Thank you to everyone for watching, commenting and giving my videos a thumbs up. Please like and share this video where ever you can it really helps to get my videos noticed. If you have any questions or ideas of what you want to share please leave a comment. Thank you to each and every one of you! Ken
Thanks for the advice. I am new to turning and have been adding to my accessories as I can afford. The purchase of chuck has been on hold due to concision on what to buy. You have been very helpful.
Thanks Jim. I have another video on my opinion for lathe tools too. Here it is if you would like to check it out. ruclips.net/video/BrbvA8P32IE/видео.html
I started with a Nova G3 about three years ago, It has done me well and I still use it most every week. I do have a suggestion, it may be only with mine, it might be with all, but, when I take a piece out of the Nova G3 and set it aside, when I come back to turn it, it does not resister as I would expect. I ran a dial indicator on the chuck and found out that it registers about 30 to 35 thousands out of round. This is not a problem if you do not take your piece out of the chuck, or if you remove the piece and still have a large margin to turn, but if you use the G3 and want it to index extremely close to the original position, I would suggest putting a sharpie mark in between two of the jaws,, and also putting a sharpie mark on the base of the chuck , aligning with those marks, on the tendon, so that I can put the piece back exactly where it was originally chucked. With mine, it seems that the adapter, the way that it screws to the mandrel, and also screws to the chuck, is where the inconsistency is, I can remove the chuck from the lathe, and reinstall it, it is always a bit off, running true, but it always off at the same spot. Using register marks that I mentioned with the sharpie will eliminate this. I recently purchased a OneWay Stronghold chuck, that has an adapter that screws onto the lathe mandrel, and slip fits into the back of the Stronghold chuck. With a dial indicator, it still runs out a couple of thousands, but the set up is more accurate. I still do indexing marks on the OneWay chuck, though it probably is not necessary, it is just something I learned from using the Nova G3. If you are getting close to the final cut, and have to remove the piece, whatever chuck you use, the indexing marks with the sharpie will make you more accurate. if you do not remove the piece, then you don't have a problem. You will never see 30 thousands looking at the bottom of a turning. This might not be a problem for most turners, but I hate to be turning a 12" bowl, with 1/4" walls, have to remove it to do something pressing, and find flat spots after the finished cut. Again, if you do not remove the piece, you should not have a problem. I like Nova products.. WH
Marking the piece and the chuck is fantastic advice. I usually keep the chuck attached to the piece throughout, but there are times I need to take it out. You really can't see it but I have a permanent marker mark on my G3 for just suck and issue. I'm glad you brought it up since I failed to talk about it in the video. Thank you. Ken
Thank you. I am replacing my 1 x 8 lathe with a 1.25 x 8 and I didn't realize I could get an adapter. Still going with a stronghold chuck on the new lathe but now I can keep my old chucks for other uses.
I only have one chuck and it's the G3. I eventually want to buy more because I hate changing the jaws. One thing I love is the flexible drive center that clamps in the jaws. It allows you to turn between centers until you make a tenon without having to take the chuck off the lathe. Go get one and thank me later.
I insert my drive spur in the chuck and use the tail stock sometimes. super easy and no need to put on face plate. flexible drive center? Never heard of it. Ken
@@MoonpieCreations It's pretty much just a drive spur but the center point is spring loaded so it makes mounting a little easier. www.amazon.com/9021-Flexible-Point-Drive-Center/dp/B01BHJF7P0/ref=sr_1_1?keywords=flexible+drive+spur&qid=1557412696&s=gateway&sr=8-1
@@MoonpieCreations I don't use mine as much. It has a speed limit of like 700 rpm I think. Used it maybe twice and had them for over 2 years I think. Maybe as I progress. Anyway still a good intro to chucks and review on the nova chucks
Been planning on buying a Nova G3 chuck for years... but I'm disappointed that their new production chucks are now made with Copper Composite jaw slides, instead of steel. Explains why a lot of reviews on the new chuck complain about the jaw slides wearing out.
@@MoonpieCreations I read it in the description on the Woodcraft website, for the G3 chucks. Cooper composite jaw slides are actually listed as a "feature". Not sure how jaw slides made of a soft metal can be a a feature.
