3 Ways Mount Wood To Lathe - Bowl Woodturning Video
HTML-код
- Опубликовано: 6 ноя 2020
- 3 Ways Mount Wood To Lathe - Bowl Woodturning Video
Attaching a wood blank to the lathe is one of the first skills that must be learned and mastered. When turning wood bowls, it is especially important to understand which methods work best for each type of bowl blanks.
In this video, I'll cover three different ways to mount a bowl blank to the lathe. I'll share with you my favorites and we will go over the advantages and disadvantages of each method for mounting wood to a lathe.
Check out these other relevant videos:
• Making a Tenon - • Turning A Perfect Teno...
• Twice Turning - • Woodturning Twice Turn...
• Tenon Removal - • Wood Bowl Tenon Base R...
______________________________
********** TOOL SHARPENING eCOURSE for WOOD BOWL TURNING
turnawoodbowl.com/courses/too...
______________________________
EQUIPMENT USED
Live Center (with bearings on tailstock) - amzn.to/3gZxn1K
Tailstock Extension - amzn.to/30YGIjX
4 Spur Drive Center (MT2 Morse Taper) - amzn.to/3gtha4i
1-1/4" x 8 TPI Faceplate - amzn.to/3ofTdTi
1" x 8 TPI Faceplate - amzn.to/2IL2xOy
3/4" x 16 TPI Faceplate - amzn.to/35lVRy3
1-1/4" x 8 TPI - Four Jaw Dovetail Chuck (w/ screw option) - amzn.to/3m6jEJd
1" x 8 TPI - Four Jaw Dovetail Chuck (w/ screw option) - amzn.to/2Hp5JPJ
3/4" x 16 TPI - Four Jaw Dovetail Chuck (w/ screw option) - amzn.to/35oLJET
M33 x 3.5mm - Four Jaw Dovetail Chuck (w/ screw option) - amzn.to/3m9S9yu
Cordless Impact Drill Driver - amzn.to/3jjMPGS
_____________
If you are curious about, or already completely addicted to turning wood bowls, check out my website dedicated to the art and craft of turning wood bowls!
www.TurnAWoodBowl.com
____________________
Turn A Wood Bowl is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com.
_____________________________________________________________
Online Turning Courses --- turnawoodbowl.com/courses/
Website --- turnawoodbowl.com/
My Publications --- turnawoodbowl.com/shop/
RUclips --- turnawoodbowl.com/RUclips
Instagram --- turnawoodbowl.com/Instagram
Etsy Shop --- www.etsy.com/shop/RelivedWood
Pinterest --- turnawoodbowl.com/Pinterest
Facebook --- turnawoodbowl.com/FaceBook
_____________________________________________________________
FREE WOOD BOWL TURNING TIPS EMAILED EACH WEEK - Sign Up Free
turnawoodbowl.com/tips
_____________________________________________________________
*** TOOL SHARPENING FOR WOOD BOWL TURNING - ONLINE COURSE
turnawoodbowl.com/tool-sharpe...
_____________________________________________________________
*** WOOD BOWL TURNING Start-to-Finish - ONLINE COURSE
turnawoodbowl.com/courses/woo...
_____________________________________________________________
#woodturning
#woodworking
#turnawoodbowl 
Хобби
Thanks for your time to put these videos out. To a brand new turner they are invaluable. I have only used the jaw chuck and 4 spur method so far. Great information great teacher.
I am a beginner Woodturner so my obvious choice is the faceplate for security reasons.
Richard, that's a great way to start. Welcome and enjoy the process. All the best to you and Happy Turning!
I've watched other instructors videos and came away wanting. This was not the case with this one. Very clear and concise instructions. Thank you.
Glad it was helpful! Happy Turning!
Thanks for all the nice and clear info, I use all three but prefer a base plate... cheers
Right on! Happy Turning!
Richard Raffin seems to use the screw chuck most often but I’m not sure if that’s just what I’ve seen or if it’s his preference. He actually also shows how to place it on there when it’s spinning and talks about how to slow the speed and to handle it carefully. Of course he’s been doing it for decades lol. I’d be nervous to do it starting out.
