker relay unless your blinkers have them built in

  • @cheway96
    @cheway96 2 месяца назад

    I have the same harness. Can you help me wire mine

  • @PhoKingLitMedia
    @PhoKingLitMedia 4 месяца назад

    Did you figure out where do the wires come out from after the switch for the headlight? I think I saw where you shown them going into the switch but didn't see where they come out to plug into the light itself. Great work tracking all of this down, very helpful!

    • @ElectricOHV
      @ElectricOHV  4 месяца назад

      time point 7:32 I show the headlight harness.

  • @Babyjok3r77
    @Babyjok3r77 Год назад +1

    I want to wire a light, but for the light connector I don’t know what Each wire does

    • @alexchavosaurus
      @alexchavosaurus 4 месяца назад +1

      I am in the same boat, same with my tail light sensor and speedometer

  • @jeremyball8505
    @jeremyball8505 2 месяца назад

    Did that harness have plugs for 72 volt head lights etc or does all the lights 12 volt ... I know they have 72 lights so if I should use caution when I plug in my lights

    • @ElectricOHV
      @ElectricOHV  2 месяца назад

      normally you run your lights off the 12v power inverter. You can run the 72v power going to the inverter strait to your switch but not many people run 72v lights.

  • @dane4671
    @dane4671 Год назад

    Hi I noticed your phase wires are switched, how come? Was motor spinning in wrong way?

    • @ElectricOHV
      @ElectricOHV  Год назад +1

      Yes the motor was running backwards, some of the videos I watched said all you need to do to change 2 of the phase wires. Turns out you need to change the motor direction in the software. So I changed them back after the video was filmed.

  • @Fpvfreaky
    @Fpvfreaky Год назад

    Hi mate. What wire loom did you get.?
    siaecosys sent me the wrong loom.

    • @ElectricOHV
      @ElectricOHV  Год назад

      There is no identifier on the wire loom, so can't really tell if it's the right one. I think it's kind of generic thou, I needed to modify a few things.

  • @dane4671
    @dane4671 Год назад

    Thanks for the reply
    Yeah my motor is running backwards Iv tried to change the settings in controller but still goes backwards, looks like il have to swap my phase wires around. I got qs138 70h v3 with FarDriver nd72530, I hope I can go forwards not backwards lmao

    • @ElectricOHV
      @ElectricOHV  Год назад

      If you have the fardrive controller there's a setting to switch direction. You need to let it run through its sinking modem it turns for a few seconds in each direction and then when you switch it off and back on it will run in the opposite direction.

  • @andrewaq666
    @andrewaq666 6 месяцев назад

    Hello, did you managed to find the blinkers ? I found that the 3 wire plug Pink Gray Black leads to the blinker flasher unit (it was missing on my harness, yours as well)

    • @ElectricOHV
      @ElectricOHV  6 месяцев назад

      I ended up running my own wires.

  • @cheway96
    @cheway96 2 месяца назад

    Ok. Everything is running now except the display is not reading MPH & voltage😪

  • @ShaunBrenner
    @ShaunBrenner 8 месяцев назад

    What battery specs

    • @ElectricOHV
      @ElectricOHV  8 месяцев назад +1

      I still have the 26ah 72 volt batterey in it going strong. Get me to work and back 4 days a week on 1 charge for over a year now.

  • @EnjoyMoto
    @EnjoyMoto 4 месяца назад

    Bro, your wires from the battery seems too thin compared to the motor wires.

    • @ElectricOHV
      @ElectricOHV  4 месяца назад +1

      That was a temporary wire harness for testing, The wire i'm using 4ga wire on the final set up.

  • @jeremyball8505
    @jeremyball8505 2 месяца назад

    u need a led blinker thingy usually orange and a small box

  • @jeremyball8505
    @jeremyball8505 2 месяца назад

    blinker