Ring Brothers Hinges & Cowl Induction Hood Install On My 1971 Fully Custom Restomod Chevelle
HTML-код
- Опубликовано: 6 июл 2022
- In this video we take a look at the new Ring Brothers Billet Hood Hinges and my Newly Acquired Cowl Induction Hood w/ Flapper Door. We also go ahead and install it as well.
#Ringbrothers #CowlInduction #Chevelle Авто/Мото
Grif the car is looking great. Man I'm so sorry to see your hood troubles. At least the hood hinges look great. I pray that I don't have your troubles my paint is green I couldn't hide the grinning.
Everything looking A1 MrGriffin 👍🏾👍🏾🔥🔥
Thanks fam!
That car is so sick & it ain’t even finished yet 🔥🔥🔥🔥🔥🔥
She on her way…
⁷ my friend before you mess with the hood those hinges is the biggest problem you have to adjust the hood hinges the trick to before you put any aftermarket conduction Hood take the hinges off the hood turn off the fenders Mount the new hood very carefully to see where everything's going to rub a lot of times this aftermarket hoods they're stamped wrong next time you take all the hinges out and put it carefully as a mock and then you take the hood hinges and you might have send them on one side or the other good luck my friend❤😊
Thank for the info. I ended up getting it all dialed it. It’s the hood and the hinges. Old aftermarket they don’t make anymore. Also, a have a few buddies of mine had to send back their hood hinges to Ring Brothers due to them not being manufactured correctly. So they fixed it at no cost.
Dope whip
Thank you!
Looks good I have the same hood hinges on my 72 chevelle but I can’t get the hood to come down on the back side how did you do it to drop the back of the hood down?
Thank you! You have to adjust the bottom part of the hinge (on fender). Keep moving the front up and the back down lil’ by lil’. Keep in mind it might throw off your alignment a lil’ as well just be patient. I also had to shim my fender too.
Letty is coming along and is lookingr really nice
Thank you!🙏🏾
Chevy gang
Yessir!
I had the same problem on my hood when I installed these hinges on my elco. The hood sits up high in the back close to the windshield.
Man! Such a battle, they can be adjusted tho to fit. It took me a while to figure it out.
I'm going through the same thing. On a 72 chevelle
Looks really good. Did you have any issues with the flapper valve hitting the firewall? Finally got mines lined up but it won’t go down in the rear because of the flapper valve.
Thank you! Yes! The pod vacuum port hit it at first. I had to bend it to clear. Also had to remove the center “leaf catcher” on the cowl. The pod was hitting it when good was closed.
🔥🔥🔥💪💪👍💯
🙌🏾🙌🏾🙌🏾
great video.. where did you run vacum tube to the motor?
Thank you! I ran it to the front of my throttle body.
Your buddy from HTOWN last thing do you have any ideas for different looking brake and fuel pedals
I went with Sandman Designs, but a place in Oregon called Axislowrider makes nice pieces as well, if you like billet.
Ok this is a beautiful detailed car ,but you have a functional cowl hood and it is not going to suck in cold air by your cutting away the dome !!! What were you thinking? Metal from stamping most always needs tweeking ! IMHO that hood had way to many defects and they should have replaced it.
Doesn’t matter at this point. I have forced induction now from a Procharger Supercharger. No need for the cold air from the dome. The functional flapper is just fine.
@@MrGriffin23your money is a waste
what kind and size rims are those
22/24
US MAGS Bastille
@@MrGriffin23 ty for the info deffently going to subscribe now:)
@@jesscanady All good! Appreciate that!
I have tried to comment on your video twice but it keeps disappearing 🤦🏽♂️.
This one stayed.
I see 🤣. I was saying if you decide to purchase another hood later on I would try either Dynacorn, AMD or National Parts Depot.