Yes, remember Richard uses techniques for high volume production. There’s nothing wrong with that but that is where his techniques originate. Happy Turning!
Thanks Kent, you’ve completely answered my question as I’m trying to turn a plate and haven’t worked a lather for 30 years. Appreciate your help
First, thank you for your incredibly clear videos! I have never had any luck with the worm and generally use the end to end method. I like this because it is easy to turn the bowl around and keep the same balance. I also generally turn small items and this is just quicker and I don't have to worry about running into a screw! (I now use the face plate on the inside of the bowl, turn the tenon on the bottom and then reverse and use the four jaw chuck. The way I was taught was to use the face plate on a glued on tenon and then turn that off at the end. I never, well almost never, do that anymore. ) But, I found this video really instructive and you answered a lot of my concerns!
Excellent, I'm glad this video was beneficial to you. Thanks and Happy Turning!
Excellent exposition, thank you, Kent. It’s the details that matter and you cover them brilliantly! You’re making lock-down (here in the UK) more than bearable - can’t tell you how grateful I am. Best Hugh
Hugh,
Wow, thanks. I appreciate you and your kind words. All the best to you! Check out my new online eCourse turnawoodbowl.com/wood-bowl-turning-start-to-finish-online-ecourse/
Happy Turning,
Kent
As always, thanks for the tuition and refresher that we all so need. I use all three methods, the choice is usually made for me by the piece - size, weight, balance and how round it is. I also slightly counter sink the four spur to provide a "protective" shroud to reduce fly-off possibility should I do something to dislodge the piece. Your methodology and coaching techniques result in keeping me, and I am sure all of us who watch your videos, focused. You polish up what I pick up by watching so many of the other amazing folk who share their wood-turning with us. Take care, keep well and keep the coaching videos coming.
Thank you so very much. I appreciate you! Happy Turning!
Here is a thought, Kent. Something a lot of us struggle with is getting the profile of the grind on our gouges correct. You have covered the different types of grind extremely well, but we often get the tip to edge profile wrong. I use a Tormek system and in theory it is fail safe. At least I initially thought so, until I kept finding I could not keep on the bevel with the tip of my gouge. I then realised the cutting edge of my sweptback gouge was becoming curved down to the tip resulting in my losing the bevel and the tool becoming dull very quickly. Maybe this is something you could guide us on, the errors turners often make with the grind, in one of your tutorials.
I have not turned a bowl yet! I just got my lathe set up and came here to figure out what to do. Great tutorial thank you!
Happy turning
Thanks for sharing your knowledge Kent. I’ve been turning for about 6 months and have learned so much from your clear and concise videos. I signed up for your sharpening course and have found the information invaluable. The sharpening course has taken all of the mystery out of how to properly sharpen all of my turning tools. I purchase the Wolverine sharpening system, and am confident in how to use it properly. My very sharp tools are making turning easier and more enjoyable! Thx again, and keep up the great work.
Thank you so much for sharing your experience! That's the whole goal of the Tool Sharpening eCourse, to provide you with the information needed to be confident making sharp tools. I'm so happy for you because this one step is the difference between a pleasant or difficult turning experience. All the best to you! Happy Turning!
Absolutely fantastic video my friend it has been about 20 years since my last wood turning but I am wanting to get back into it and this video is fantastic for trying to remember tips and also learning a new skill.
A master teacher. I have progressed so far in turning by watching your videos and reading books. Thank you for your dedication and links to products.
You are very welcome Happy Turning!
Thank you for such clear and great explanation. I’m getting a Nova Comet II and looking forward to starting my new journey and I really appreciate the way you explain everything
Very welcome! All the best to you and Happy Turning!
Hello Kent, I’ve been watching some of your videos and put in action what I’ve picked up and I thank you for all you do and give to all woodturning fellows. I use the screw warm as my first option mostly because I use a mortise rather than a tenon, I can remove the tailstock and refine the dovetail, second option is end to end and it depends on the size of the project, anything larger than 8 inches I’ll use screw warm. Cheers!!