Hey Phil, I get them off Amazon. Here is a link to the large round cutters amzn.to/3PT8rgt Here are the detail cutters: amzn.to/3vJ1KXo Here are the square cutters with a slight radius: amzn.to/3UhbDVT
Dude! You are KILLING me rofl. I might suggest reading a script, at least for dimensions next time ;-) In all honestly, you obviously have forgotten more about chuck's (How much wood, wood a woodchuck chuck.....) than 99% of us will ever know. I give you huge credit for being able to laugh at yourself. A true sign that you are very secure about your knowledge. I do LOTS of woodworking...but, I haven't operated a lathe, wood or metal, in probably 30 years. About to purchase a JET 1221, so this was an incredibly insightful video. MUCH Thanks, and I will certainly subscribe to your content. ALSO, for some of your viewers, TPI= Teeth Per Inch or "Pitch" of thread ;-) ALSO, ALSO, have you thought about taking a piece of tubing and slot the end for your Pinion Key? Would definitely save your thumb some duress.. Cheers
I'm planning to buy as a gift a wood lathe workship with all the tools and you video is really helpful. Thank you. What about chisels? As a beginner , which one of them do you recommend? Or should I buy the whole set. :)
Hey my brother I have a Question for you ok,I have a Delta Iron bed 1440 lathe, What Chuck I need for it?,And i have a Shop Fax Mini lathe what chuck this one needs ok,If you can help me my brother I will appreciated Thank You and take care later :)
TJ, I've looked both of these up and can't find the TPI. I will keep looking and if I find it I will let you know. Once you find the TPI you can find an insert that fits for the G3 Ken
Ron, different lathes have different threads. But I don't think any are better than the other. I have a 1 1/4" 8tpi. others are 3/4" 16TPi. and a bunch of other combinations. Your lathe manual should have the TPI you need for your spindle. I hope this is what you were talking about. Ken
I have a tekatool nova scroll chuck I inherited and it’s frozen! Can’t open and close the jaws very well. I don’t think the owner ever cleaned it. How do I remove the scroll ring?
This video will show you how to take your chuck apart. I hope it works for you. I had to use this video when I got resin inside my truck jars and couldn’t open or close it. ruclips.net/video/DMeL8pQFFFs/видео.html
@@MoonpieCreations mine does not have that black cover on it. You see the scroll ring underneath plus that snap ring. If I get the snap ring off can I then access the scroll ring to get it off? I think it bound with saw dust. I tried blowing it out, took 50 mm jaws off and cleaned those. I had seen that video before.
Hmmm, not sure why it says that. I turn up to 12" diameter bowls using a tenon. It all depends which jaws you use. They do not recommend using the larger 130mm jaws, but are okay with the 100mm jaws. The 100m jaws are okay for up to 14" diameter and 5" deep. They are most likely speaking of the spigot jaws. No matter what I say, please side with what you feel safe doing.
Thank you to everyone for watching, commenting and giving my videos a thumbs up. Please like and share this video where ever you can it really helps to get my videos noticed. If you have any questions or ideas of what you want to share please leave a comment. Thank you to each and every one of you!
Ken
Ken - thanks for the info and reply
It’s highly recommended when using the cole jaws, to also use your tail stock. As the end of your video points out. Great video, thanks for sharing
Great tip!
Thanks for the advice. I am new to turning and have been adding to my accessories as I can afford. The purchase of chuck has been on hold due to concision on what to buy. You have been very helpful.
Thanks Jim. I have another video on my opinion for lathe tools too. Here it is if you would like to check it out. ruclips.net/video/BrbvA8P32IE/видео.html
From a beginner, thanks Ken for that chuck explanation!
Gary
You are welcome. I hope it helps a bit.
Ken
I started with a Nova G3 about three years ago, It has done me well and I still use it most every week. I do have a suggestion, it may be only with mine, it might be with all, but, when I take a piece out of the Nova G3 and set it aside, when I come back to turn it, it does not resister as I would expect. I ran a dial indicator on the chuck and found out that it registers about 30 to 35 thousands out of round. This is not a problem if you do not take your piece out of the chuck, or if you remove the piece and still have a large margin to turn, but if you use the G3 and want it to index extremely close to the original position, I would suggest putting a sharpie mark in between two of the jaws,, and also putting a sharpie mark on the base of the chuck , aligning with those marks, on the tendon, so that I can put the piece back exactly where it was originally chucked. With mine, it seems that the adapter, the way that it screws to the mandrel, and also screws to the chuck, is where the inconsistency is, I can remove the chuck from the lathe, and reinstall it, it is always a bit off, running true, but it always off at the same spot. Using register marks that I mentioned with the sharpie will eliminate this.
I recently purchased a OneWay Stronghold chuck, that has an adapter that screws onto the lathe mandrel, and slip fits into the back of the Stronghold chuck. With a dial indicator, it still runs out a couple of thousands, but the set up is more accurate.
