PVC pneumatic cylinder
HTML-код
- Опубликовано: 27 сен 2024
- Turn on the subtitles for more information.
This is a simple action compressed air cylinder. It was the first one I made, still lacking features to replace a normal cylinder, but so far it has worked perfectly well and without leaks.
The tests were done with compressed air at a pressure of only 3 bar (44 psi). These PVC pipes are rated for up to 7.3 bar (106 psi), but I don't trust PVC pipes holding such pressures.
I've been looking for this to make a diy lemon smasher. Thanks.
A Ee 2à aW w Ss w
Vou adaptar sua ideia e fazer bomba de encher pneu de bike. Parabens muito sabio!
Parabéns pelo vídeo intuitivo!!!
Parabéns pela ideia!!!
I love the "primitive techbology" style of your videos!
Gostaria de saber que tipo de válvula de acionamento e descarga que você usou
Muito bom parabéns, será que o compressor de ar direito vai dar essa pressão.
excelente vídeo parabéns, acha que seria possível trazer um com ação
dupla ?
inteligência a 1000 grau, parabéns nota 10 e ganhou o meu👍
Lindamente planejado,amigo.
incrivel ! parabens pelo capricho
I love your videos. You are a genius
Good job 👍😊
PVC is not to be used with compressed air.
Warning!: To reduce the risk of death or serious injury from an explosion, collapse or projectile hazard and to reduce the risk of
property damage from a system failure:
• Always follow the warnings and procedures provided in
this manual.
• Only use PVC/ABS/CPVC pipe and fitting for the
conveyance of fluids as defined within the applicable
ASTM standards.
• Never use PVC/ABS/CPVC pipe and fittings for the
conveyance of gasses.
Warning!:
Testing with or use of compressed air or gas in PVC / ABS
/ CPVC pipe or fittings can result in explosive failures and
cause severe injury or death.
• NEVER test with or transport/store
compressed air or gas in PVC / ABS / CPVC
pipe or fittings.
• NEVER test PVC / ABS / CPVC pipe or
fittings with compressed air or gas, or air
over water boosters.
• ONLY use PVC / ABS / CPVC pipe or
fittings for water or approved chemicals.
• Refer to warnings on PPFA’s website and
ASTM D 1785.
Retorno por mola. Parabéns.
Τέλειο το σύστημα υψηλής πίεσης.
Sucesso sempre amigo parabéns
.desejo a você toda a sorte do mundo para você nobre amigo e muitas conquistas e prosperidades sempre sucesso.
.Deixando aquele GIGA 👍🏼🤝🏼👏🏼🇧🇷
Very good job
Galera a título de informação, cuidado com o pvc em ar comprimido, pois o mesmo quando se rompe sob pressão solta lascas que podem fazer um belo estrago. Motivo de não se usar pvc em redes de ar comprimido .
pode substituir por tubos pp de ar comprimido, aqueles da cor azul...
Amei! Muito bom!
Ensina também um compressor de armazenamento de ar caseiro.
Up
Da pra fazer com motor de geladeira e extintor usado como armazenamento
@@mecanicanagaragem5371 eu sei, eu já tenho um. Mas preciso que seja algo portátil para meu projeto.
@@shayere O cilindro pode ser feito também com aqueles amortecedores usados em marcenaria em armários, tem eles com 60 -80-100 newton é só fazer um furinho em uma das extremidades que o gás vaza e ai é só soldar, com solda branca aqueles caninhos de latão de antenas telescópicas cortados pedaços de 2 cm, eu faço e funciona para pequenos projetos da ate para fazer ele dupla ação no caso com 02 furinhos nas duas extremidades.
@@robertocavalcanti1657 sim, eu sei. Isso já vou fazer kkkkkk já estava no meu projeto. O problema está sendo encontrar no cubículos que é minha cidade e também um armazenamento de ar caseiro. No caso um cilindro tb. Mas n consigo vendar.
pushing weight is easier than lifting.
i couldn't understand what language you were speaking so i had to use subs.
Parabéns pela ideia ficou top
** I AM NOT LIABLE FOR ANY ACTION THAT MAY RESULT IN THE USE OF, OR EXPERIMENTATION WITH,
THE FOLLOWING EXAMPLE**!
Using 6" PVC pipe, 28"'s long. capped solid w/PVC cement. I inserted a SCREW TYPE tire valve into one end of the assembly BEFORE cementing! I made two of these units and strapped them onto the front and back racks of my ATV. I then applied 90 PSI to both tanks and was able to float the ATV through places others could not go!!! The tanks prevent the ATV from trying to flip upside down, "from the tires pressure". when the bottom drops out from under you! Such as a river/creek crossing or just a BIG mud hole. This trick has prevented many "flips" when riding through some hurricane made mud pits!!! Have fun and make sure the cement is applied with primer first and is COMPLETELY cured before adding ANY air pressure. While using the 6" PVC, 90 PSI is all I ever used. Be safe and Please understand, When PVC explodes from air pressure, SHARP, POINTED PIECES OF HARD PLASTIC, travel faster than the speed of sound. Your neck , face, hands, torso, etc. could be punctured/severed before you even hear the BOOM!!!