Thanks for sharing. That's a good point. You can quickly switch between the worm screw and the chuck! Thanks and Happy Turning!
More great information, thank you! Just got my first jaw chuck. I know what it's like to start with a face plate. PLEASE, keep the great advice coming!
Will do! Happy Turning!
Good afternoon. A pleasure to find your video, I recently acquired a chuck very similar to yours and I had the problem of how to use the spike, although we do not share a language, the use of this accessory is clearly seen in your video, thank you very much for your excellent contribution, new follower
Glad it helped, Adolf. All the best to you and Happy Turning!
I got a mini wood lathe late summer and messed with it alot when I first got it and stopped but recently started with it again cause of the weather and the last few days I've wasted a lot of your videos and have learned so much. I was just kinda winging it till the last few days.
Thank you professor Kent!!!
Your videos are great for beginners as well as seasoned turners. I always learn from your videos.
Awesome! Thanks and Happy Turning!
Update, I am working on coring 12 walnut pieces about 16 inch in diameter. I put a face plate on one today and remembered what you said about making the grain even on both sides. Well, off came the face Plate and put it between centers. And what do you know??? It came out perfectly balanced. First time for such a heavy piece between centers. I’m hooked!!!
Thanks for sharing your knowledge.
Great video and I am a new turner with no mentor-so you are the mentor! Thank you!
Welcome! And I'm happy to have you under my wing. Happy Turning!
I trust the faceplate most. Mine is 3" with only 4 screws. Going to add additional sizes looking for 8 screw models. I also use the spur chuc, on small stuff, but my tail stock creeps. I think I can fix that by tightening the nut under the rails.
Kent, I just pure love your videos for the excellent way you explain everything so even a novice like me can easily grasp the information and turn it into action. You are hands down the best instructor. I've probably watched 50% of your videos, some more than once.
Can't say enough about how much you have taught me. Sharpening is still my biggest foe.
Thank you.
Howard Wittwer, Lyndoch , down under, Another great lesson that re-inforces what I have been doing. Your approach to instruction is first rate. I have noted your comment about moving the tail stock centre when using the spur to make the live edges even.
Excellent Happy Turning!
Thank you for your clear, straight talking videos. I am new to woodturning and find your videos are the best to help me understand each process along the way.
Thank you, Jane. I'm so glad to help. Happy Turning!
Thank you for these explanations. I'm new at woodturning, so I'm starting from scratch and I found your video really instructive.
Thanks for your very informative videos. They fit the newbie as well as the well experienced.
I use all three methods of mounting. Depending on the wood, size of blank, moisture of the blank and balance. Also I use a little candle wax on the screw and it's a little easier to get the blank unscrewed.
Take care, WyoGrizz
Thank you. And great tip for the screw chuck. All the best to you. Happy Turning!
Thanks for the informative and clear lessons. I have used all three methods, and similar to you I use the screw chuck the least. In a red oak live edge bowl that I am turning now I noticed the spur really gets sunk a lot into the wood as I turn the outside of the bowl. So just as you mentioned the tail stock needs constant monitoring, keep up the great work.
Thank you for writing and sharing! Great minds! ;) All the best to you and Happy Turning!
I also learned using the Faceplate. The shop probably uses this method for the newbies for safety. Your videos are explaining the why's to me and I appreciate the detailed descriptions. Learning in a community woodshop, I get many suggestions which may be conflicting.
LOL. I know what you mean. Raising babies, managing horses, and woodturning…everyone has an opinion and there are usually never two the same. ;) Happy Turning!
This is the best turning instruction that I have found on YT. Thanks very much!
I use mainly screw chucks because of the security issues. I find you videos very informative because you the pros and cons of the way you perform. Thank you.
Thanks and Happy Turning!
All of your description makes perfect sense.
I use the 4 sperre chuck and the tail stock to 95%. To make the connection safer I predrill the hole, where the center is connected, with a center drill. This gives me a much better connection because the fibers are removed and not just compressed. The center drill is used quite often on metal turning machines.