I still do indexing marks on the OneWay chuck, though it probably is not necessary, it is just something I learned from using the Nova G3.
If you are getting close to the final cut, and have to remove the piece, whatever chuck you use, the indexing marks with the sharpie will make you more accurate. if you do not remove the piece, then you don't have a problem. You will never see 30 thousands looking at the bottom of a turning.
This might not be a problem for most turners, but I hate to be turning a 12" bowl, with 1/4" walls, have to remove it to do something pressing, and find flat spots after the finished cut.
Again, if you do not remove the piece, you should not have a problem.
I like Nova products..
WH
Marking the piece and the chuck is fantastic advice. I usually keep the chuck attached to the piece throughout, but there are times I need to take it out. You really can't see it but I have a permanent marker mark on my G3 for just suck and issue. I'm glad you brought it up since I failed to talk about it in the video. Thank you.
Ken
Thank you. I am replacing my 1 x 8 lathe with a 1.25 x 8 and I didn't realize I could get an adapter. Still going with a stronghold chuck on the new lathe but now I can keep my old chucks for other uses.
That is great to hear. I did the same for all my faceplates also.
Ken
I only have one chuck and it's the G3. I eventually want to buy more because I hate changing the jaws. One thing I love is the flexible drive center that clamps in the jaws. It allows you to turn between centers until you make a tenon without having to take the chuck off the lathe. Go get one and thank me later.
I insert my drive spur in the chuck and use the tail stock sometimes. super easy and no need to put on face plate. flexible drive center? Never heard of it.
Ken
@@MoonpieCreations It's pretty much just a drive spur but the center point is spring loaded so it makes mounting a little easier. www.amazon.com/9021-Flexible-Point-Drive-Center/dp/B01BHJF7P0/ref=sr_1_1?keywords=flexible+drive+spur&qid=1557412696&s=gateway&sr=8-1
I bought a Wen turning chuck and boy do I wish I had watched your video first.
appreciate the video... adding a lathe to my studio and had questions on chucks, this video helped out.... thanks
Glad it helped.
You talked about Jaws, and chucks, but you didn’t answer the life long question of how much wood could a wood chuck chuck! Lol! Great video Ken
Bahahahahaha, nicely done my friend, nicely done.
Ken
Very funny!
Really appreciate you posting this video.
Glad it was helpful!
Really enjoyed your humor! It was Great. I was really expecting you to say: ( how much wood could a wood chuck chuck? ) at some point. :-)
Hahahhahahahhaha, Thanks for watching.
Let’s talk about Chucks 00:03 😂
I like this guys sense of humour 👍
Thank you. 😜
Ken
i got the g3 its a great chuck . i love it alot . it sure made turning alot easier .
I love the G3, but I have started turning larger bowl so I have to use the supernove 2 more often.
Ken
Nice review. I have 2 of the Record power chucks (one larger one one smaller one). I need a 3rd for my cole jaws.
It’s great having on permanently on my cole jaws.
@@MoonpieCreations I don't use mine as much. It has a speed limit of like 700 rpm I think. Used it maybe twice and had them for over 2 years I think. Maybe as I progress. Anyway still a good intro to chucks and review on the nova chucks
Great info. I learned a lot. You got many of your dimensions wrong though, so I’d work on that for future content.
Thanks I'll look it over.
Been planning on buying a Nova G3 chuck for years... but I'm disappointed that their new production chucks are now made with Copper Composite jaw slides, instead of steel.
Explains why a lot of reviews on the new chuck complain about the jaw slides wearing out.
I hadn't heard that. hmmmm thanks for the info I will look it up.
@@MoonpieCreations
I read it in the description on the Woodcraft website, for the G3 chucks. Cooper composite jaw slides are actually listed as a "feature".
Not sure how jaw slides made of a soft metal can be a a feature.
Ken at 5:17 you show some cutting tools (carbide cutters) can you send a link?
Hey Phil, I get them off Amazon. Here is a link to the large round cutters amzn.to/3PT8rgt
Here are the detail cutters: amzn.to/3vJ1KXo
Here are the square cutters with a slight radius: amzn.to/3UhbDVT
I also use Novas. I wish the smaller jaws, 50/70mm is that the tenon/inside of the jaws is not dove tail. And, I really prefer dove tails.
I'm with you on that. I have started using the 100mm more often.
Ken
@@MoonpieCreations I actually avoid using he smaller jaws with tenons. See ya, Larry
Thank you very much.
You are welcome!
Dude! You are KILLING me rofl.
