The coax cable repair shown will introduce an impedance mismatch at the location where it is spliced. Probably not an issue on receive but could be an issue for a transmitter. To keep the impedance you'd have to use BNC or N type connectors instead of the splice shown.
Ad 1: mindblowing Ad 2: the twist and extra stress can damage the metal wires. However the risk would be very small, no problem. Ad 3: nice idea! Ad 4: this might work if the remote can operate with just single battery. Which is sometimes the case, there are step up circuits. But even then a wire would be better than a pencil. Graphite has high resistance. Ad 5: another nice idea Ad 6: the last option is not better than the first one. The second option works better because there is longer path of the wire which would need to slide. Friction is therefore much higher and so the force needed to pull it out is higher. The third option does not extend the path much. Only the small part on right needs to move. And once it is pulled out then only the small part at left has to move. They don't get stressed at once. The force therefore does not go up much. And having two pieces of wire next to each other could actually decrease the friction if the metal piece is not reasonably flat. Option 3 is not an improvement. Use options 1 or 2. Ad 7: this one often works. What you do here is replacing a LED by a wire. LEDs cause a voltage drop. Wire does not. In order to provide a light there must be a current flowing through the LED. Too high current means it burns out. Now let's imagine you have power source of 48V and you use 12 LEDs where each one has 3V drop. Combined they do 36V drop. Each needs 20mA of current. To limit the current you use a resistor which would be 12V / 20mA = 600 ohm. The resistor would dissipate 0.24W of heat. Now, to the point. You replace one LED by a wire. So the voltage drop of the remaining 11 LEDs is only 33V. The voltage on the resistor is up to 15V. It will give current of 25mA and power dissipation would be 0.375W. Will the LEDs survive that current increase? And won't the resistor overheat? Real situation is even worse as the manufacturers want to decrease the power lost on the resistors and so use LEDs which have voltage drop lower than the source, but still as closest to it as possible. Replacing even a single LED by a wire could then easily mean the resistors would overheat and bad things could happen. Do not do this unless you have the schema and skills to evaluate the risk involved. Ad 8: works on non-critical wiring. Which means 99.9% of wiring around us. No problem with this either. Ad 9: another perfect idea!
Uzb; Ad 8: men qilib ko‘rganman, tasma chiroqda 50 ta LED bor edi, 2 tasi singan edi, olib tashlab sim bilan ulab qo‘yganman, ishlab ketgan Eng; Ad 8: i tried it, the strip light had 50 leds, 2 were broken, i removed and rewired it, it worked
Also, proper plugs have strain relief clamps that are designed to clamp onto the isolation and hold it in place. I don't know in what kind of backwards place you live in that you even HAVE plugs like that, but the only receptacle this plug should be in is a trash bin.
Two things that surprise me: European plugs don't have cable clamps, and every household apparently has two different sizes of heat-shrink tubing lying around, and a heat gun, soldering iron and solder, but no proper co-ax connectors.
교수님 영상 잘 보겠습니다 그런데요 드릴 만드는법 전선 빨강색 파란색 노란색이 무슨선이고 스위치안쪽에 어떻게 연결해야 싀의치가 켜지고 꺼지는 역할을 확실하게 알려주시면 핫국에 인기가 많을거 같습니다 다른영상은 한국어도 않하고 상세하게 않알려 주니 보기가 힘들었어요 영상 잘보고 갑니다
I'm glad you enjoyed this project! Feel free to connect with other viewers in the comments section and share your results. It's always inspiring to see what everyone creates
I haven't tried #4 , so I cant really say it won't work. but in theory , it shouldn't . because, not only are you cutting down on the operating voltage by 1.5 volts, using one battery, but then by using a pencil lead, which has electrical resistance, you are cutting the already halved voltage down even further. But if your device used AA you can use a AAA by putting a small ball of aluminum foil on the flat end of the AA battery. and it will work. but you might have to pack a little paper between the batteries so they wont move around and lose connection . AAA , AA and D sized batteries are very close to the same voltage just different sizes. to fit the battery compartment, and size of the device.
