E-BIKE Conversion SW 900 ERROR Code 09 Troubleshooting | DIY Petz

Поделиться
HTML-код
  • Опубликовано: 3 дек 2024

Комментарии • 57

  • @massterrbarber
    @massterrbarber 2 месяца назад +1

    Don’t forget something that I have experienced was losing one of them washers the thermal washers for the screw for the misfits the matter what those thermal washers have to go back on, but I know you know this so I just wanted to say it so whoever sees this video and looks at the comments They understand that’s a very important part because if you forget to put the washer, the thermal washer for the MOS fats heat up and you can have the same situation all over again maybe even worse because the thermal washer is not even in very good job and testing great content Learned a bit here.

  • @JustinHodgins
    @JustinHodgins Год назад +4

    You know what? Great job my friend. I enjoyed this video. Until now, I thought mosfet was a band

    • @RollyPetz
      @RollyPetz  Год назад

      Thank you for your feeback Sir. Stay safe.

  • @mikehdez.9762
    @mikehdez.9762 9 месяцев назад +2

    Hello friend, I recently bought an electric bicycle, at first it set the speed well, but then it set a speed that was not, it went up to 99km/h, from one day to the next it was that, I suspect that there was a short circuit because it did not suffer No mishap with the bicycle overnight, I am not an electrical technician or similar, I am just an enthusiast, I don't know if it is the hall sensors in the engine that are blown and that is why it sends an erroneous reading on the screen that appears 99KM/h as I mentioned, that is, some mosfet like it appears in your video that has blown. The bicycle accelerates very hard without going through the speeds, it had 5 pre-established speeds, but the accelerator increases with greater force without going through any speed, as if it were only one, it advances but it shows 99Km/H as I mentioned, it is a planetary motor of fatbike 48v 1500w, the display is an M5. I hope you can give me some tips to fix it because I can't calculate the distances correctly because of this error that always indicates 99Km/h when moving forward. I also checked the motor to see if the magnet had fallen off, which they then say is out of place but it seems that that's ok. As a curious fact, when you tow it backwards or in reverse, the bicycle marks the KM/H well but when you move forward it does not mark anything, if you accelerate it it always goes up to 99KM/H... what could it be? I hope you can help me... thank you for reading me.

  • @slender1357
    @slender1357 11 месяцев назад

    For me it was a torn phase wire from the ebike motor. Thanks for the video

    • @RollyPetz
      @RollyPetz  11 месяцев назад +1

      Thanks for sharing sir. Stay safe.

  • @gaetanallard6931
    @gaetanallard6931 Год назад

    Very professional video, bravo sir 👍👏

    • @RollyPetz
      @RollyPetz  Год назад +2

      Thank you very much! Stay Safe.

  • @hamedali9290
    @hamedali9290 2 года назад +1

    Really nice
    I have some questions first, what is the flux question that you used and did you need the tin to install the circuit or just tighten the screw and are there differences between the electrical circuits because I did not find the same model, but I found the exact same shape, can you help me please please I have the same error 09 kontroller problem
    Thank you

    • @RollyPetz
      @RollyPetz  2 года назад +1

      Good day Sir Hamed, the flux is just an aid to the wetting ability of the solder for a uniform flow once the solder is placed. Upon replacing the damage one, I screw it first on to the aluminum heat sink before soldering to the board so that it won't move when soldering.
      Actually I also did not find the exact model, the one that was damage if you take a closer look on timeline 8:14, it is a AC165A Q8B but what I found was only a AC165A Q8C, but it did work, maybe the Q8B was of the lower rating while the Q8C was rated higher. What I noticed after the replacement during the test drive is that sometimes it would not provide assist and sometimes cut off the power, so I tried adjusting the P14 w/c was for current limiting of the controller from 10 and adjusted it to 15 and works perfectly fine. Hope this helps and thanks.