Great tip! Happy Turning!
I use all three, but I use the screw chuck and face plate more than the four spur chuck. I usually use that for spindle turning. Just the way I have taught myself. Thanks for the video. I always learn something.
Great, thanks for sharing and Happy Turning!
I prefer the face plate for security of larger blanks although I have little experience, but I’m learning thanks to you, Kent.
Right on Ron. The faceplate is great, especially when first starting out. All the best to you and Happy Turning!
Very good info. I like the fact that you are very thoroughly covering all options. Retired tool maker of 47 years. There is no set way of teaching. But good solid advice is a great place to start. Self reliance can be a long term relationship. Having someone to take the time to offer good advice can be the difference between a day or a bad day. Keep up the good work and thanks. From Ohio. WALTER
Thanks for watching Walter! All the best to you and Happy Turning! Kent
Thanks for another informative video. I started out using the face plate method. That was how I was taught. I have since started using the woodworm screw in an Oneway chuck. It seems to depend on the blank shape and size.
I like it. Happy Turning!
i appreciate your open, non-dogmatic approach to turning. you don't try to preach only one way to do things, ie, your way. you are, however, dogmatic relative to safety and that is appreciated. i share my lathe and shop with a few other people, so i like using faceplates so i can take my piece off the lathe if i am not done and let others use the machine. That is not the case with the 4 spur and the woodworm screw.
Ah, very good point you bring up. The ease and accuracy of removing and returning a blank to the lathe. You're right, the spur chuck would be the least forgiving to remove and return a blank. Some truing up would need to be done. And thanks for the non-dogmatic compliments. Ha! Thanks and Happy Turning!
i am learning.... every time.... thank you kent
Glad to hear it Thanks and Happy Turning!
I always use the spur chuck to start off with it's so easy to realign I try the screw chuck and the faceplate from time to time but I can never get them right so the spur chuck is best for me thank you for your videos I've learned a lot safe and happy turning to you
Thank you so much! Happy Turning!
Kent you make some of the best videos on RUclips you explain clearly well filmed for a beginner i find them very informative thanks.
Thanks 👍 Happy Turning!
Every Second…of watching your…tutorial…was priceless…
Thankyou So Much…for Sharing your Experirnce. I don’t even have a Lathe yet…so, I wanted some background knowledge - before I search for a quality lathe (preferably used) one due to prices - these days.
Thankyou again,Sir
Joseph
Hi, love your videos, clear and to the point, I have just started turning, absolutely love it, and I have seen a few videos on RUclips, but have to say I fine yours so easy to watch. I have learned a lot from you. Thank you.
Awesome, thank you! Happy Turning!
most of the times that I have had access to a lathe, I had face plates and 4 spur chucks, My son and I just this week bought a lathe ( the first either of us have actually owned) and it came with both the spur, and the face plate, but I ordered a 4 jaw chuck, and we are really excited about the ability to use tenons to make turning the inside of bowls and pots. thank you for your videos, even though I have used a lathe quite a bit in my life, I still learn from you. I am by no means a master turner, but as an avid enthusiast, I am open to learning as much as I can from people like you, that are much more experienced than I am.
Hello and welcome! Happy Turning!
A well explained procedure for attaching Bowl Blanks. Very helpful for me. Thank you
Excellent. Thank you, John! All the best to you and Happy Turning!
Hello Kent, thanks for another great video. I use a dedicated screw chuck or a spur drive between centers.
Great thanks for sharing! Thanks and Happy Turning!
Hi Kent, I really enjoyed watching you describing the 3 ways securing the wood too the lathe. I've just started turning ( pensioners hobbiy, I use the tailstock version, as for me it seems secure and safe.I won't just yet take on doing a bowl, after more practice maybe. At the moment I'm getting too know the chisels. Would you recommend I get to know how to turn with the newish chisels (carbine end's.I believe where you can just replace the little cutting ends when worn ,I'm not in any hurry, but I believe one can shape your work piece quicker. Looking forward to seeing more of your videos 🎉Stay safe my friend 😊
Brilliant video. Thank you very much. Exactly what I needed to know.
