If you like my video, give me a cup coffee. Thank you very much. Donate : www.paypal.com/paypalme/phdhung Facebook group : bit.ly/CreativeElectronic Contact: Magnetron0989821611@gmail.com Phone: 0989821611
Good.But the primary winding could be more tighter to reduce humming and there is no support for the heatsinks.Those heavy heatsinks will break the solder connection of the mosfets overtime.
This is part 3 (Part 1 here: ruclips.net/video/1eofmhzGPQI/видео.html Part 2 here: ruclips.net/video/OR18kqo4cNQ/видео.html) of the 2000W sine inverter project. in this video I will create a powerful PWM module with 5A driving current. It can easily control 30 mosfet IRF3205. Of course, my project doesn't use that much mosfet :)). I only use 16 mosfet. It works at 30Khz frequency. This module can work at 150Khz. This is an inverter using a pulse transformer, I use 2 50mm toroidal cores. Stage 1: The 12V voltage from the battery will be boosted to 350VDC with the pulse transformer. The oscillator is SG3525 Stage 2: The voltage of 350VDC will be converted to 220VAC using H bridge and EGS002. The LC filter will convert the voltage from the H-bridge to a sine 220VAC. The efficiency of this circuit is 92%. This is part 3, This video has 4 parts, I will upload the video soon.
Hi. I think the driver circuit is wrong for pc817 and I think the base should be connected to 5 volts. As for the current protector, I think it is better to use two rows of MOSFETs than to use one side. In general, I do not understand the feedback voltage and overload circuit. Of course, I just commented and the circuit is definitely not a problem.
I'll prefer using IRF(P)4468 due to it's low resistance(only 2~3 mohms when on ,that may reduce the power loss from mosfet) ,but it's more expensive and it need more powerful driver due to it's gate charge is almost 2~3 times higher than IRF3205. I'm thinking adding a common mode choke may probably reduce the influence to driving circuit (not sure is that right? although it seems like that circuit doesn't get influence) btw, the second winding looks so beautiful XD
Great video but one thing i didn't understand was why did you turn half of primary winding from right to left and the half other from left to write ? while in push pull the primary both half is in one side I hop you get the point and give me explanation
What diodes would you recommend to rectify the high frequency 200V into the 350VDC? I see the MUR810 in your diagram, that's an 8A diode, is this right?
I see a little illogicality here. The measured voltage is 348V. How does this light bulb work at such a high voltage. It seems to me like an ordinary classic light bulb. As far as I know, such light bulbs work on 220v.
Thanks you for a great video. Can you share the circuit diagram for egs002 dc to ac board diagram .the board you showed in the last min of video in the 4 part
@@smoke_stackz3168 It is not pure sine.It is square wave.In the next part 350v dc will be converted to 220v ac by full bridge with egs002 driver board.
HELLO -you can show us how to make a simple inverter (ie, less electronics) that outputs 2500 w 24 v to 220v with a large toroidal transformer. -I have a 220v transformer that outputs 24v 0v 24v Transformer 220V / 24V - 2000W - Power: 2000 VA (2.0KW) - Input voltage: 220V AC, - Output voltage: 24V ac - Output current: 84.81A, I want to use it on an electric radiator I use
If you like my video, give me a cup coffee. Thank you very much.
Donate : www.paypal.com/paypalme/phdhung
Facebook group : bit.ly/CreativeElectronic
Contact: Magnetron0989821611@gmail.com
Phone: 0989821611
Năm mới chúc a và gia đình mạnh khoẻ vạn sự như ý nhé
A cho e xin cái file mạch in đc không ạ. hoangnghia4@gmail.com
Inverter ki price WhatsApp number
Hello everyone. Thanks for watching my video, where are you from ?.
India 🇮🇳 🧡🧡🧡🧡
Russia :). Thank you.
Philippines🇵🇭😁😁
iran💚💙💜🇮🇷💜💙💚ایران 💪🇮🇷🇮🇷🇮🇷🇮🇷💪 thank you🧡🧡 Thanks for this channel🧡🧡
Malaysia 🇲🇾
درود به شما استاد بزرگ.واقعا کارتون عالیهبا قدرت ادامه بدید.سپاس از شما
دمت گرم. حال کردم با کامنت فارسیت😄
Good.But the primary winding could be more tighter to reduce humming and there is no support for the heatsinks.Those heavy heatsinks will break the solder connection of the mosfets overtime.
Yes, this is just the PCB test.
Sir you are soo intelligent 👍
Thanks bro.