While watching this spectacular video, I can't help but wonder about one thing: I own rental properties, and I perform all the maintenance and repairs myself. To keep things organized, I have bins with parts and tools seperated by category: Plumbing, Electrical, etc. That's where my question comes from: Do people outside of the US have a kitchen "Junk Drawer" ? I'd welcome input from everyone, all around the world. If you know someone outside 5US, I'm eager to hear their answer. GREAT video !!!!!
@GB-go6gp - From my experience as a 64 y.o who lives in Australia, I find usually women of older generations have these kitchen junk draws, or males who are not handyman types. We had one at home of sorts ( metal biscuit tin full of junk and household fittings ( picture hooks, wire, string, insulation tape, batteries, screws & tacks for carpet etc ). When I was a teen, Dad & I used it most of all. However, if you have a male in the house who is the handyman type ( like me ) these days he's most likely got access to a garage full of tools with bits & pieces.
@@kimbal1958 Well, I'm certainly not an older woman ("well I can't just call you Man"). I am however, the aforementioned handy-man, and I have a well organized, albeit small junk drawer. While I do have a garage full of tools, the small, unpowered tools that I use frequently reside in my junk-drawer.
Hello, you are such a nice person to have left me a comment! With a dream to contribute to making the world a better place, I really need good and useful ideas and solutions! If you have any other great ideas please share with me! Together we will make this world a better place! Wishing you good health, success and happiness! Thank you very much!
As a 37yo frenchman, I keep everything in several toolboxes: one for screws, screwdrivers, nails, hammers, drill bits, and an other one for all electrical, mechanical and plumbering stuff (wrenches/ratchets, soldering irons, electric tape, pliers...), a 3rd one for all that doesn't fit in the 2nd one, and all the other boxes are for my powertools (from drill to impact wrench).
6:50 no it's wrong. you can't just connect the chain instead of replacing the dead LED element. This is a common mistake in all such video tutorials. Because it will increase the brightens due to raising of load to other LEDs, making them suffer more and very soon one or more will be dead too.
The first one only works because they removed the wire opposite the way they put it on. If the pipe had installed over a straight wire this would not have worked.
Мм... Обожаю. Провод, который надо показать, что плохо закреплëн выдернул с видимым услием, а те, которые, типа, норм, те так... Слегка потряс из стороны в сторону. Ну, показал, ну молодец... Нет, безусловно, чем больше площадь провода, которая придавливается, тем лучше он будет держаться, но показывать это так убого ещё постараться надо.
Uzun süre kullanmadığım Raks vantilatörümü açtığımda hıç dönmedi. Motoru söküp şaftı hem önden hem arkadan yağladım. Dönmeye başladı ancak ilk açılışta hızlı dönüp😅 sonra yavaş dönmeye başlıyor. Ne arızası olabilir.
Ótimo vídeo! Gostei demais do ritmo dado, geralmente são cortadas várias etapas do processo para deixar o vídeo mais rápido, mas o formato pelo qual optou me proibiu de assisti-lo em velocidade acelerada o que ajudou e muito na absorção das dicas. Também gostei dos textos inseridos ao longo do vídeo. Parabéns pela coragem de fazer diferente!!!
Def not going to want to do the LED light fix, that increases the voltage drop across the rest of the LED's in the circuit, might overheat, or start a fire.
on the first LED fix it works, i have fixed LEDs over my room and work table for like... 2 or 3 years already. But with a 2nd LED fix in a few months the bulb melts (tried it with an independant connection) ofc the 1st fix must be made properly, 1 option is like in the video and a 2nd option can be using string wires (thin as hair) to secure the soldering iron
@@creationholic101 Please do not make videos about electrics as you do not have in-depth knowledge of imitating people and endangering their health and life. In Germany you would have received an injunction and paid a large fine.
