How to remove broken spark plug
HTML-код
- Опубликовано: 9 фев 2025
- How to remove broken spark plug
youtube channel : www.youtube.co....
Facebook: / mrtechnic8
Twitter: / mrtechnic8
If this video helped you out please don't forget to subscribe, give it a thumbs up or if you are feeling generous leaving a tip by clicking the " i " button on the top right corner of the screen. Thank you very much for your support!
Thank you for posting this! RUclips has saved me again. Thought I was going to have to remove the head. Worked exactly as the video showed. 1988 Honda Prelude. On the road within minutes for two broken plugs. Stoked!!
Thanks bhai. U saved atleast 2000 Rs. Garrage wala haramy bol raha tha k Engine block open karna padega fir welding marna padega fir open hoga. Mai tera video dekha aur 5 mins me khud usi garrage wale ka saman le k open kiya. Tnk u🙏
No intro no blah blah just actions....... salute!
Hi buddy thanks, I m from india , you & your technic saved my weaks and lots of mental pressure. I stuck in the same situation and you got me out from it in seconds 🙏🙏🙏🙏
I had already planned to completly open the bike's head, and take it to lathe machine & than I saw your video, and all the genuinity of my engine kept intact 😁😁😂😂😁😁🙏🙏🙏🙏🙏
Thank u bro helped a lot 🙏 💯
This just saved my life
What tool you are using? Please reply
Thank you so much bro it's really helpfull to me 😍100%working
Thanks po....sa vdeo kung paano ttanggalin anf na putol na sprkflg...
It's work bro, thank you
Welcome 👍
Thanks for the amazing trick it works 100% 🙂
Osm super bro it works and the broken plug opens successful 🥳🥳
Works 100%, 20% of the time...
Thack you so much for the help
Thanks thalaa mass 100% working
Very helpful bro thanks bro🤩🤩
Can you share the measurements of the screw driver? How long and wide it is.
Thx boos
It worked
Very helpful 👏👏👏👏
It's work if your spark plug is broken in normal tight condition, if it was broken after full tight, it will not work.
In my bike it was damage after full tight so I used screw extractor with drill machine (In reverse direction) and it comes out smoothly.
Worked❤❤❤❤
What tool are you using ?
It's works Super 😮
Exactly what I was afraid of happening watching this video happened....the porcelain didn’t hold and broke after me turning gently ...I’m stuck and at a lost of words at this point
What did you do to get it out?
How did you get them out
Me too
ur a saviorr
Good
Nice
Will this work on a 4 wheeler ?
Dude i got the same problem
It worked in a Polaris Ranger. I had to use a telescopic magnetic phone close up tool to pull the broken part since it was further down than the one in the video.
Thnxx
Mine just just shot off when I turn my car on😪😞 now its stuck in there I tighten it to hard and shot off what should I do😭😭😭😭
Did u get it out?
Pb blast it let it sit shake the can spray it down.. Antiseze it as well you will never have this problem an never over tighten
What is this pb blast ?..I'm new 2 riding
@@hikeemjohnson5160 pb blaster
E kong matigas kinakalawang pa makaya kaya ganyanin
How remove half broked spark plug
If you have a drill, and it’s really stuck in there, like it won’t budge, get a drill set and drill it out, try to go down 1/64th of an inch at a time, and have a file on you
mine become very tight the same reason why it snapped , what can you suggest should i just drill it until it become paper thin
@@giwtwm that’s what I did, drilled it out until it became paper thin, and used a file to get the last little bit out, better yet chase the threads with a tap afterwards or you could force a good plug with the proper threads through and chase it that way, the plug snapped right below the hex, so I had nothing to grab onto, no choice but to drill out. The proper way would probably to get a helicoil set and just completely drill it out, including the original threads and put in the insert. But my way worked fine, just make sure you check compression after and make sure there is no leak through after u mess with the threads
No use an easy out ! There are videos who suggest easy outs on RUclips watch them .. I tried this guys video on an LS1 with limited room and it’s useless … I then watched another video using an easy out I smashed a socket end on to the end and reversed thread it in … then the opposite way and it comes out easy … you won’t get a drill in to some motors no space …. And drilling it out is barbaric and takes up way too much time and effort
What's the name of the instrument bro? I am stuck in the same situation.plz help me.i will buy the instrument
Love that he liked this comment and never answered - super helpful
Square fluted ez out
Is the square body reason for grabbing the plug or can I just use a screwdriver that is round? Do I make sense?
Try it, i think you can do it..
nice cracked hands
Always
Lmao totally useless
Useless video . And a useless technic .. I struggled with this on a LS1 V8 .. very hard to get to .. using this a Philips is a bad idea .. I looked up another video .. that recommended “ easy out “ and they work … don’t use this technique it’s a waste of time
Thanks for your comments