Glad it was helpful! Happy Turning!
Excellent. Thank you. Helps me so much in preparing for my classes today.
Fantastic, Diana! Enjoy and Happy Turning!
Thanks for sharing your knowledge. Great to see you are using the red robby screws
Thank you, Chris. Happy Turning!
Great video really appreciate the time and effort you put in!
Glad you enjoyed it! Thank you and Happy Turning!
Well done, thank you.
Very nice video, Kent.
I start - and later finish - nearly every bowl between centers. The exceptions are very, very few. The ability to tip & tilt the bowl to balance the figure and/or the natural edge outweighs all other considerations for me. I can then turn a tenon for a chuck, or turn a flat area for a faceplate or glue block, and the tail center is no problem-o: I leave a little nub that either fits between the chuck jaws, or size it to center the faceplate.
With a bit of practice, and taking care to *never* trust the bark as a mounting spot (I chisel away the bark to dig into solid wood) turning between centers should present no additional risk. Start slow, and don’t increase the speed until it’s well balanced.
Kent Thank you for the wonderful presentation.
You are very welcome. All the best to you and Happy Turning!
I'm new to wood turning having just retired. And was lucky enough to find your video, Thank you very much, and very well done, No Blurb, No crutch words, and useful info all the way. Much appreciated.
Awesome, thank you! Welcome and Happy Turning!
Hello Kent,
i´m absolutly new in tourning wood, yesterday i bought me an old used and cheap wood lathe.
And after watching so many Vids of other People, i´m really glad that i found your Channel.
First time, that i learned so much so easy!
And thank god, you made this Video, i was close to buy me an expensive Screwchuck!
But now i will start with Spear Chuck and the Faceplate!
Thank you very much, you got a new fan!
Wonderful! Welcome aboard and enjoy the whole process! Happy Turning!
Thank you for a very well made and helpfull video ; i am a seasoned woodworker, but relatively new bowl crafter. I use the faceplate securing method because a faceplate was included with the old lathe a am using. I like the spur atachment for spindle turning but think it can only be used to turn the side and bottom part of a bowl, then switch ro face plate atachment to carve out the interior. I also believe the spur securing method to be less safe to use regarding a flying bowl blank because of antention required to maintain the tail tight enough and the high torque exerted on a small diameter spur compared to a faceplate.
Thank you, the information from this video was is priceless. You were able to cover everything needed to get started turning a bowl that every new turner needs. As a new turner putting a piece on the lathe has got to be the scariest part, just not knowing if you have done it right. You didn’t push the different ways or your way is the best leaving the it up to the turner. I myself haven’t decided yet what will work for me but getting there, Slowly but surely it will come. Ideas running through my head constantly need to put them on the lathe. Again thank you for sharing it was a wonderful and enjoyable video to watch.
I will catch up on some other videos you have done. If I may ask ?
If you were turning a bowl,with epoxy what method would be the best?
I’m thinking the worm screw but still bring the tail stock up!
Thank you, Nancy. Glad you like this. Epoxy should not be any different than wood. Go with what you prefer and are comfortable using. A spur drive center, faceplate, or worm screw will all work. Happy Turning!
all 3 depending on the log blank im working with and the type of end product. face-plate and chuck is the go too for most projects.
Fantastic. Thanks and Happy Turning!
Excellent video! Just getting started. Very helpful.
Best of luck! Happy Turning!
This is an outstanding video with 1st class information! Every wood turner should watch this.
Thank you, Rex! All the best to you and Happy Turning!
Most of my bowl turnings are live edge with bark and so I drill a 2" forstner bit and expand my jaws to hold it..... I also use the forstner bit to make the bowl surface flat to accommodate the face of the chuck...But I do use the plate and screws for the larger bowls....
Sounds good!