I might suggest reading a script, at least for dimensions next time ;-)
In all honestly, you obviously have forgotten more about chuck's (How much wood, wood a woodchuck chuck.....) than 99% of us will ever know.
I give you huge credit for being able to laugh at yourself. A true sign that you are very secure about your knowledge.
I do LOTS of woodworking...but, I haven't operated a lathe, wood or metal, in probably 30 years. About to purchase a JET 1221, so this was an incredibly insightful video.
MUCH Thanks, and I will certainly subscribe to your content.
ALSO, for some of your viewers, TPI= Teeth Per Inch or "Pitch" of thread ;-)
ALSO, ALSO, have you thought about taking a piece of tubing and slot the end for your Pinion Key? Would definitely save your thumb some duress..
Cheers
Thank you for the information what about the Nova Infinity quick change chuck?
Don Lyons oh man that’s a good one. Although very costly. I am saving for one now.
@@MoonpieCreations I have one for a year now and love it
I'm planning to buy as a gift a wood lathe workship with all the tools and you video is really helpful. Thank you. What about chisels? As a beginner , which one of them do you recommend? Or should I buy the whole set. :)
I'm glad I could be helpful. I talk about lathe tools in this video ruclips.net/video/BrbvA8P32IE/видео.html. I hope it is helpful. Good luck.
Ken
Thank you a lot. I appreciate it. My dad would love this gift. Who wouldn't? Haha.
All the best!😊😁
Awesome informational educational video experience Y'alls
Thank you Sir.
Ken
Good info Ken, I did buy the G3, but haven't used it yet, but it's coming
Did you buy one that needed an insert or one made for your lathe?
Ken
@@MoonpieCreations I bought a adapter too
Hey my brother I have a Question for you ok,I have a Delta Iron bed 1440 lathe, What Chuck I need for it?,And i have a Shop Fax Mini lathe what chuck this one needs ok,If you can help me my brother I will appreciated Thank You and take care later :)
TJ,
I've looked both of these up and can't find the TPI. I will keep looking and if I find it I will let you know. Once you find the TPI you can find an insert that fits for the G3
Ken
I have the same lathe. 1" by 8
An informative video thanks. As far as lathes go is there a better/best thread size to get regarding strength, etc?
Thanks in advance.
Ron
Ron, different lathes have different threads. But I don't think any are better than the other. I have a 1 1/4" 8tpi. others are 3/4" 16TPi. and a bunch of other combinations. Your lathe manual should have the TPI you need for your spindle. I hope this is what you were talking about.
Ken
Thank you for your insight it’s helping me a great deal
No problem, let me know if you have any questions
Ken
I have a tekatool nova scroll chuck I inherited and it’s frozen! Can’t open and close the jaws very well. I don’t think the owner ever cleaned it. How do I remove the scroll ring?
This video will show you how to take your chuck apart. I hope it works for you. I had to use this video when I got resin inside my truck jars and couldn’t open or close it. ruclips.net/video/DMeL8pQFFFs/видео.html
@@MoonpieCreations mine does not have that black cover on it. You see the scroll ring underneath plus that snap ring. If I get the snap ring off can I then access the scroll ring to get it off? I think it bound with saw dust. I tried blowing it out, took 50 mm jaws off and cleaned those. I had seen that video before.
@@kandiecandelaria1423 I want to get the snap ring off it should come out easily.
if you have a pinion gear this would normally drive a crown wheel (automotive transmission speak) gearbox building, those were the days
That is interesting. I had to look crown wheel up and yes that is exactly what it is. Thank you.
Ken
@@MoonpieCreations I am a fountain of useless information so I've been told, I'm glad I could pass some of it on
My G3 manual says you can only turn a 4 inch blank that’s 6 inches long using a tenon. Am I correct?
Hmmm, not sure why it says that. I turn up to 12" diameter bowls using a tenon. It all depends which jaws you use. They do not recommend using the larger 130mm jaws, but are okay with the 100mm jaws. The 100m jaws are okay for up to 14" diameter and 5" deep. They are most likely speaking of the spigot jaws. No matter what I say, please side with what you feel safe doing.
Thank you for your response. I guess I will be buying the 100 mm jaws. Great video. 👍
BTW, your TPI is not "1 1/4" 8 TPI". TPI stands for (T)hreads (P)er (I)nch, therefore your TPI would be 8.
Nalgas Heladas ya but my spindle is 1 1/4” and that needs to be said as not all are.
Ken
💯😎👍👍
Thanks OG!!!!
Ken
The sniffing turned me away from this vid.
SparkeyDogfish I take it you mean sniffling. I had a cold, so sorry.
Ken