    • @hamedali9290
      @hamedali9290 2 года назад +1

      @@RollyPetz Thank you for your response, I have no experience at all, but I am optimistic and very pleased with your video. I hope there is a way to send pictures. I expect that I have exactly the same problem. I asked Amazon for some circuits and a test device, but unfortunately I do not have any experience to fix the fault in my bike Thank you very much for your reply

    • @RollyPetz
      @RollyPetz  2 года назад +2

      You're welcome Sir, hope you'll find solution for the fix. The worst thing is replacing and finding the same type of controller. Stay safe Sir.

  • @nicod974
    @nicod974 2 года назад +1

    Did you find out why the mosfets shorted?

    • @RollyPetz
      @RollyPetz  2 года назад +1

      Unfortunately Sir I am not an expert on this and really no idea why the mosfets shorted out or damaged. I'll try to dig deeper why did it happened. Tnx.

  • @JohanCerezo89
    @JohanCerezo89 2 месяца назад

    Sir may tanong ako, pwede bang kahit iba yung number nung MOSFET Pero parehas nang amp at volts

  • @darrengleed7001
    @darrengleed7001 Год назад +1

    Hi I watched your video and I have the same error I thought buying a new controller would fix the problem but the problem was still there. Any idea what else it could be ?

    • @darrengleed7001
      @darrengleed7001 Год назад

      It only shows error 9 when I turn the throttle

    • @RollyPetz
      @RollyPetz  Год назад

      Does it work now?

    • @darrengleed7001
      @darrengleed7001 Год назад

      No nothing I tried worked I have a new kit on its way

    • @Gary-d2p6o
      @Gary-d2p6o 4 месяца назад

      My SW 900 does the same, Error Code 09 when I throttle and motor doesn't work. Did u get urs to work?​@@darrengleed7001

  • @SeriousApache
    @SeriousApache Год назад +1

    I have error 09 only occasionally when driving, reboot usually solve it.
    What can possibly cause it?

    • @RollyPetz
      @RollyPetz  Год назад

      No idea really Sir, but I guess one of the mosfets have heating issue.

    • @SeriousApache
      @SeriousApache Год назад

      @@RollyPetz More data: sometimes it fixes itself after few seconds. And after disconnecting phase wires and connecting them back, this error doesn't appear anymore.

    • @robertmotion
      @robertmotion Год назад +1

      ​@@SeriousApache
      same error. same solution. just now, literally.
      gon change motor phase wires terminal ends from motor and controller for better fit then monitor for a few days.
      good stuff!
      /bklyn👑

  • @James-j3e8n
    @James-j3e8n Год назад +3

    Hey I have a error 09 issue on my sw900 the screen turns on and so does the battery however when I use the throttle it doesn’t drive does that mean I need a new motor aswell?

    • @elusiv3_toxiic523
      @elusiv3_toxiic523 5 месяцев назад

      Same problem bro, lmk if you have found out solution

    • @sjwickens6336
      @sjwickens6336 4 месяца назад

      Did you work it out?

  • @adamthomasmoran4780
    @adamthomasmoran4780 Год назад

    Hello, error 9 is a problem with the contrailer, but I disconnected the contrailer and the battery and the ride is just as heavy, although I could drive easily before, so the problem is in the motor wheel?

    • @RollyPetz
      @RollyPetz  Год назад +1

      Good day Sir, possibly that has something to do with the hub motor. Have you checked if the bearings are OK? Maybe it needs a little maintenance. thanks.

  • @ahmedaljaf1451
    @ahmedaljaf1451 5 месяцев назад

    Hi
    Can you make another video for people who have an allegro bike

    • @RollyPetz
      @RollyPetz  5 месяцев назад +1

      We' ll try Sir.

  • @veronepetiluna1280
    @veronepetiluna1280 2 года назад

    Good job🥰🥰🥰

  • @AbdullahRemmo
    @AbdullahRemmo 6 месяцев назад

    Error 10 , i disconnected all cables and put them back، but still not working??? Any Idea?

  • @takaogibson845
    @takaogibson845 Месяц назад

    I replaced all Mosfetts. It didn't work.

    • @RollyPetz
      @RollyPetz  Месяц назад

      I think you need to purchase a new controller Sir.