Ola, eu estou procurando uma maneira de fazer um pistão para um compressor caseiro que não use aqueles aneis de borracha pois não, você teria alguma ideia?
Thanks for demonstrating the power of
Pneumatics, with simple pvc pipes 👍
Muito bom 🎉 isso é ser um bom profissional parabéns
Como é o nome desse parafuso usado como haste?
So much good technical information ji hi Krishna hi Krishna
Olá grande inventor.
Poderia fazer um vídeo com 4 peças dessa funcionando com o ar no mesmo ritmo do motor a combustão ?
هل يصلح ان يكون مكبس وكم تساوي قوة الكبس
Is it possible to make the entire thing without any metal? By using only PVC and plastic.
Eu vi o vídeo todo achando que era uma bomba de encher pneu kkkk
👍🏻barato y sencillo
PARABÉNS..!!!! Genio..!!!
Show de bola,da para inventar várias coisas, valeu.
Fast working
Show de bola, muito bom.
ola. vc sabe onde posso encontrar pistoes hidraulicos, valvulas de controle e motores hidraulicos a um preço acessivel? pois estava querendo montar algo mais profissional vamos por assim dizer. Mesmo que seja de segunda mao.....
Parabéns 🎉
Amei isso, parabéns!
Boa tarde onde vc conseguiu essa mola ?
Valve use parking brake valve OHT CATERPILLAR ?
Amazing
Good 👍👍👍
Verry good creatif
Would you show which load can lift up?
Shwow muitbom só me falta o compressor
Parabéns boa ideia é dica
Muito bom . Legal
pudiera hacer uno que pueda con una presion de 120 psi,,, 50 cm de recorrido?
Was that oil you poured into the cylinder?
Qual a pressão de saída para movimentar o pistão ???
hi bro can please tell all the measurements and size of the things
BOA NOITE. SENSACIONAL. PARABÉNS
Quanta pressão aguenta um tubo de pvc tipo os de esgoto?
Cara tu e inteligente 👏👏👏
Азамат 👍 молодец 🙏
Pra que serve isso ?
What is the approximate total cost?
Good 👌 idea
Qual o propósito dessa engenhoca?
me ajuda eu quero colocar no carro tipo para fazer o carro co suspensao pneumatica
Sensacional!!!!
Pelo motivo de você ter muito conhecimento.
Queria que você fizesse um vídeo mostrando que é possível fazer um explosivo (bombinha) usando Mistura de Armstrong.
Se possível Claro 👍
Cool project. What size spring did you use?
Preciso uma bomba de sucção paea encher forminhas de chocolate com batente dosador
Amigo boa noite qual o controle de acionamento e volta do cilindro que vc usou?
Can we control stroke manually by flow controller?
Just want to ask sir.how much psi can a pvc cylinder hold?
Where is your last video?
Strike?
Deleted.
Xambioá from? Yt
@@flycatcher4928 Po
funny
is it use for factory automatic ?
Excelente para projetos, show.
Será que isso aew ainda tá vivo ??? parece bem frágil vc utiliza ele nos dias de hoje ? Valeu a pena ( $$) ?
Muito sucesso sou mais um inscrito que maguinifico
I am your first viewer can I get a heart
ok why not
OMG 😍 i don't believeing this love from india
Amigo me passa seu telefone, quer comprar uns para minha escola?
what is the screw at the end for? holding the cap on??
Para que por la presión del aire no vuele la tapa y no te saques un ojo si lo activas frente a ti
How to use 🤔🤔
Please make a pneumatic engine by using it cylinder
De onde vc tirou essa mola ?
excelente
Muito top irmão e obrigado por dividir conosco esse projeto
Já deixei o like
Que era lo del bote negro que le pusiste
muito show!!
I want this for cost
Ijin nyimak bosq❤❤❤👍👍👍👍
Ligado num compressor levanta até um carro. Quero ver levantados com bombas infláveis manuais ?
yesss 👍👍👍🙏🙏🙏
chamber a gun for .177 pellet?
Vazamento é muito grande?(
you should try making aluminum cartridges for a gun
Rivets are more acessive.
Eu estou precisando mesmo de um cilindro desse.
Caramba gostei da idade vou usar a ideia do senhor pra fazer um freio de mão USB pramim usar no meu
simulador
Acidente grave à vista!
A resistência desse material à pressão é duvidosa.
Brincadeiras assim com vasos de pressão costumam dar em acidente.
O AMIGO VC VENDE ELE PRONTO
this is not hydraulic slinder oil this is air slinder pump👍But nice👌work dude go✌od jop
The video is titled "pneumatic", which is air.
Idiot
Cylinder
Com conpressor consegue levantar um carro sera?
Eso sería hidráulica
how heavy is the iron?
probably around 45 lbs
11kgs
Que Deus abençoe
Cool
I've already blown up similar cylinders; better to build them with metal.
Is it?
Top