0:37 Das ist wirklich meisterhaft, eine Litze ohne Endhülse verklemmen. 3:21 Ich weiß jetzt nicht, wieso der Hersteller zwei Batterien benutzt, wenn doch eine reicht. Wieso 3 Volt, wenn das Gerät mit 1.5 Volt auch funktioniert.
Зачем портить карандаш? Долго на 1 батарейке пульт не проработает, мощность его снизилась. Проще было помять старые батарейки или заменить одну старую, на одну новую. Если уж в магазин так не хочется идти.
чё за бред с пультом, во первых от 1.5в он скорее всего даже не заработает или будет очень слабый сигнал, а во вторых грифель не проводит ток Лампочка с коротышом место диода проработает от силы неделю, потом сгорит ещё один диод, т.к. на все оставшиеся диоды будет подано больше тока
@@creationholic101 no problem man! Just doing my part in interacting so you get ahead in the algorithm. Controversy gets interactions, which gets recommendations, which gets views. Best of luck in growing your channel
❗Please enable subtitles in your language 🙋🏼♀ Thanks for watching 😋🤗😘
Franca😢
¹¹¹
😂@@JacquesLucet-v2p
4: No need to cut a pencil. You can use one old battery instead.
Hello! thanks for your recommendation. Wish you all the best!
The coax cable repair shown will introduce an impedance mismatch at the location where it is spliced. Probably not an issue on receive but could be an issue for a transmitter. To keep the impedance you'd have to use BNC or N type connectors instead of the splice shown.
Hello! thanks for your recommendation. Wish you all the best!
@vk3fbab Using a strong enough transmitter makes this much less of a problem though because none of your pets will ever chew a cable again 😉
Ad 1: mindblowing
Ad 2: the twist and extra stress can damage the metal wires. However the risk would be very small, no problem.
Ad 3: nice idea!
Ad 4: this might work if the remote can operate with just single battery. Which is sometimes the case, there are step up circuits. But even then a wire would be better than a pencil. Graphite has high resistance.
Ad 5: another nice idea
Ad 6: the last option is not better than the first one. The second option works better because there is longer path of the wire which would need to slide. Friction is therefore much higher and so the force needed to pull it out is higher. The third option does not extend the path much. Only the small part on right needs to move. And once it is pulled out then only the small part at left has to move. They don't get stressed at once. The force therefore does not go up much. And having two pieces of wire next to each other could actually decrease the friction if the metal piece is not reasonably flat. Option 3 is not an improvement. Use options 1 or 2.
Ad 7: this one often works. What you do here is replacing a LED by a wire. LEDs cause a voltage drop. Wire does not. In order to provide a light there must be a current flowing through the LED. Too high current means it burns out. Now let's imagine you have power source of 48V and you use 12 LEDs where each one has 3V drop. Combined they do 36V drop. Each needs 20mA of current. To limit the current you use a resistor which would be 12V / 20mA = 600 ohm. The resistor would dissipate 0.24W of heat. Now, to the point. You replace one LED by a wire. So the voltage drop of the remaining 11 LEDs is only 33V. The voltage on the resistor is up to 15V. It will give current of 25mA and power dissipation would be 0.375W. Will the LEDs survive that current increase? And won't the resistor overheat? Real situation is even worse as the manufacturers want to decrease the power lost on the resistors and so use LEDs which have voltage drop lower than the source, but still as closest to it as possible. Replacing even a single LED by a wire could then easily mean the resistors would overheat and bad things could happen. Do not do this unless you have the schema and skills to evaluate the risk involved.
Ad 8: works on non-critical wiring. Which means 99.9% of wiring around us. No problem with this either.
Ad 9: another perfect idea!
Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!
Replying to @ karolberanek1007
DARZHNARZHERFLARVERSHARVER?
DARZHNARZHERFLARVERSHARVER?
