Sweet Rajjaa111 I did mine last week. Took all electronics off then sprayed it with water then simple green On it. Then blow it off hit it with WD40 then blow it off. The tires I cut right down the center of the tire. I pull foams out I trim alot of the rubber off except a small part that I can grab. I soak the tires in a can of acid tone over nights. The rubber falls right off. Here we run soft tires all year around. Some of us run one on the exhaust side it's more of a heat sink one. It keeps the fuel cold.
some klunks are not actually a filter they are just a weight but his should be a filter /klunk be sure to look all tanks have a klunk that is what keeps the tube into the fuel or it would float some are filter type some are not just add one if not sure
Bro, you have a treaded faucet...... Chop off a two foot piece of water hose , get the male and female end- fittings from the hardware-store and make a custom short-hose.... Then you can bring the water-gun , INSIDE...... I wish i had a utility-sink.
Yo Gab! I do similar but I put a brass y splitter with the Separate on/off valves on it from harbor freight! And on one side I put about a 4 foot hose with a garden sprayer and use just hot water and you don’t need no cleaner because that water is so Hot( well mines is anyway?) and I have a compressor but I don’t use it. I use my 16 gal wet/dry vac and use the exit side and a funnel tip and that blows much harder, quieter and doesn’t lose pressure!
Stop putting them rims in oven just use acetone they will just come right off but put them in a well ventilated area an the rims will be fine however cut the tire an hold on to them inserts
Nice do the same thing. I use meguiars engine dressing on the car, works and sticks better than silicone. For the cv joints I use motorex mx chainlube spray. Very sticky and doesn't collect dirt( becomes sort of solid). After I put the cv axles in a ultrasonic bath. The water isn't that great for the bearings..
Good to clean engine off before taking apart, with dust dirt on it you have more chances of getting dirt in the engine and leading to problems after reassembling. Just a tip. Keep up the videos though!
I keep my stale fuel in an old fuel bottle, it's good for cleaning one way bearings(I'm sure you had an engine with one at some point) cleaning gummed up fuel out of fuel tanks(don't blame me, that's how they come in) etc.
Where'd you get that air gun with built-in reg? That's a nice tool there; better than my "in-line" type, which is definitely more common. Also, is the point of spraying down the joints, axles, and then the entire car with WD-40 because it displaces water more than being a lubricant?
That's exactly right about the wd40, it moves the water out, here the link for the air gun www.amazon.com/YOTOO-Blowgun-Adjustable-4-5-Inch-Extended/dp/B07KWQ36VN/ref=sr_1_14_sspa?dchild=1&keywords=air+gun&qid=1595458952&sr=8-14-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUExRkhRSzRSN09GOEhGJmVuY3J5cHRlZElkPUEwNDMzMzA0SDNSUUVOMVpVRjNPJmVuY3J5cHRlZEFkSWQ9QTA0MjczODEzOTcwVzZUWjdRRjdKJndpZGdldE5hbWU9c3BfbXRmJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ==
I don't have the time always to take the bearings out an do it everytime I race due to work but I will definitely get them done b4 I race again now I race 1time a month an use my early am start up as my practice time cause I have to travel 1hr plus are better just to race so I leave early in am an get back late plus it depends where I qualify an the main usually b main so with nitro&electric I feel I do ok an enjoy the whole day now my 11 year old wants to race 1/8so I just finished a car for him kyosho tki3 from parts I just had to order the conversion kit an soider up speedo an he is set
WHAT'S UP MY BROTHER, I APPRECIATE YOUR VIDEOS HOPING TO SEE AND MEET YOU AT FLOYD BENNETT FIELD IN BROOKLYN ON JULY 28,2019 . KEEP UP THE GREAT WORK. 👍
Wow tires have holes now them inserts are wet my dude simple green an a rag with tha abrasive brush on rim is great an even with the air now them bearings are wet
Robert Tannenbaum those bearing have been in there for over a year, I’ve been doing it this way for over 10 years never had a problem but hey everyone does things they own way 👍🏾
Mr Geico cool, I have that simple green foam, it works great, I got it months after this video was made, I still want to try that pronto... does it work better then simple green foam?