Hi Kent, Thanks for another informative video. I’ve used all 3 methods you described, but turners who use the faceplate method on the bottoms of projects I find unsatisfactory as they leave holes in the bottom of the piece and usually way to thick of a bottom due to avoiding the screws. They could over come this by using a sacrificial glue block to attach the faceplate. I only use faceplates or woodworm screws on the future inside of the bowl and turn a tenon or recess for my 4 jaw chuck on the bottom, the the screw hole(s) are turned away. Stay safe and well to keep the videos coming. Cheers, Tom
Sounds good. Great points. Thank you and Happy Turning!
Those square headed screws are called robertsons screws. I never thought I would be teaching a master something. Love your videos , keep them coming. I always use robertsons screws.
Thanks. Good info. Is that the name of the designer of this screw? Happy Turning!
I'm reasonably new to wood turning and need to get a chuck which will help me make bowls, but i have done one just using the face plate.
Mark, yes, you can do a bowl with just a faceplate. As a matter of fact, I'll do a video on that. Stay tuned. Happy Turning!
Enjoyed the video and tutorial. Your no nonsense right at it is refreshing as some tutorials spend 1/2 the video about their dog cat or favorite ice cream cone flavor... (Sarcasm~but you know what I mean)..
My rule of thumb is the bigger the swing the more secure I want the piece.
Getting a 12 pound chunk of wood in the chest off a 900 RPM spin is very dangerous so as my mentor said, "Lock it down & save your crown."
I agree. Thank you. Maybe I'll do an all dog and ice cream video. ;) (sarcasm) Ha!
Thanks for your videos, they are helpful and informative. FYI- Without intending to, you show pretty clearly how the tailstock can slide back as you tighten (even after you smacked it with the gouge). Every time you tightened, it slid back a little.
Good to know!
I have been wood turning for 4 months and your videos are very helpful I have learned a lot from you thanks
G'day kent. great vid as usual. I use whatever I think is best at the time because my learning is by watching lots of RUclips vids. however you have lots of good info to learn from so thanks.
Thank you, William. I'm so glad to help. All the best to you and Happy Turning!
I am new to bowl turning , I’ve had the pleasure of working with a fellow that’s been turning for 30+ years and he has never showed me the worm or the spur but in my own shop I have tried that on a couple other projects with success , my bowl turning it really new as I’ve only turned two bowls to date and because I was impatient I made my first bowl into a funnel and my second bowl shattered not sure of the reason the walls were 1/2 inch still and I was going slow trying to get a good feel of the gouge but I have plans for a cherry tree and it’s going to be the smaller limbs just so I can get used to handling the gouge safely. Thank you for the videos they have shown me many things that helps a person get prepared but until you put that gouge to the wood it’s just another video. Practice makes perfect
Thank you for writing and sharing Robert! We all made at least a couple funnels. All the best to you and Happy Turning!
Thanks for the video. I started off only using faceplates, but recently transitioned to a chuck/worm screw for most bowls. Depends on the piece of wood i have on hand.
Mark, sounds good. Enjoy the learning process. Happy Turning!
Wish I would have watched this video before attempting my first bowl today. I was working a piece of firewood cedar with the four spur. Well it broke apart and threw the blank. I think my mistake was not returning to tighten the tail stock.
Yes that was my first attempt and I will be back at it tomorrow. I think I will try the face plate for a bit more security... and watch a few more videos.
You can do it! And yes, the faceplate is a very secure approach. All the best to you and Happy Turning!
Thank you for the great videos! Lots of great information!
My pleasure. Glad to help. Happy Turning!
Thank you for your great explanation. I am new to turning and this helped me a lot.
Happy to help! All the best to you and Happy Turning!
I like to use the four spur chuck. I balance the blank by balancing it on the end of a hammer handle. I do this for both ends/sides of the blank. This method gives me a good approximation of where the centre of the weight is. I like the four prong chuck because the bowl, as you said, can be adjusted as I work the wood.
Right on! Happy Turning!