PRICE KYA HAI
@@waseemlaghari2388 Rs2500
@@abulhassanqadri00 aap ki ye add youtube elawa daraz p b rakhi hai jaha chash on delevry ker k mangwai
@@waseemlaghari2388 thak he
very smart to use heatsink as transformer connection (MOS drain)
Excellent project
This is part 3 (Part 1 here: ruclips.net/video/1eofmhzGPQI/видео.html
Part 2 here: ruclips.net/video/OR18kqo4cNQ/видео.html) of the 2000W sine inverter project. in this video I will create a powerful PWM module with 5A driving current. It can easily control 30 mosfet IRF3205. Of course, my project doesn't use that much mosfet :)). I only use 16 mosfet. It works at 30Khz frequency. This module can work at 150Khz.
This is an inverter using a pulse transformer, I use 2 50mm toroidal cores.
Stage 1: The 12V voltage from the battery will be boosted to 350VDC with the pulse transformer. The oscillator is SG3525
Stage 2: The voltage of 350VDC will be converted to 220VAC using H bridge and EGS002.
The LC filter will convert the voltage from the H-bridge to a sine 220VAC.
The efficiency of this circuit is 92%. This is part 3, This video has 4 parts, I will upload the video soon.
Thank you, you make it so easy, 30 minutes and I understand how to make it 👍
:D
Very amazing
Thank bro
Bro I am confused with MOSFET .. please tell how much load Irf3205. And irf1404 can handle while used in 12v to 220v iron core transformer inverter
IRF3205 max ~ 200W. IRF1404 is more powerful . pls Find more information in the datasheet
Essa placa ficou muito bonita .. parabéns ... Vou tentar reproduzir
Verdade gostaria de fazer o mesmo.
Wow such amazing magic😂👌
Hi. I think the driver circuit is wrong for pc817 and I think the base should be connected to 5 volts. As for the current protector, I think it is better to use two rows of MOSFETs than to use one side. In general, I do not understand the feedback voltage and overload circuit. Of course, I just commented and the circuit is definitely not a problem.
Yes, in the old PCB version I got a little bit of a mistake, I have updated the new PCB.
When u updated
It's been a very long time but u not updated the PCB.
Really nice project I wish to make one but the transformer core is not available..
u can use EI core.
Very nice brother 👍👌👍
thanks bro
Like it bro nice 👍👍
Thanks bro
Lắp thêm mạch băm sin là ok đấy
ya
Профессионал своего дела! Моё почтение.
wait sine inverter, output DC?
oh yeah i watched that too xDDDD
watch the next video lol
bom vai ter a parte 4 da ponte h senoidal?
هل هذا الانفرتر بى قوه ٢٠٠٠ وات موجه نقية ؟
Hay quá ạ ♥️♥️♥️
good morning sir, your project always amazing
Where is Drain of IRF3205 mosfet is connected in the circuit ??
heatsink bro
good....
Can it be tried with other ferrite transformer types?
yes. bro.
@@PhdHung I'll try the circuit.
Good like ❤️❤️❤️❤️❤️❤️
Thank you, next video connecting to egs002?
Great work but I like to know the two wire you use to turn it on is it the micro controller is turn on the turn the mosfet on
Is square transformer can be used?
yes, ok bro, use trafo EE55 or more
Chao anh, anh có thể chia sẻ về công thức tính quấn biến áp xung được ko ạ. Cảm ơn anh
xem mấy video cũ có đó bạn.
Beautiful projects
Bro can we use this board with higher input voltage (24V or higher).What is input and output voltage range?
very good witsh frequency use
I'll prefer using IRF(P)4468 due to it's low resistance(only 2~3 mohms when on ,that may reduce the power loss from mosfet) ,but it's more expensive and it need more powerful driver due to it's gate charge is almost 2~3 times higher than IRF3205.
I'm thinking adding a common mode choke may probably reduce the influence to driving circuit (not sure is that right? although it seems like that circuit doesn't get influence)
btw, the second winding looks so beautiful XD
Yes. IRFP4668 is a good choice. this is just a test board, next I will design a PCB using mosfet TO-247
LIKE
điện trở 10ohm mà sao có vòng số 1 là màu vàng v Bác ơi
mình hết 10ohm nên dùng 4.7R
@@PhdHung lệch nhau v mà vẫn ổn. Amazing gút chóp... :D . Cảm ơn bác
Great video but one thing i didn't understand was why did you turn half of primary winding from right to left and the half other from left to write ? while in push pull the primary both half is in one side
I hop you get the point and give me explanation
Thanks for this important video
what happen for 270 vdc to 240 vac diagram?
270VDC can only create a max 190VAC.
@@PhdHung Input Voltage Not Important Output 220V 1500W Do you have a diagram
NICE VIDEO DEAR BRO
Really good
Sir, how many value of resistor between 7815 & 20k VR?
Awesome video love it
Good job 👌👌👍
2 stage pcb ?
yes. 12V > 350V and 350V > 220V
非常好的 Projects.
