Electric pennyboard (Homemade for 70€)
HTML-код
- Опубликовано: 19 окт 2024
- Electric pennyboard (Homemade for 70€)
Follow me here.. on RUclips or on instagram
CHRISTOPHER_MOIS
Motor - D2826-6 2200 kV - 13€ (Better get a bigger one)
ESC - 40A - 5€
Battery - 3 cell lipo 11.1 Volt - 11€
Pulley/Belt - GT2 ebay - 5€ (Better get HTD type)
Pennyboard replica - 15€
Radio - Simple gun runio from hobyking - 25€
Leave a comment or sent me some parts and lets build a legit one toghether..
Music by:
Kristián Gulik - Limited - Royalty Free Music
♫ Skladba je Royalty Free a je možné ju použiť vo svojich videách.
Do popisu videa musíte umiestniť tieto informácie:
Mate, you've got your motor mounted static and your trucks that can move! It won't be long before you turn and that belt comes right off! Also that motor is too high KV to pull a human, it will burn out in no time at all. You need something less than 300kv.
darkkevind1978 what would you say for an 800kv motor for a person who ways 87 pounds
What about 750 kV for someone who weight 70 kg
WAAAAYYY too high. The highest you would ever want for any weight is 270kv.
no way. Go for something under 250kv
Would the pulley be fine if the mount was attached to the trucks because wouldn’t the mount move with the trucks when you turn
If you take it to your mail box to get the mail does it run out of battery on the way back?
no.. but it will if you keep doing that for 15 min
you just got roasted McDonald
(Face palm) when you said boosted board you had a picture of an E-GO....
Martinpe I was looking for this comment
Gladl found it.
Why do you care?
Martinpe boosted board is not an electric skateboard brand
Efe Ütüklerli it is
This is very inspiring. I just might do this thank you
cool super cheap budget build, im curious how long that little motor is gonna hold up lol most of us in the DIY esk8 crowd use 63mm motor maybe 50mm
was about a good week.. you re right, i went cheap on the motor but my goal was to build it and gain experience
do you have any vibration problems? or problems with misalignment when going through corners?
Very cool video, thanks for sharing!
Will a transmitter with 3 ch work? And also can I use a motor with 900w power and 5800rpm? What is the spec of your motor? And is your motor fast and efficient? What did you do about waterproofing the motor and the electronics? Thanks!
Looks soo good !! can't wait for electric penny 2.0 maybe a moter that's more discreet, like quieter and something that is more powerful, cheers and good luck
This is great! I'm looking forward to seeing your new build. Are you going to post any teasers or snippets?
thanks.. maybe.. i am still waiting for my sponsor to provide me a longboard
Nice job! I am looking to build one like you. Does it still last untill now? I just worried about that ESC( it is not VESC) ? Thanks
whats Vesc.. unfortunatly it doesnt
finaly someone who says it.. those prices are ridiculous for those boards to buy
look if china can sell a hooverboard (2 wheel balancing board with segway kinda electronics in it) for 160 euros retail. why the fuq does a skateboard with a motor battery and voltagecontrol cost that much
guess the next skateboard project didnt happen. as i looked though your video list. shame as i would have loved to see a better but still reasonable priced board
very good brother wish you good luck......... :-)
great vid
Just got yourself a new subscriber my friend this is awesome I'll be sure to share the video
Is it posible to make it without programming the esc? Or you must do it to make it run?
If the ESC is already programmed you don't need to program it again.
With the motor mounted to the non-moving part of the truck (instead of to the cross bar), doesn't that twist the timing belt when you turn? Any issues with the timing belt slipping off during turns?
Great video!
Wich better motor you recommend?
Whered u get that board? Im looking for that color
Awesome video man!
Nice work dude...really like it.I also want to turn my penny board like that.Really like it men thumbs UP
from where did you get the motor and the pulley
Very cool bro.
what motor did you use in the new version?
How fast can it go?
Id really like to make an e-board with my nickel board the way you did the penny. I want to do it with a beefier motor/battery of course. I can use all the tips I can get. Especially the way you got the Pulley to work with the original wheel.
Can you also use the electronics of an old rc car? That you only have to change the battery And motor?
what I learned is you can just better battery And motor and you should be alright
Petty good I like it
like very good video
What charger did you use?
I like your style! Never give up! Maybe your final design will be better than the boosted board.
Where did you get your replica penny board?
will the 380kv motor work ???
Ωραίο βίντεο
the motor uses a 5-t pinion gear right? But i can't find one
So much inspiration!
I am with you when you said holy shit that's expensive
Love that voice
Hi, where did you buy everything?
What is the max speed?
Nice project!
I'm from Italy! Thanks.
And which motor is better? It's better a lower kv motor or what? Thanks.
lower kv is better more powerfull but not fast.. 240-400 kv is just a fine motor
Hello
Can you put the links für the Produkts in the discription?
Hey Crespo
Did you try the cheap 10 to 20$ penny board? I want to buy one but I'm confused about it
hi, yes i did.. well its not perfect and it doesnt roll smoothly.. if you planing to spent a life on it .. get the brand one
Ty bro
did you end up making another one? couldnt find the video on your channel
Not yet unfortunately.. couldn't get any sponsors :/
How did you put the wheel pulley on the wheel?
Awesome
Can I put there a receiver And remote from a remote controlled car?
What Motor should i buy? I want to build an electric board, too!
s 50-60 270kv would be great
V12
Hi!, Great project!!!