Thanks again Kent for an informative video. I saw a British guy using a modification of the faceplate that attached to the 4-sided chuck instead of onto the lathe directly. It seemed secure and efficient especially since he didn't have to change the 4-sided chuck when he turned the blank around to attach it to the mortise or tenon. Hope that explanation made sense. I'm a beginner and have used all three methods.The four spur is fast and flexible, but not so secure in my limited experience. So, I've gravitated to the faceplate and screw-drive methods so far because of the security.
Thank you for writing and sharing! Yes, the faceplate is a great way to go. Happy Turning!
By the way, this was a great video. Great job explaining the differences
Joe, Glad it was helpful! All the best to you and Happy Turning!
A senior member of my turning club showed the club an alignment guide that he made to aide in centering a face plate .on blank . He turned a bit of wood the diameter of the inside of the.plate about 4 inches long with a pin in center of one end . After finding center , prick a hole , insert the dowel with pin protruding and place it in the center hole , hold plate in place and set your screws , remove the dowel and bingo perfect centered blank
To increa,se ta,il stock lock levelrakge , turn a handle about 6 inches long or slightly more and tapernit , drill it out to fit the lever and tap,it in place , no need to reef on it
Thank you for writing and sharing Gary! Happy Turning!
New to wood turning…. Bought a small lathe and have been watching your videos. I’m just using the faceplate that came with the lathe and it’s not bad. Yes, it makes the bowl bottom thicker because of the screws and that’s ok for what I do.
Thank you for explaining in detail all about woodturning.
My pleasure. All the best to you and Happy Turning!
Try putting the face plate on what will become the inside of the bowl. Then the wood with the screw holes will be cut out. Check my comment on 11/11/23 about how you can make all the faceplates you want for no money once you buy a spindle tap to cut the threads for the wood faceplates.
Fantastic. Good morning from Brazil !
Bom dia para voce da America
Thanks for very effective and informative videos, especially for a first timer like me. I followed your instructions closely when using traditional bowl gouge, but probably not close enough and for this reason I encountered many catches, some were quite strong. It was initially scary, however, they thought me how to avoid them and I got better. I was not clear about when to sharpen the bowl gouge. The turned surface was quite rough. I do not know if this was because of incorrect use of the gouge or using a dull gouge (I was using a new gouge). So please provide some insight for first timer when to know it is time to sharpen the gauge. I understand, I must try to apply your instructions as closely as possible, but there is a big distance between listening to video and applying what I learn into practice. You are a very effective teacher. Thanks again.
Thanks for writing and asking this question. There's a woodturning joke that holds a large kernel of truth. "If you think you should sharpen your gouge, you should have done it 10 minutes ago." In my Tool Sharpening Online eCourse TurnAWoodBowl.com/sharp I teach that we need to closely pay attention to the feel and "attitude" of the bowl gouge right after it is sharpened. That performance diminishes slowly and many times illusively until we are struggling at the lathe. So awareness is one key aspect. Happy Turning!
2:30 you can also generally just throw it on the lathe between centers. Thats what I usually do
I use a spring center punch or an awl to prick center holes for drive and tail centers . I turned a small handle for the. Spring center punch and epoxied it on , no need to strike with hammer and it has a, hole. In my table side tools holder , I also made a brad awl with a 10 p nail a bit of ash , and ak 3
/4
"× 3/4" Piece of copper tubing vor a ferrel . I left the original cuf point from the nail mill and just give a couple twists to make center holes
Good info. I've also used a safety center (steb center).
Cool, thanks for sharing.
Good teaching. Today was my first day turning. I learned a lot, like just how to mount a chunk of wood. Toward the end of practice, my material was no longer staying on. I used the 4 spur chuck, tried tightsng as I went. Still I struggled so here I stop. After watching your video I think I may need to tighten as I go. It was fresh green wood, Monkey tree I think. Well, at least I got through mounting and bulk or bull chisel and some skew work.
