Feeds through the ecotank I have easily (eat-2400) 🙋♀️ cold peel works best and I find 320° F for 40 seconds works well for my press I burned the cotton any higher than 340° 🤩 love your shirt and your technique 💯
so when you took the paper out it went straight to your printer the way you took out. so easy i was trying to see if it says front back on the sheets lol. thanks for your video now i know how to use mines
Thanks I got it to work by putting painters tape on the back across the end and a piece down the middle like a letter T... this is the only way that works for me
Thank you for the video testing this product. I'm curious why under the Advanced Tips the first one is: "Leave film to dry fully before apply the powder." Why is that? When normally instructions are to apply powder right away after printed.
Did you wait for the ink to dry? The advanced tips section of the paper that came with the kit says to buy I don’t find it drying even after 10 minutes!
Thank you for your review on this DTF powder and transfer film. I may have to give it a try. Is there an odor with this powder? I have used the brands that Crystal Ann demonstrated and tend to lean towards one more than the other because I had better results.
I just printed a small square of my design and the ink doesn't look solid. It looks kind of bubbly if that makes sense. I'm afraid to do the whole page I don't want to waste a bunch of ink. 30 minutes later the ink is still wet and I can smear it right off with my finger.
I just purchased the 11x17 of this and I am so disappointed. I have tried every trick and I can not get it to feed correctly into my Epson ET 15000. I have used a different brand of DTF paper that had no issues feeding. I was really looking forward to using this as I need the larger size sheets but I dont know what other tricks to try to get this film to be recognized and feed correctly. anyone else besides me have this issue. I did see someone else complain about this on Amazon but that didn't find a resolution either.
I have just bought this product, I am having so much trouble feeding it through my printer, I've tried so many ways. you said at the end that it went thru by putting a stack of paper behind it. I'll give this a try. Did you not tape it to copy paper?
What I have found works is putting a layer of like Lionel like shelf paper removable vinyl stuff like that on the back of the film and then it goes through take it off and then put it off to the side and try to use it again a different I tried putting just a little ways up and it always printed just to I tried taping the paper to the back. Didn't work I tried everything
No this dtf hack is for light colored shirts, unless you use a white htv background. I'm planning to make a video trying that out. I'm just waiting on my order to come in.
What is confusing to me, as they say to let the ink dry before putting on the powder? Every other video or tutorial I’ve ever seen said to do it while it’s wet.
For my 2720 printer, I use the same as my regular sublimation prints. Presentation paper matte, high quality. You can go into tour maintenance settings & maybe reduce the saturation & see it that helps.
Unfortunately you cannot. Because the ink is transparent, its always best to use light color shirts, but there are other products out there that you could try. I've done it once, and it was a mess, but with practice, it can come out cool too.😊
For my small printer I use presentation paper matte, high quality, adobe RGB 2.2 gamma, mirrored. I can't get the right settings for my large format printer. Its frustrating
@@mgcraftsandmore My ET 2720 worked perfectly without any adjustments. My new ET 8550 is giving me gray hairs with the settings setup with Silhouette, a work still in progress with the DTF Hack. If you are getting started I would definitely recommend the 2720. Mines broke after 2 years and I wanted a larger print ET Epson.
@MiMySlots yes, I actually have it and have rarely had issues. I wanted to print bigging images so I got the 15000. It's just when I do the DTF. It's frustrating.
This is a Tusy auto press, but it was only out a couple of months when I purchased it off amazon, and have been having problems. You definitely want to do your research. I can't recommend it with some of the issues I've been having.
![[#2024MAMA] BIGBANG (빅뱅) - 뱅뱅뱅 (BANG BANG BANG) + FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/EQsYfiPR9uM/mqdefault.jpg)
New subbie starting my journey to fundraise for my daughter’s liver transplant. I’m taking notes and appreciate your content
Thank you and welcome! Happy to havw you here. 😊
Feeds through the ecotank I have easily (eat-2400) 🙋♀️ cold peel works best and I find 320° F for 40 seconds works well for my press I burned the cotton any higher than 340° 🤩 love your shirt and your technique 💯
Thank you so much.
so when you took the paper out it went straight to your printer the way you took out. so easy i was trying to see if it says front back on the sheets lol. thanks for your video now i know how to use mines
Oh good. I'm happy to help.
Thanks I got it to work by putting painters tape on the back across the end and a piece down the middle like a letter T... this is the only way that works for me
Thank you for the video testing this product. I'm curious why under the Advanced Tips the first one is: "Leave film to dry fully before apply the powder." Why is that? When normally instructions are to apply powder right away after printed.
Yeah, i didn't do that, and I didn't have issues bcuz of that
Thanks for the video they said this kit only worked with white shirts im guessing it works with all color fabrics since this is not a white shirt .
It works well with light colors, but will not show up on black or other really dark colors.
@@mgcraftsandmore how long would you say the powder would last? did it last for a while ?
@shonondabeats618 yes, it does last quite a long time.
Did you wait for the ink to dry? The advanced tips section of the paper that came with the kit says to buy I don’t find it drying even after 10 minutes!
No I did not. You can give it a minute, but for me it doesn't make a difference.
Thank you for your review on this DTF powder and transfer film. I may have to give it a try. Is there an odor with this powder? I have used the brands that Crystal Ann demonstrated and tend to lean towards one more than the other because I had better results.
