I have one their first printers, the Sidewinder X1, when I remember right, this was a problem with the flat cable not properly connect in the connectors. In very rare case they can burn out a bit. I printed back then some mods to hold the flatcable near the connectors in place. I can see those clips also on this printer. Maybe disconnect and connect the flatcables will help..
Hey there I thought I comment my experience with the printer I also have the plus and I like it! I should point out that I did also have an issue but with the nozzle getting closed I had to get a new fan but support fixed it. I will say there reply times are very wonky and I think that's because there a Chinese company. However the. They work the work great! I have a question about your problem do the z axis moters spin at all? If they do it might mean that the auto level sensor might not be plugged in or is being finicky or not plug-in in it does not know where the bed is.
After this problem Artillery shipped a new motherboard that was replaced. 3 printed item and Z axis crash on printing bad. Assistance Artillery does not answer any more. Do not buy it
A mi me pasaba lo mismo..X3 PLUS.. mi experiencia de como lo solucione ...... 1... actualice el firmware que se encuentra en la misma pagina de artillery.... tambien dan el tutorial pdf de como instalarlo por medio de la sdcard.... 2.. Hay un canal de un argentino que ensena sobre el perfil de cura MetaLWarrioRGames el unico que me sirvio .... tambien ya tengo una configuracion si necesitan para enviarles mi perfil..... 3.. cambie el filamento a uno reconocido creality... Sunlu... etc... 4. ese sonido proviene de la cama... lo que hice fue ... desmontar toda la cama... aflojar un poco las correa de ese eje... desatornillar todo... y hay 2 tornillos que no tienen ese resorte entonces con eso tome la medida... para que el resto queden fijos a esa medida... o los pueden sacar esos dos o acomodar para que toda la cama quede a un solo nivel.. porque nada sirve nivelar las esquinas.. si lo de enmedio es de metal y es una sola medida...... entonces ojo con eso..... ya luego de todo eso mas la actulizacion no he vuelto a tener problema como aquel... 1 de 15 rara vez me suena y presiono el boton de reset... y empiezo ... tambien le cogi el ritmo... al encender... 1.. PRIMERO REINICIAR LOS EJES... 2... CALENTAR .. 3... inserto sdcard y luego imprimir.....
A mi me pasaba lo mismo..X3 PLUS.. mi experiencia de como lo solucione ...... 1... actualice el firmware que se encuentra en la misma pagina de artillery.... tambien dan el tutorial pdf de como instalarlo por medio de la sdcard.... 2.. Hay un canal de un argentino que ensena sobre el perfil de cura MetaLWarrioRGames el unico que me sirvio .... tambien ya tengo una configuracion si necesitan para enviarles mi perfil..... 3.. cambie el filamento a uno reconocido creality... Sunlu... etc... 4. ese sonido proviene de la cama... lo que hice fue ... desmontar toda la cama... aflojar un poco las correa de ese eje... desatornillar todo... y hay 2 tornillos que no tienen ese resorte entonces con eso tome la medida... para que el resto queden fijos a esa medida... o los pueden sacar esos dos o acomodar para que toda la cama quede a un solo nivel.. porque nada sirve nivelar las esquinas.. si lo de enmedio es de metal y es una sola medida...... entonces ojo con eso..... ya luego de todo eso mas la actulizacion no he vuelto a tener problema como aquel... 1 de 15 rara vez me suena y presiono el boton de reset... y empiezo ... tambien le cogi el ritmo... al encender... 1.. PRIMERO REINICIAR LOS EJES... 2... CALENTAR .. 3... inserto sdcard y luego imprimir.....
I have one their first printers, the Sidewinder X1, when I remember right, this was a problem with the flat cable not properly connect in the connectors. In very rare case they can burn out a bit. I printed back then some mods to hold the flatcable near the connectors in place. I can see those clips also on this printer. Maybe disconnect and connect the flatcables will help..
dali si rješio problem? uzeo sam taj printer isti je problem otkrio sam da je to zbog alu vodilica koje nisu simetrične
Muy mala impresora esa, yo tengo una igual y tampoco me funciona. De seguro que no vuelvo a comprar nada mas de Artillery.