Tightening as you work is critical. Also, the type of drive center is important. I use a 4-spur drive center. It has large "paddle/spurs." Some of the spindle turning centers have smaller, finer teeth and a bowl will simply spin. Hope that helps. Happy Turning! Kent
Thanks for your good video thank you very much
Kent I saw someone use a Spurred faceplate screwless it had a bunch of metal points on it maybe 6 inches screws onto the headstock. And for the life of me, i can't find it so I'm guessing it was homemade. You take your bowl find your center you then drill a pilot hole the center guide of this spur chuck is centered in the pilot hole with a guide pin. as you push the tailstock up and tighten it up it pushed the blank into the metal spurs that holds it in place No way it's going anywhere... Maybe you've seen this and maybe I'm not calling it by its right name and that's why I'm not pulling it up. And I don't recall who was using it on RUclips... Thank You.. I just got my One way coring system today so going to be having fun with it. They was out of the #3 so waiting for it to come in ... Thanx Again.
Great training thank you
Glad you enjoyed it. Happy Turning!
I know this will be greeted with scepticism by seasoned turners but I quite often use 3M outdoor carpet tape to fasten bowl blanks to a faceplate. I have found this method is plenty strong enough to turn a mortise and I have used this method many times with no failure. Yet!
Sounds interesting. Happy Turning!
gracias me a ayudado mucho. desde puerto rico whit love
Excelente. Me alegra poder ayudar. ¡Todo lo mejor para ti y Happy Turning!
Great tutorial!
Thank you!
I suggest using a caliper for screw to drill-bit measurement unless you know the explicit size of the worm screw... Great video, thanks for sharing, learned a lot from this.
==
I always try to comment on the channels I like to support. The pronunciation is morse taper, not morris taper. I enjoy your vids. Thanks
Thanks for that!
I am very much an amateur woodworker and I like the face plate method. I do the end to end at times, but for stability for amateurs like myself, face plates can't be beat.
Cool, thanks!
I have just been gifted a lathe, something that I have wanted for years. I am a complete novice but I found your video very easy to follow and will be using many more to learn how to use my lathe. Thank you so much. Any advice on what my first project should be?
Nicola
very good new beginner here really helps thnx
Scroll chuck and base plate sir, your explanation is worth watching sir, with lots of love from India
Great instruction. I’m only a novice but occasionally when I’ve used a worm screw I have had to use a spacer between the blank and the chuck due to the depth of the bowl/platter. Always surprised by how well the wood stays on with “ minimal” screw depth.
Good point about the spacer. Thanks and Happy Turning!
I typically use the worm screw because my centers dont line up well. But I have used the spur if im unsure about the positioning when getting started
Ah, yes centers misaligned can be an issue. Great point. Happy Turning!
Awesome video! You’ve been so helpful.
Although, while I agree that square drive is a vast improvement from Phillips, I am a hardcore Torx girl…. T25 for life! One of my best friends is also a square drive guy, so we have hearty debates on the subject allmost daily….
LOL, both are infinitely better than Phillips head screws and millions times better than slot screws. LOL All the best to you and Happy Turning!
Dear Kent! Meanwhile I watched a lot of turorials on woodturning and I want to thank you for mentioning all of the concerns a beginner has to deal with. Thanks secondly for your understandable English even for non-native speakers like me; that's not self-evident for Americans. One question is left however: what are impact screws? I've never heard of it in Germany. Seems as if it's a kind of square hole... Greetings, Kerstin
Kerstin, Thank you for writing and for your kind words. When using an impact driver, screws that have a square, hex, or star hole don't seem to slip. I hope that helps. Happy Turning!
I’m a new subscriber who loves the comprehensive explanation. I have turned about 500 baseball bats on a Shop Fox lathe. Just getting into bowl turning- a completely different world. I can’t trust my tail stock bc turn handle is plastic and I have to physically push it into my work which is not a problem for spindles but not safe for bowls. Additionally my slowest speed is 800 rpms. The blank you used would scare me at that speed before I could round it out. Anyone have advice on what my next lathe should be? I want to do bowls safely but continue my bat making. Thanks!
Hello and welcome! That's a lot of bats! Very impressive! Check out my Lathe Speed video and perhaps investigate a control switch system that would give you control of your lathe speed. All the best to you and Happy Turning!
Thank you very much sir
Most welcome. Happy Turning!