Uzb; Ad 8: men qilib ko‘rganman, tasma chiroqda 50 ta LED bor edi, 2 tasi singan edi, olib tashlab sim bilan ulab qo‘yganman, ishlab ketgan
Eng; Ad 8: i tried it, the strip light had 50 leds, 2 were broken, i removed and rewired it, it worked
Thank you so much for explanations! Nice video and it Is even more useful having in mind your comments.
@ number 2, just buy a proper plug with tension relief. It’s default on any non-garbage plug.
Thank you for sharing your feedback and expressing your perspective
And use proper wires )))
Putting uncrimped stranded wire into a screw terminal is enough to ban you from any kind of master title for all eternity.
Also, proper plugs have strain relief clamps that are designed to clamp onto the isolation and hold it in place. I don't know in what kind of backwards place you live in that you even HAVE plugs like that, but the only receptacle this plug should be in is a trash bin.
Thank you for sharing your feedback and expressing your perspective
Nunca vi un control remoto que pudiera funcionar con la mitad de la tension de diseño
I tried it and it works, you can try it
Semua teknik di konten video ini super kereeeeen
😊ดีมากครับ ทำให้ทราบวิธีที่มีประโยชน์ แต่ข้อ 4 มีใหม่ 1 ก้อน ก็ใส่ไป ใช้งานได้ปกติแค่หมดเร็ว ข้อสุดท้าย ดีครับเพราะเหมาะกับช่างก่อสร้าง ช่างไฟ ช่างปะปา โดยเฉพาะถูกจ้างให้ไปทำตอนมีผู้อาศัยแล้ว ไม่ใช่บ้านใหม่ จะได้สะอาด😊
Hello! thanks for your comment. Wish you all the best!
Tipp 2. solche Stecker dürfen in der EU nicht verkauft werden. Natürlich Arbeiten ohne Adernendhülsen. Die Schraubendrehergröße stimmt auch nicht.
Es ist erschreckend, was hier für „clever“ verkauft wird.
LED löten, einphasig abgeschaltet… Top-Idee! 🤦🏻♂️🤦🏻♂️
Thank you for sharing your feedback and expressing your perspective
very good
Welcome to Creation Holic channel! Hope you have a good time while watching the video!
Two things that surprise me: European plugs don't have cable clamps, and every household apparently has two different sizes of heat-shrink tubing lying around, and a heat gun, soldering iron and solder, but no proper co-ax connectors.
교수님 영상 잘 보겠습니다 그런데요
드릴 만드는법 전선 빨강색 파란색 노란색이
무슨선이고 스위치안쪽에
어떻게 연결해야 싀의치가 켜지고 꺼지는
역할을 확실하게 알려주시면 핫국에 인기가 많을거 같습니다
다른영상은 한국어도 않하고 상세하게 않알려
주니 보기가 힘들었어요
영상 잘보고 갑니다
❗Please enable subtitles in your language 🙋🏼♀ Thanks for watching 😋🤗😘
مبدع والله وننتظر منك المزيد وبارك الله فيك
Hello! welcome to Creation Holic channel. I am very happy to read your comment. Wish you have a nice day!
#6 the gentle pull makes a huge difference.
Thank you for watching
Trik dan tips yg sangat menakjubkan
"Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"
Excelente trabajo
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
شكرا لكم . الحيلة الأخيرة ماذا بعد ثقب القارورة وتثبيتها بالجدار ؟
Hello! thanks for your recommendation. Wish you all the best!
오~ 전기 작업 개꿀팁!
I'm glad you enjoyed this project! Feel free to connect with other viewers in the comments section and share your results. It's always inspiring to see what everyone creates
I am spaniard, from Cartagena Spain. ... and I am very pleased for your teaching videos ... thanks a lot
Welcome to Creation Holic channel! Thank you so much for your support
Ini sangat bagus sekali
Thank you for watching
Tuyệt vời 🎉❤.vietnam
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Step 4.....JUST USE THAT EMPTY BATTERY !!