只是缺乏主要的 COIL 材料。
EI BOBBIN 的形狀編號，
COIL的規格SPECIFICATION.
I like to know if the H bridge design a better design for more heavier load the this design
Brother please make DC to DC converter 2000w
спасибо за видео!
is this item still available and where can i get it
Bonjour,bon travail à vous. J'aimerais avoir ce circuit et que faire pour l'avoir à ma disposition, merci pour vôtre compréhension
I don't understand what you mean, but I have shared all project files, You can download the file in the video description.
What diodes would you recommend to rectify the high frequency 200V into the 350VDC? I see the MUR810 in your diagram, that's an 8A diode, is this right?
KBPC50005 este puente de diodo te recomiendo , puedes manejar hasta 50A y 50vac a1000VAC
Nice
What is the output frequency
So you using inductor as transformer ?
Yes, another core can be used.
Good bro. 350 volts output dc or ac?
DC bro
Круто, мечтаю повторить
Что? Не проше купить ибп? Или на крайней случаи не плату от него.
@@ИванСивцов-с9ф дело не в покупке, дело в самоделке своими руками, купить всё что угодно можно
Могли бы схемачку нарисовать,а у вас может есть?
Top demais!!!
Please make a this circuit for 12-0-12 v transformer sir
why 7815? whene the supply is 12v?
At 350V-220V board I use IGBT, so I use 7815.
Squarewave or shine wave pls show on oscilloscope
I see a little illogicality here.
The measured voltage is 348V. How does this light bulb work at such a high voltage. It seems to me like an ordinary classic light bulb. As far as I know, such light bulbs work on 220v.
Yes, this is a filament bulb. even so, the 350V voltage is too big, it almost got burned :))
Dear you dont use 15 v regulator output in circuit board and digram plz clear why use it
thank you sir well good job I pray u teach me about d power drive d 3525 ic module thanks God bless you
Thanks you for a great video.
Can you share the circuit diagram for egs002 dc to ac board diagram .the board you showed in the last min of video in the 4 part
Sine Inverter ?
Sorry for asking twice, but is it true sine?
not yet
@@shoumikahmed6373 Thank you! But in can be made in next step or do you need to change parts?
@@shoumikahmed6373 i think its pure sine 12v to 350vdc and converted it to 350vdc to 220v ac
@@smoke_stackz3168 It is not pure sine.It is square wave.In the next part 350v dc will be converted to 220v ac by full bridge with egs002 driver board.
Sir plz make wireless bluetooth headphones with microphone...
No circuit diagram?
Also show all components and the schematic diagram
Feride core calculation plzz sir please video
Hello from Bulgaria. Great job! I wish you health and joy! What kind of paper do you use for printing the pcb? Thanks.
i use glossy paper,
Think they use a lazerjet printer
I'm confused transformer winding please detail information
Please watch part one, bro
Excelent
How to get 50-60 hz
mạch này đấu chung mass tất cả có sao k ạ
chắc ko sao. nhưng mình thích cách ly mass.
IRF3205 is rated at 55V and 110A. Then y u need 16 MOSFETS?
It will be cooler.
@@PhdHung cool...👍
Digram sho kreen or volteg rang
It's a pity if you submit a silent video and it doesn't find enough explanation, you understand and others don't understand
A làm giúp e 1 bộ gồm có modul PWM và pcb với ạh
لماذا لاتضع الخريطه عزيزي لكي ننفذها يجب ان تضع الخريطه والا مافي فائده من عملك
Where is 2nd PCB
Project file in video description
mosfet bahut jaldi heat kr rhsa hoga 1000watt pr hi
Inverter price
👍👍
i'm from malaysia. i would like to buy your hand product inverter. do you wanna sell to me?
I don't sell, I just share the project.
good work we cant understand this curcit
Schematic diagram pls
👍
From indonesia
Driver circuit diagram
HELLO
-you can show us how to make a simple inverter (ie, less electronics) that outputs 2500 w 24 v to 220v with a large toroidal transformer.
-I have a 220v transformer that outputs 24v 0v 24v
Transformer 220V / 24V - 2000W
- Power: 2000 VA (2.0KW)
- Input voltage: 220V AC,
- Output voltage: 24V ac
- Output current: 84.81A,
I want to use it on an electric radiator I use
ok bro, wait me
Aku pingin om
Cara membuat gimana ya om
Здравствуйте ещё раз. Это чо сериал по?
Lô bác
:D
Hi sir what's ur name
price boht zyada hai bhai
Input AC220V singel phase out put 380 ac 3phase please
Part 1/2/3/4 haha
И мени треба бар 1 кв .👑
More ko te jebe - nosi se u 3 lepe 😂😂 Vidis da radi na 350 V ! Sta ce ti to?