How is the press part made? (CNC milling Part2)
HTML-код
- Опубликовано: 7 ноя 2020
- How is the press part made? (CNC milling Part2)
Finishing : Continuation of the first video
First video: • How is the press part ...
CNC Production: ruckbs.sk/
Machine: Three-axis machining center brand UDM-2216
CAD/CAM software: Cimatron 15
making a master mold iscar cnc machine vise bed mill high speed milling angular milling high speed metal milling harvi 3 c 42 u big forgings glock 19 trijicon rmr cut retract speed mastercam insulation routing
#cncmilling #cnc #cncfrezar 
Хобби
Try putting set screws in the holes, the machine will just run over them. You will avoid some of the damage from interrupted cuts. You will eventually mill past them into treads, or you will have to use a LH tap to spin them out. It worked for me last time I had a bunch of interrupted cuts.
60HRC !! Cooool!
Very good!!!😁
👍👍👍
on the lower positioning I would have made a notch on the sides and then closed in a vice, so I don't know if the two planes are parallel
more cnc mill videos please!
I'll try
Tohle vypadalo ze začátku na hodně drahý díl.Nekdy nezbývá než se spolehnout na cit co se řezných podmínek týká.
god the music.....just leave the sound of the machine instead
What is the make and model of this mill? It's an interesting design, haven't see anything like this stateside.
It is described in the description. UUD-2216 is a manufacturer from Korea
have you tried hitachi tools for hard milling?
We do not have these tools
Bu tip sulu malzemelerden çok kesiyorum 2344 ve 2379 gibi bence yanlış bağlama ve yanlış cam yapılmış çok takım harcamışsındır parçada paralellik sorunu var gibi geldi
Ballnose it okey to use for finishing?
Yes, it's a good cutter to finish
Could you explain, why you do hard milling dry?
These slices must not be liquid cooled!
If you add coolant when milling steel (aluminum and some SS/superalloys you can use coolant) you get a thermal shock every time the insert exits the cut.
Carbide no likey thermal shock, so you do it dry and use an air blast to clear chips.
You can use coolant on a lathe because once the tool is engaged, the insert stays a consistent temperature.
Am I misinformed, but micro carbide grain tools can hold liquid cooling shock.
@@uzkanda You're right, it definitely can, and you'd get away with it almost all the time. But when you start getting into things with super long run times, and very consistent cutting conditions like molds/dies, you'll see a definite tool life decrease when using coolant.
For Finishing In 60Rc we only use OSG’s New A Brand Duorney Endmills they don’t wear out, 18-20 hours they wear away .001-.002
I have question ,why harden the part and then do finish machine work .
To be accurate. During hardening, the material bends
tie pridavky na obrabanie po kaleni nie su moc velke?
Zo zadne strany boli až prehnane velké nevedel som ako to skrúti ale tento materiál pohlo max 0.2mm takže aj zlá skúsenosť je dobrá😁
@@CncFrezar a to kolko vlastne tam bol ten pridavok?... takze vravis, ze sa tvarilo ako 19312?... inac okolo 60HRC davam reznu rychlost pod polovicu, az k tretine oproti netepelne spracovanej oceli
@@dgk8456 Na zadnú stranu fajnových 5mm ale robil som protikus tam sa to nedalo vyhrubovať lebo by to nebolo ako upnúť tak tam bolo asi 14mm :-) ale chvalabohu žiadne diery tam išiel pokolm K10-ky ako po masle
@@CncFrezar technologa tam asi nemate, ci? vsetko si robis sam? modely vam dodavaju?... inac sikovny, ide Ti to...👍
Technolog, rozpočtár, programátor, frézar to všetko robíme my. Šéf len pripočíta materiál a vynásobí hodiny x cenou. Modely nám každá firma dodá pre ktorú robíme. Čiže vlastne kolko hodín mu poviem za tolko to musím aj spraviť
to muselo jezdit hodin :)
Hodín ako hodín ,ale tých plátkov kolko sa minulo :-)
i'm not familiar with aura tools
It is a German company maier-tools
Man, where do I even begin?
Is this your first part?
Small dia. tool for large face cutting area.
Wrong grade of carbide,not shock resistant.
Face tool extended to far.
Too much stock left on the one side of the 2 1/2 D areas.