A rajaa my wife told me earlier that we have a family outing in ct 7 27 so ima try an talk with her about a rental an i can head out to Brooklyn sunday morning keep you posted
@@rajaa111 4 sure but i do want to make if i can but i will keep you posted later enjoy an keep the videos an information coming great stuff an thankx just would like to meet up with you so you can put a face to the conversation an information we share
David Blanchet dude it’s tuff as hell I haven’t broke nothing but a servo arm and I believe because it was cold but nothing else, my losi I had to keep parts on me at all times. If you hear in my last to track videos I keep saying I haven’t broke nothing yet, that’s because I was so surprised
Decided to watch your vid since I ran into you at adrenaline. Your cleaning program made me cringe...I wouldn't do that to some ones car I dislike ...Ok I might!!!! Dig me up at barn or trains...Brian
Brian Faulstick lol... my man, I think trains season opener is April 20th, I’ll be there, but I’ll be hitting trains and adrenaline on the weekends before that, just let me know where you’ll be at
Sweet Rajjaa111 I did mine last week. Took all electronics off then sprayed it with water then simple green On it. Then blow it off hit it with WD40 then blow it off. The tires I cut right down the center of the tire. I pull foams out I trim alot of the rubber off except a small part that I can grab. I soak the tires in a can of acid tone over nights. The rubber falls right off. Here we run soft tires all year around. Some of us run one on the exhaust side it's more of a heat sink one. It keeps the fuel cold.
Soft all year round? Where you located?
Missouri st louis I run at Dirtburners rc track. The one that the driver stand got burnt. And matt Kennedy from Sendit-rc.com
I always use Meguires ultimate wash wax. To clean body’s. And use Alcohol in spray bottle. Q tips shop towels. And finish with plastic cleaner.
God bless you, brother, made my schedule of cleaning and maintaining after you! Keep RC'ing!!
some klunks are not actually a filter they are just a weight but his should be a filter /klunk be sure to look all tanks have a klunk that is what keeps the tube into the fuel or it would float some are filter type some are not just add one if not sure
Bro, you have a treaded faucet...... Chop off a two foot piece of water hose , get the male and female end- fittings from the hardware-store and make a custom short-hose....
Then you can bring the water-gun , INSIDE......
I wish i had a utility-sink.
Allen Traylor nice homie, that’s a great ideal.... I never thought about that one, thanks for the tip 👍🏾👍🏾👍🏾
@@rajaa111
Your a pretty smart dude , it's the simple shit , that we tend to overlook because our brains are always at 100".....
Lol
What do you use to clean the bearings? Thanks!👍🏼
The clunk works good. But when the tank gets below 2 to 3 mm the clunk has trouble getting the fuel.
Man your lucky. Having your own garage and all that equipment to work on the RC's. Those are some wicked buggies damn.
Another great video, just keep them coming bro!👍👍👍👍👍
Great Video man, you got my cleaning skills on balling now, thanks thanks
Great video! Ready to tear down and clean everything now👌🏼
No problem
Yo Gab! I do similar but I put a brass y splitter with the Separate on/off valves on it from harbor freight! And on one side I put about a 4 foot hose with a garden sprayer and use just hot water and you don’t need no cleaner because that water is so Hot( well mines is anyway?) and I have a compressor but I don’t use it. I use my 16 gal wet/dry vac and use the exit side and a funnel tip and that blows much harder, quieter and doesn’t lose pressure!
Stop putting them rims in oven just use acetone they will just come right off but put them in a well ventilated area an the rims will be fine however cut the tire an hold on to them inserts
Nice do the same thing. I use meguiars engine dressing on the car, works and sticks better than silicone. For the cv joints I use motorex mx chainlube spray. Very sticky and doesn't collect dirt( becomes sort of solid). After I put the cv axles in a ultrasonic bath.
The water isn't that great for the bearings..
Buggy looks like new money 👍🏽
crucial118 thanks brotha 👍🏾👍🏾👍🏾
s3 s4 long wear
Good to clean engine off before taking apart, with dust dirt on it you have more chances of getting dirt in the engine and leading to problems after reassembling. Just a tip. Keep up the videos though!
Hey thanks for the vid brother the advise helped me out alot again thank you.
No problem, anytime
Now you have to take bearings out an blow them out along with that center diff an then add oil to them are replace the ones that gritty
I keep my stale fuel in an old fuel bottle, it's good for cleaning one way bearings(I'm sure you had an engine with one at some point) cleaning gummed up fuel out of fuel tanks(don't blame me, that's how they come in) etc.
Almost to a tee how I clean and maintenance my nitros ive always used wd40 it's effective, cheap and you can get it anywhere
Where'd you get that air gun with built-in reg? That's a nice tool there; better than my "in-line" type, which is definitely more common. Also, is the point of spraying down the joints, axles, and then the entire car with WD-40 because it displaces water more than being a lubricant?