How do you fix the wheel pulley to the wheel?
thank you, its actually a belt (clsoe loop) that i put on a round plastick bit that i found around and then i nailed it to the wheel..
So, if you could start again what components would you like to change and which would be the new ones?
this time i am using a bigger pulley instead of a small close loop on a plasti piece.. i am searching for new motor and other components
i love the intro aha
Good Work
it is very nice
For some reason this video was super inspiring
"Never give up though, make some changes and try again"
- Crespo Greek
You should use a lower KV motor, a boosted board uses a 210KV motor (but works on 24v) with the reduction you have now and since you use a 3 cell you should get one around 600-800 KV (750KV is readily available)
Also, replace your bearings with skate bearings, it will make your board smoother and greatly increase battery performance. (I would say in your price range get Enuff ABEC 9's for about 10USD)
Can you also use the electronics of an old rc car? That you only have to change the battery And motor?
the old RC car may not have a brushless motor and this will make it hard-impossible to ride
I Will change the motor to a brushless motor And a bigger accu
Nikola Tesla do you think a 1000kv would work well for an 80lb kid
very inspiring
how do you put the gear on the skateboard wheel?
nailed the custom gear onto the wheel..
good job dude!
how long are your timing belts?
How fast could you make this while staying under $120
1mph your welcome
nice job
thank you
nice job it might not be that good but its nice
Hey man,
how did you mount the hub pulley?
Cheers
i found a round plastic piece.. i putted a closed loop belt on it.. and bolted it on the wheel.. simple small bolts
CRESPO GREEK didn't you use the timing pulley stuff you had in the video?
i did.. small pulley to the motor .. custome big one to the wheel .. if you mean the small one.. i drilled it to make a bigger diameter and just hummered it on to the motor
CRESPO GREEK Is the big one flat?
ahh.. it has teeth GT2 type
Dude ur rlly beast!!! U deserve more subs!!!👍👍👍
What about the receiver and the pulley?
Where do u buy all this
How many ampere has the battery?
can you link me the pulley?i never know such thing b4 lol
How did you attract the cog wheel on the motor? BTW Nice video.
ty.. i bolted it with small screws.. the wheel was easy to drill ..
+CRESPO GREEK but how did you attach the cog wheel on the motor shaft.
oh sorry.. i bought a pulley from ebay.. i disassembled it and kept only the ring with the teeth.. then i simple drilled the same size as the motor (outside) shaft and hummered it there..
+CRESPO GREEK thanks! One more question. Do you need a 180mm Paris truck with 83mm flywheels or the standard penny board truck works?
it doesnt matter.. you can make anything work
good video bro
How many km per hour was it
wonderful. i want to make a motorized suitcase something assist to moving a suitcase.
Great idea
What does 50c and 25c mean on the lipo battery's
And would you recommend a 2200kv or 1000kv motor
What size motor is that ? :)
so basically all I have to do is rip apart a remote control car lol
youre using an rc brushless motor rightn
Time ride with this battery?..
500W sensored motor and esc will do big difference in results and small in price.
And you could made diy BMS to protect that lipo from deep discharge, just atmega8 and mosfet will do it
you're everywhere :D how do you have so much knowledge on this subject?
Thanks bro.
I just learn it from internet, its my hobby.
You see me everywhere because both of us follow same subjects on youtube(eg. esk8s).
Polak Arek??
CASEY IS AWESOME
Next time you should fix the motor holder to the axis part because the base plate and the axis parts are move relative to each other. It means the belt can be lose or tight while turning left or right. I hope I could help.
what the name of your controller?
Μένεις Αμερική ;
so swag
When is the second part I love this video it's awesome. I got the same motor 2200kv I'm also gonna try a 1000kv even tho these boards should really have like a 180kv motor. I do weigh only 83 pounds so this should work to like maybe a 8 mph
Building&Filming is It working?
I was thinking about doing this but adding a motor to the two front wheels and covering the parts to keep it water proof
sounds like a complete work.. that was my plan too but soon you realize that you just wonna Go..
The price of that would be 😬
You cant use a 2200KV motor on a E-board...
For 70 bucks you can make your very own earrape board
what is the name of your transmitter
Are you by any chance Dutch?
where you buy pennyboard
Like goto a vans or tillys
Cant you share with me the project 3d? I'm tryng modeling with fusion 360 but not sucess xP
I don't think i can find the files after all this time, i did it with solidworks, demonstration reasons only
what are the 5th and 6th material's called
You should buy a bigger low kV motor and move the axis. So you've got the spinning part of the motor, then the part with the cable's, then the bracket and the the belt.
is it a 22" or 27" penny¿?
its a replica, i bieleve of the 27'' one
CRESPO GREEK thanks
+Angelvirus 22"
its a 22", you can tell by looking at it
I wish I had the stuff to do this
ebay is the solution
me to
+DAT BOI he's like 5
money?
its just my clean shave
how you put the pulley on the wheel?
try putting pulleys on both sides of the back trucks
thats not an original Penny Board
Can this please go hella viral?!?!
The reason your belt fell off is probably because you mounted the motor to the base of the trucks between the trucks and the board. So when you turned the gear on the wheel would get disalined with the motor. I would recommend that you make the motor fixed to the cylindrical part of the truck near the wheel. You can get what i mean if you google electric longboard motor mount. Of course this is only if the belt falling off problem perists
What is the cost in US currency?
Ορεο
wont be long before you burn that little motor btw this is 2 yrs ago so what happened?