@nancyKluz I didn't notice any smell at all, which I'm glad about because I get migraines & that type of smell would probably be a trigger.
Thank you for the quick reply. That is good to know. :)
What's the temperature you use on the grill
It has 1-4 on the dial, so i had it on 2. I can't remember the temps right off the bat, but I think that was the perfect temp for this.
Thank you, I have one and the temperature, it start at 200 , 400 and the last one it's min after the 400
What temperature, did you use for the grill
I have the epson 2803
Can you tell me what is the diffence between DTF Ink film and DFT film for Sublimation. Love your video
I've only used DTF film & powder using sublimation ink. There is such a thing as DTF ink, but I can't talk to that.
@mgcraftsandmore thank you any way.
You're welcome
I just printed a small square of my design and the ink doesn't look solid. It looks kind of bubbly if that makes sense. I'm afraid to do the whole page I don't want to waste a bunch of ink. 30 minutes later the ink is still wet and I can smear it right off with my finger.
@corinnebeth5525 are you trying to print with an inkjet or sublimation printer? That makes all the difference.
Can you use other powders with cendale I use tons of their stuff
I have different powders as well. I would just use the directions for the specific powders.
I was just curious thanks cendale is a great product@@MonicaGarza893
I just purchased the 11x17 of this and I am so disappointed. I have tried every trick and I can not get it to feed correctly into my Epson ET 15000. I have used a different brand of DTF paper that had no issues feeding. I was really looking forward to using this as I need the larger size sheets but I dont know what other tricks to try to get this film to be recognized and feed correctly. anyone else besides me have this issue. I did see someone else complain about this on Amazon but that didn't find a resolution either.
I have to tape them to a paper, as it doesn't want to feed. I don't have these issues with my smaller printer. It is frustrating.
I have just bought this product, I am having so much trouble feeding it through my printer, I've tried so many ways. you said at the end that it went thru by putting a stack of paper behind it. I'll give this a try. Did you not tape it to copy paper?
After putting a thick stack of paper, I haven't had to tape it to anything.
What I have found works is putting a layer of like Lionel like shelf paper removable vinyl stuff like that on the back of the film and then it goes through take it off and then put it off to the side and try to use it again a different I tried putting just a little ways up and it always printed just to I tried taping the paper to the back. Didn't work I tried everything
That is nice
Amazing tutorial video🤩Thanks for your kind sharing!!
Thank you. I appreciate you for trusting me to try out your products.
How about on dark shirt like black, does the design is still visible?
No this dtf hack is for light colored shirts, unless you use a white htv background. I'm planning to make a video trying that out. I'm just waiting on my order to come in.
What size did you use to print the image
I believe this one was an A4 size.
What is confusing to me, as they say to let the ink dry before putting on the powder? Every other video or tutorial I’ve ever seen said to do it while it’s wet.
I've always dine it when the ink is wet. Some products may have different instructions, so you really need to watch for that.
What was your print settings? I keep getting black lines 😢
For my 2720 printer, I use the same as my regular sublimation prints. Presentation paper matte, high quality. You can go into tour maintenance settings & maybe reduce the saturation & see it that helps.
Hello new to your channel, can you use a dark or black shirt with this hack?
Unfortunately you cannot. Because the ink is transparent, its always best to use light color shirts, but there are other products out there that you could try. I've done it once, and it was a mess, but with practice, it can come out cool too.😊
@@mgcraftsandmore Thank you
Can I use a inkjet printer?
Yes, but I suggest you watch my other video.
ruclips.net/video/_t_3pk-h2Fs/видео.htmlsi=lDs56P-SNU8npp4P
What settings did you put on your printer? For the life of me I can't get it to work
For my small printer I use presentation paper matte, high quality, adobe RGB 2.2 gamma, mirrored. I can't get the right settings for my large format printer. Its frustrating
...although it may be different if you have a different printer. Mine is an Epson ecotank 2720
@@mgcraftsandmore My ET 2720 worked perfectly without any adjustments. My new ET 8550 is giving me gray hairs with the settings setup with Silhouette, a work still in progress with the DTF Hack. If you are getting started I would definitely recommend the 2720. Mines broke after 2 years and I wanted a larger print ET Epson.
@MiMySlots yes, I actually have it and have rarely had issues. I wanted to print bigging images so I got the 15000. It's just when I do the DTF. It's frustrating.
Is that regular epson ink or sublimation?
This is sublimation ink.
Hello I have a question
Please ask.
@@mgcraftsandmore can I use A3 paper
@yoanavlogs875 yes you can if you have a larger format printer.
@@mgcraftsandmore I have sawgrass 1000
What ink do you use?
I use Cosmos Ink sublimation ink in one printer, and on the other, I use A-Sub sublimation ink.
@@mgcraftsandmore Which ink do you like best?
@lynxlady5355 I love Cosmos Ink. I have that in one of my printers and A-Sub in the other. They're both great.
What kind of press is that?
This is a Tusy auto press, but it was only out a couple of months when I purchased it off amazon, and have been having problems. You definitely want to do your research. I can't recommend it with some of the issues I've been having.
@@mgcraftsandmore thanks for the quick reply.
You're welcome.