Hi, I have the same problem. How did you solve it?
Do not buy it. No assistanze at all
the printer gived more problems? i want to buy that printer but if they give problems i dont want it , now works fine?
Yo llevo años con la Artillery Hornet y cero problemas. Y eso que era la mas sencillita.
Hey there I thought I comment my experience with the printer I also have the plus and I like it! I should point out that I did also have an issue but with the nozzle getting closed I had to get a new fan but support fixed it. I will say there reply times are very wonky and I think that's because there a Chinese company. However the. They work the work great! I have a question about your problem do the z axis moters spin at all? If they do it might mean that the auto level sensor might not be plugged in or is being finicky or not plug-in in it does not know where the bed is.
After this problem Artillery shipped a new motherboard that was replaced. 3 printed item and Z axis crash on printing bad. Assistance Artillery does not answer any more. Do not buy it
Problems are still present and assistance does not reply any more. They are not serious company
A mi me pasaba lo mismo..X3 PLUS.. mi experiencia de como lo solucione ...... 1... actualice el firmware que se encuentra en la misma pagina de artillery.... tambien dan el tutorial pdf de como instalarlo por medio de la sdcard.... 2.. Hay un canal de un argentino que ensena sobre el perfil de cura MetaLWarrioRGames el unico que me sirvio .... tambien ya tengo una configuracion si necesitan para enviarles mi perfil..... 3.. cambie el filamento a uno reconocido creality... Sunlu... etc... 4. ese sonido proviene de la cama... lo que hice fue ... desmontar toda la cama... aflojar un poco las correa de ese eje... desatornillar todo... y hay 2 tornillos que no tienen ese resorte entonces con eso tome la medida... para que el resto queden fijos a esa medida... o los pueden sacar esos dos o acomodar para que toda la cama quede a un solo nivel.. porque nada sirve nivelar las esquinas.. si lo de enmedio es de metal y es una sola medida...... entonces ojo con eso..... ya luego de todo eso mas la actulizacion no he vuelto a tener problema como aquel... 1 de 15 rara vez me suena y presiono el boton de reset... y empiezo ... tambien le cogi el ritmo... al encender... 1.. PRIMERO REINICIAR LOS EJES... 2... CALENTAR .. 3... inserto sdcard y luego imprimir.....
I have the same problem with the X3plus
A mi me pasaba lo mismo..X3 PLUS.. mi experiencia de como lo solucione ...... 1... actualice el firmware que se encuentra en la misma pagina de artillery.... tambien dan el tutorial pdf de como instalarlo por medio de la sdcard.... 2.. Hay un canal de un argentino que ensena sobre el perfil de cura MetaLWarrioRGames el unico que me sirvio .... tambien ya tengo una configuracion si necesitan para enviarles mi perfil..... 3.. cambie el filamento a uno reconocido creality... Sunlu... etc... 4. ese sonido proviene de la cama... lo que hice fue ... desmontar toda la cama... aflojar un poco las correa de ese eje... desatornillar todo... y hay 2 tornillos que no tienen ese resorte entonces con eso tome la medida... para que el resto queden fijos a esa medida... o los pueden sacar esos dos o acomodar para que toda la cama quede a un solo nivel.. porque nada sirve nivelar las esquinas.. si lo de enmedio es de metal y es una sola medida...... entonces ojo con eso..... ya luego de todo eso mas la actulizacion no he vuelto a tener problema como aquel... 1 de 15 rara vez me suena y presiono el boton de reset... y empiezo ... tambien le cogi el ritmo... al encender... 1.. PRIMERO REINICIAR LOS EJES... 2... CALENTAR .. 3... inserto sdcard y luego imprimir.....