I tried it and found it very good
두번째 반단선 위험 있습니다. 전선화재 위험. 전선은 구부리지 않은 일직선이 가장 이상적입니다.
Hello! thanks for your comment. Wish you all the best!
I haven't tried #4 , so I cant really say it won't work. but in theory , it shouldn't .
because, not only are you cutting down on the operating voltage by 1.5 volts,
using one battery, but then by using a pencil lead, which has electrical
resistance, you are cutting the already halved voltage down even further.
But if your device used AA you can use a AAA by putting a small ball of
aluminum foil on the flat end of the AA battery. and it will work. but you might
have to pack a little paper between the batteries so they wont move around and
lose connection . AAA , AA and D sized batteries are very close to the same voltage
just different sizes. to fit the battery compartment, and size of the device.
I use it in case I can't buy a replacement
Thanks
Cám ơn bạn.Rất tiện ích
Hello. Welcome to my channel. Thank you for your feedback!
Probing the light at 6:20 seems very dangerous as you are dealing with mains voltages without much protection.
Yes.. terrible
I used safety protection and my body did not come into contact with the ground
Mẹo rất hay!
Welcome to Creation Holic channel! Thank you so much for your support
While watching this spectacular video, I can't help but wonder about one thing: I own rental properties, and I perform all the maintenance and repairs myself. To keep things organized, I have bins with parts and tools seperated by category: Plumbing, Electrical, etc. That's where my question comes from: Do people outside of the US have a kitchen "Junk Drawer" ?
I'd welcome input from everyone, all around the world. If you know someone outside 5US, I'm eager to hear their answer.
GREAT video !!!!!
@GB-go6gp - From my experience as a 64 y.o who lives in Australia, I find usually women of older generations have these kitchen junk draws, or males who are not handyman types. We had one at home of sorts ( metal biscuit tin full of junk and household fittings ( picture hooks, wire, string, insulation tape, batteries, screws & tacks for carpet etc ). When I was a teen, Dad & I used it most of all.
However, if you have a male in the house who is the handyman type ( like me ) these days he's most likely got access to a garage full of tools with bits & pieces.
@@kimbal1958 Well, I'm certainly not an older woman ("well I can't just call you Man"). I am however, the aforementioned handy-man, and I have a well organized, albeit small junk drawer. While I do have a garage full of tools, the small, unpowered tools that I use frequently reside in my junk-drawer.
Hello, you are such a nice person to have left me a comment! With a dream to contribute to making the world a better place, I really need good and useful ideas and solutions! If you have any other great ideas please share with me! Together we will make this world a better place! Wishing you good health, success and happiness! Thank you very much!
As a 37yo frenchman, I keep everything in several toolboxes: one for screws, screwdrivers, nails, hammers, drill bits, and an other one for all electrical, mechanical and plumbering stuff (wrenches/ratchets, soldering irons, electric tape, pliers...), a 3rd one for all that doesn't fit in the 2nd one, and all the other boxes are for my powertools (from drill to impact wrench).
6:50 no it's wrong. you can't just connect the chain instead of replacing the dead LED element. This is a common mistake in all such video tutorials. Because it will increase the brightens due to raising of load to other LEDs, making them suffer more and very soon one or more will be dead too.
Hello! thanks for your comment. Wish you all the best!
Начинает видео с застрявшей вилки, которую видели ещё в 2018 году. Ну не бывает такого, чтобы вилка случайно попала в такое узкое место.
Thank you for watching
Superbes idées 👍👍
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
영상잘보고 갑니다
한국어로 알려주시면
더 인기가 많으실텐데요
Korean language subtitles are available, please turn on your language subtitles
The first one only works because they removed the wire opposite the way they put it on. If the pipe had installed over a straight wire this would not have worked.
電線不要纏繞會產生電感效應，固定電線要用壓接端子
Hello! thanks for your comment. Wish you all the best!