    • @takaogibson845
      @takaogibson845 Месяц назад

      @@RollyPetzYeah I went and bought new controller from Amazon. Probably need to do wiring configuration to work but see what happens. TY.

  • @marcosverdaguervendrell3088
    @marcosverdaguervendrell3088 2 года назад

    Buenas noches me marca error 11 sabes que puede ser ? Gracias

    • @RollyPetz
      @RollyPetz  2 года назад

      Good morning Sir.
      Error 11 is Communication transmitting issues. (Between controller and display), try to unplug the cable going to the display and try inserting it back firmly.
      Thanks.

  • @ptaylor81
    @ptaylor81 Год назад

    Ive got error code 10 on mine. I've checked all connections, but still get the error code. So now have no speed-o. Trying to figure out what am missing, but it's like looking for chicken teeth. Impossible. Help please bud?

  • @Mikey_Neuman
    @Mikey_Neuman Год назад

    How do I fix my09 code

    • @RollyPetz
      @RollyPetz  Год назад

      Hi Sir, what's the scenario for your error?

  • @somethinginterestingsubscr3511
    @somethinginterestingsubscr3511 2 года назад

    I have same problems please solved it

    • @RollyPetz
      @RollyPetz  2 года назад

      Good morning. If it's difficult for you to open up the controller, you may have it checked by an electronics technician and have the mosfets checked for a possible busted or burned out mosfets. Just have it replaced and try to test it out again. The worse thing is to have the controller replaced with the same specification. Thanks.

    • @kevinboyle393
      @kevinboyle393 2 года назад

      @@RollyPetz Can you give advise to what Mosfits. I’ve busted a few but can’t match the number on the Mosfit.11ON7F6 GF171 MB CHN829.The KT Controller LSW1599-3-2M 36V 15A Controller for Electric Bike 36V 250W. There no obvious reason why it’s blowing Mosfit. Changed the throttle and checked the wire and tested the battery. Would be great full if you can let me know link and Mosfit that would work on this controller

    • @RollyPetz
      @RollyPetz  2 года назад

      @@kevinboyle393 good day Sir. Base on my readings if the mosfets are busted meaning they can not handle the current load maybe you can replace it with a higher capacity mosfet. I'm not an expert on this one but just maybe it would do.
      Thanks.

    • @kevinboyle393
      @kevinboyle393 2 года назад

      @@RollyPetz Thank you for your reply. There was few problems that could have caused short, we now found the problem 9pin connector middle pin was bend touching other pin. This what was causing the Mosfit to blow. Need to replace but the only information I’ve got is above and can’t find the Mosfit CHN829 OR CHN051

    • @RollyPetz
      @RollyPetz  2 года назад

      @@kevinboyle393 Hi Sir, have you tried aliexpress or any online shop?

  • @WeillandVicenteFarias-xx9hn
    @WeillandVicenteFarias-xx9hn Год назад

    Error 006 ????

    • @RollyPetz
      @RollyPetz  Год назад

      Hi Sr, Error 06 says "Battery is under-voltage", you may check setup if the correct battery voltage is set under PO3 config and check the battery if the voltage is also correct. Tnx.

    • @juceluve1989
      @juceluve1989 5 месяцев назад

      Error 02 porfavor q significa

  • @albertopugliatti7749
    @albertopugliatti7749 Год назад

    Error 30 ??? 😥

    • @RollyPetz
      @RollyPetz  Год назад

      Hi Sir Alberto, for this type of controller, it only has 13 error codes. What type of ebike is this Sir?

  • @Minenotyours58
    @Minenotyours58 Год назад

    300 pesos is $17.44 us

  • @natalinorapacchietta5686
    @natalinorapacchietta5686 2 года назад

    Error 8 cosa vuol dire ? No. Va accelleratore segna errore 08

    • @RollyPetz
      @RollyPetz  2 года назад

      Good morning Sir Nat. Error 08 refers to "Throttle’s problem". Kindly check your cable connections for the throttle. Thanks.