That's exactly right about the wd40, it moves the water out, here the link for the air gun
www.amazon.com/YOTOO-Blowgun-Adjustable-4-5-Inch-Extended/dp/B07KWQ36VN/ref=sr_1_14_sspa?dchild=1&keywords=air+gun&qid=1595458952&sr=8-14-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUExRkhRSzRSN09GOEhGJmVuY3J5cHRlZElkPUEwNDMzMzA0SDNSUUVOMVpVRjNPJmVuY3J5cHRlZEFkSWQ9QTA0MjczODEzOTcwVzZUWjdRRjdKJndpZGdldE5hbWU9c3BfbXRmJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ==
Nice video bro 👍 some good info 😎 seen you had a blast by botajel 😅😂 good times
Rc Fun thanks brotha, yeah we had a great time, good people, a lot of laughing
you dont mind getting your bearings wet? and what about where grease is suppose to be applied?
I don't have the time always to take the bearings out an do it everytime I race due to work but I will definitely get them done b4 I race again now I race 1time a month an use my early am start up as my practice time cause I have to travel 1hr plus are better just to race so I leave early in am an get back late plus it depends where I qualify an the main usually b main so with nitro&electric I feel I do ok an enjoy the whole day now my 11 year old wants to race 1/8so I just finished a car for him kyosho tki3 from parts I just had to order the conversion kit an soider up speedo an he is set
You should be taking out center diff cause the brakes will get oil after cleaning
Rajaa111, what is you air hose compressor setup? Great videos by the way, keep them coming!!
I will do a video, its alot to explain, better if you seen it
WHAT'S UP MY BROTHER, I APPRECIATE YOUR VIDEOS HOPING TO SEE AND MEET YOU AT FLOYD BENNETT FIELD IN BROOKLYN ON JULY 28,2019 . KEEP UP THE GREAT WORK. 👍
Ronald Goodman yes sir, see you in New York 👍🏾
Wow tires have holes now them inserts are wet my dude simple green an a rag with tha abrasive brush on rim is great an even with the air now them bearings are wet
Robert Tannenbaum those bearing have been in there for over a year, I’ve been doing it this way for over 10 years never had a problem but hey everyone does things they own way 👍🏾
Well guess ima have to do it that way an see how it works for my kyosho an thankx for the vid an your time to do this vid
I'm not telling you I'm was just saying what works for me an I understand may not work for you but great vids on how to an showing the folks so thankx
It’s all good brotha, I’m glad you shared, I wish I had the time to do it like you that’s the best way,
Super clean did not even look like the same car when you were done
Daniel Kmit thanks brotha 👍🏾👍🏾👍🏾
I had to watch this video again after Sundays track time. She was filthy. Lol
CrucialRC I haven’t washed my cars yet, I’m going to try today
the only difference i use silicone to lube
Great Vid!
Ryan thanks 👍🏾👍🏾👍🏾👍🏾
@@rajaa111 Time for a 5th Scale!
That was the whole shebang
Try using Pronto insead of wd40
Thanks brotha, I will give that a try
Its like simple green foam.Just spray it on and use a brush.
Mr Geico cool, I have that simple green foam, it works great, I got it months after this video was made, I still want to try that pronto... does it work better then simple green foam?
A rajaa my wife told me earlier that we have a family outing in ct 7 27 so ima try an talk with her about a rental an i can head out to Brooklyn sunday morning keep you posted
Robert Tannenbaum no worries brotha, hope you can make it but if not family first
@@rajaa111 4 sure but i do want to make if i can but i will keep you posted later enjoy an keep the videos an information coming great stuff an thankx just would like to meet up with you so you can put a face to the conversation an information we share
What gopro you using
I believe it’s a hero 5 or 6, I’ll check when I get home
Get yourself some brother ! Great video. Would never think to clean em' like this. Very helpful ;]
If your tearing down your cars you should be at the least changing the fuel lines besides replacing an rebuilding them
WD 40 is great, but don't smell so nice.
Great video👍
Henrik Sørensen you can say that again
I must be the only one who likes the smell lol
Ian Darrah lol... you might be playa
1st f@#k it 💪😂💪
Quick question bro.. Is there a reason why, we shouldn't Re-use the fuel thats left in the tank?
dirty may have got into the tank
is the center diff is the same as the losi 4.0
David Blanchet I believe the losi 4.0 center diff is bigger to hold more diff fluid, I think! They do look similar
@@rajaa111 thanks men what do you think about your team associated for bashing did you broke a arm or something weak on them
David Blanchet dude it’s tuff as hell I haven’t broke nothing but a servo arm and I believe because it was cold but nothing else, my losi I had to keep parts on me at all times. If you hear in my last to track videos I keep saying I haven’t broke nothing yet, that’s because I was so surprised
Decided to watch your vid since I ran into you at adrenaline. Your cleaning program made me cringe...I wouldn't do that to some ones car I dislike ...Ok I might!!!! Dig me up at barn or trains...Brian
Brian Faulstick lol... my man, I think trains season opener is April 20th, I’ll be there, but I’ll be hitting trains and adrenaline on the weekends before that, just let me know where you’ll be at