De l'Algérie 👌👌👍🇩🇿
Welcome to Creation Holic channel! Hope you have a good time while watching the video!
2,3,6,9번은 유지보수 기술로 좋은 팁.
Glad you like them!
ماشاءالله،عالی بود، آفرین
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Спасибо
Welcome to Creation Holic channel! Thank you so much for your support
You can not join coax cable, for every joint you make there is a 3 dB loss on the cable.
Hello! thanks for your comment. Wish you all the best!
Bravo bravo.
"Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"
Мм... Обожаю. Провод, который надо показать, что плохо закреплëн выдернул с видимым услием, а те, которые, типа, норм, те так... Слегка потряс из стороны в сторону. Ну, показал, ну молодец... Нет, безусловно, чем больше площадь провода, которая придавливается, тем лучше он будет держаться, но показывать это так убого ещё постараться надо.
Thank you for watching
Он ещё и не правильно его посадил
very good ❤❤❤
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Uzun süre kullanmadığım Raks vantilatörümü açtığımda hıç dönmedi. Motoru söküp şaftı hem önden hem arkadan yağladım. Dönmeye başladı ancak ilk açılışta hızlı dönüp😅 sonra yavaş dönmeye başlıyor. Ne arızası olabilir.
You should reapply the lubricant a few more times
Thank you!
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Gostei do vídeo
"Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"
#4 why would you want the extra resistance?
it will be very useful if you haven't bought a new device yet
superb
"Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"
Số 1 có nguyên tắc là gì nhỉ?
Great idea
"Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"
Indonesia,west java,karawang,cikampek,cikampek timur, cijalu, kebon kembang,
Welcome to Creation Holic channel! Thank you so much for your support
Ótimo vídeo! Gostei demais do ritmo dado, geralmente são cortadas várias etapas do processo para deixar o vídeo mais rápido, mas o formato pelo qual optou me proibiu de assisti-lo em velocidade acelerada o que ajudou e muito na absorção das dicas. Também gostei dos textos inseridos ao longo do vídeo. Parabéns pela coragem de fazer diferente!!!
Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!
Bei der Aktion mit den 2 Adern in dem Stecker, da gehören Ader-Endhülsen über die Kupferadern!!!
Thank you for your comment. Wish you have a nice day!
Def not going to want to do the LED light fix, that increases the voltage drop across the rest of the LED's in the circuit, might overheat, or start a fire.
Thank you for sharing your feedback and expressing your perspective
on the first LED fix it works, i have fixed LEDs over my room and work table for like... 2 or 3 years already. But with a 2nd LED fix in a few months the bulb melts (tried it with an independant connection)
ofc the 1st fix must be made properly, 1 option is like in the video and a 2nd option can be using string wires (thin as hair) to secure the soldering iron
Just add a resistor
@@creationholic101Your fine, just make sure there is no bad noticeable side effects these are all nice.
Сколько раз так делал и ничего не случилось
❤ very useful ❤
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Very cool stuff thank u
Glad you like them!
Номер 6. Все и так закручивают провод вокруг болта. Никто прямой провод не соединяет.
Hello! thanks for your comment. Wish you all the best!
I'm from Indonesia
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Что за бред с карандашиком?
Ничего, что схема и фотодиод рассчитаны на 3V?
I have used it and find it quite good
#2 without ferrules is illegal in germany, for reasons
What are the reasons? 🤡🤡🤡🤡
Insufficient contact area of the cross-section, damage to the individual strands, risk of fire
Hello! thanks for your comment. Wish you all the best!
@@creationholic101 Please do not make videos about electrics as you do not have in-depth knowledge of imitating people and endangering their health and life. In Germany you would have received an injunction and paid a large fine.
Good luck
"Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"
👌 Good sir.
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
your tricks are amazing
Hello! thanks for your comment. Wish you all the best!
