Oil filter bypass isn't going to change a thing. Even if it was stuck open it would only bypass the filter. It has no effect on oil pressure. The pressure relief in the oil pump could certainly have an effect but it wouldn't increase with RPM if that was stuck open.
Or that secret 1/2 oil plug might be missing?? If you look down oil send hole u should see it down there , Put a thin wire down there should go down about 10 inches or so, if it goes past the oil filter housing its missing.
Just wondering is the pickup tube tight how about the torque on the oil pump bolts I would think you double checked the rod and main clearences right?...
Have you tried switching gauges.i noticed the oil pressure was rising when you reved it.. if it was i could not see it..I would try strait 40 or vr50 weight. Just some thoughts
I made a comment about the distributor, but took it down.. I was thinking they going to think I’m crazy lol.. the second part of my comment with clearances go to a little heavier weight oil and last thing I mentioned was a leaking rear cam bearings.. I hope you find it.. it looked like you got up to 25 though
i tried to find the rest bof your message and couldnt iguess they will think 2 of us are crazy im going from 10/30 to 15/40 and see what that does the distributor swap did pick it up around 5 psi
I have a 383 stroker in a 34 Ford that started doing the same thing change the oil and went to a heavier weight worked a little better but still not where it should be. Check the oil pump. Everything looks good don’t know what to do next.
Man I went to 15/40 oil and its up to 25 psi hot idling I'm not happy with it some guys tell me they are running 20/50 oil and happy mine is a 1 price rear seal block and from what I've read they don't hold as much oil pressure as the old blocks do
Try the primer again. See if it’s same or better. Maybe try adding a quart of oil. Did you check pickup to pan clearance?
the pickup to pan clearance is 1/2 inch
I heard it ok to run around 7psi for every 1000 rpm.
Nobody wants to hear, cam bearings not tight enough.
15/40gives it 25 psi hot I'm not happy with it but it's doable
Oil filter bypass isn't going to change a thing. Even if it was stuck open it would only bypass the filter. It has no effect on oil pressure. The pressure relief in the oil pump could certainly have an effect but it wouldn't increase with RPM if that was stuck open.
Good video. Hope you find the issue!!
That gauge sure seams lazy maybe try another one
that is the second gauge
Or that secret 1/2 oil plug might be missing?? If you look down oil send hole u should see it down there , Put a thin wire down there should go down about 10 inches or so, if it goes past the oil filter housing its missing.
Put in a stiffer oil pressure relief valve Spring.
Just wondering is the pickup tube tight how about the torque on the oil pump bolts I would think you double checked the rod and main clearences right?...
all the clearances were 3 to 3,5 thou oilpickup is 1/2 off the pan and welded
Man, I hope it’s just the oil bypass sticking .
Maybe try another gauge before tearing into it just to make sure if not yeah try checking the bypass.
chevy i replaced the gauge they both read the same so the bypass is next
@@oldmanintheshopbuiltnotbou8726 👍
So did you ever get it was it the bearings? Let me no good video
You have internal problems, the idle was terrible. Check the timing, did you degree the cam? Pull the pan and check the bearings.
Joe the motor is fine I did pull the pan and all clearances were 2 thou. To 3 thou
Have you tried switching gauges.i noticed the oil pressure was rising when you reved it.. if it was i could not see it..I would try strait 40 or vr50 weight. Just some thoughts
i did replace the gauge and they both read the same im going to check the bypass tomorrow and then maybe try 15/
trying some 15/40 instead of 10/30
I got no answers hopefully the bypass fixes it old man
lenxy i sure hoping it does
I made a comment about the distributor, but took it down.. I was thinking they going to think I’m crazy lol.. the second part of my comment with clearances go to a little heavier weight oil and last thing I mentioned was a leaking rear cam bearings.. I hope you find it.. it looked like you got up to 25 though
i tried to find the rest bof your message and couldnt iguess they will think 2 of us are crazy im going from 10/30 to 15/40 and see what that does the distributor swap did pick it up around 5 psi
Howdy everyone 😀 😄
hey guys
Maybe the bypass is stuck
im going to try that tomorrow russell
I have a 383 stroker in a 34 Ford that started doing the same thing change the oil and went to a heavier weight worked a little better but still not where it should be. Check the oil pump. Everything looks good don’t know what to do next.
Man I went to 15/40 oil and its up to 25 psi hot idling I'm not happy with it some guys tell me they are running 20/50 oil and happy mine is a 1 price rear seal block and from what I've read they don't hold as much oil pressure as the old blocks do
Use a heavier weight oil
How about the o ring on the oil pump pickup tube?
this setup doesnt have a o ring in the pickup