Good idea 👍👍
Love from India ❤️❤️
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Полезно. 👍
Hello! thanks for your comment. Wish you all the best!
Нет
0:37 Das ist wirklich meisterhaft, eine Litze ohne Endhülse verklemmen.
3:21 Ich weiß jetzt nicht, wieso der Hersteller zwei Batterien benutzt, wenn doch eine reicht. Wieso 3 Volt, wenn das Gerät mit 1.5 Volt auch funktioniert.
Thank you for sharing your feedback and expressing your perspective
Nice
Welcome to Creation Holic channel! Thank you so much for your support
Very good.🙏❤️🙏❤️🙏
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Don't play with electricity.
brilliant mate. Australia
Merci brø
Thank you! Cheers!
Да постоянно тески есть спать, смешно😂😂😂😂😂
Thanks so much for watching our video. Wish you all the best
❤
I am more likely to have proper wire strippers than nail clippers.
Hello! thanks for your comment. Wish you all the best!
Bro number 5 is straight up illegal and will potentially kill some one
Hello! thanks for your comment. Wish you all the best!
First wone belongs to the 7 wonders of the world
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
дякую
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
zu 2, auf die Aderenden gehören aber Aderendhülsen drauf. Das sollten Sie aber wissen.
Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!
Diese verwendeten Stecker gehören in den Müll!
Ok everyone this is not how you fix electrical issues
Please try and feel
Amazing ideas bro
Thanks a lot
Danke, Schwester
2:11-А почему изолента не синяя?!?
TOC issues... 😮😮
This guy lives with stone age peoples
I'm sorry to hear that the video didn't meet your expectations. I appreciate you bringing this to my attention
I didn't understand the use of#9
thanks you
Bro this is just five minute crafts but smarter
Thank you for watching
Зачем портить карандаш? Долго на 1 батарейке пульт не проработает, мощность его снизилась. Проще было помять старые батарейки или заменить одну старую, на одну новую. Если уж в магазин так не хочется идти.
The purpose of the video is to assist people in emergency situations who haven't been able to purchase new items
❤❤❤
🍀☘☘😘😘😘😚😚😚
Не хочу обидеть, но многие из вариантов можно сделать проще и лучше😅
Лучше начните снимать обучающие электронике видео, а не старые лайфхаки😅
I'm sorry to hear that the video didn't meet your expectations. I appreciate you bringing this to my attention
A quien le ha pasado el número 1????
Thank you for watching
чё за бред с пультом, во первых от 1.5в он скорее всего даже не заработает или будет очень слабый сигнал, а во вторых грифель не проводит ток
Лампочка с коротышом место диода проработает от силы неделю, потом сгорит ещё один диод, т.к. на все оставшиеся диоды будет подано больше тока
it works very well, try it and feel it
ये बलफ का होल्डर पसंद आया इसके बारे में कुछ कहें या वीडियो बनाए
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Clearly has never worked with cables and electricity
Thank you for sharing your feedback and expressing your perspective
@@creationholic101 aaawww
💜💜💜💜💜
🍀☘☘😘😘😘😚😚😚
Відео дуже корисне,але не зрозуміла операція з пляшкою.
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
quella del telecomanda non è vera
I tried it and found it very good
Nunber 8 is the greatest joke. New cable or the correct f connector😅😅 2.80€
Hello! thanks for your comment. Wish you all the best!
# 2👍
🍀☘☘😘😘😘😚😚😚
3:30 your edits aren't smooth😅
Hello! thanks for your comment. Wish you all the best!
So sick of these ragebait vids LMAO these are horrible ideas please nobody try these fire hazard ideas
I understand that you didn't find this idea helpful, and I appreciate you sharing your perspective
@@creationholic101 no problem man! Just doing my part in interacting so you get ahead in the algorithm. Controversy gets interactions, which gets recommendations, which gets views.
Best of luck in growing your channel
З лампочкой таке не проходить пару разів робив перегоряє все одно