Thank you David for showing using the bandsaw in real time. A lot of videos speed up the cuts and as a novice, your video helps me to know how fast to run the wood through.
I use a piano tuner app on my phone to set my blade tension. After a bit of trial and error, I found the perfect tension for my work, and then twanged the section of blade in the neck between the top and bottom wheels. The app showed the note "C" for my 6mm 6tpi blade, which I use for almost everything, so now tensioning new blades is a breeze. Re-tensioning after a bit of use is just as easy. Dale from Australia.
I am new to the band saw. I inherited my father’s so it’s an older one. I have it in my garage and has been sitting there for 8 years. It’s about time I learn how to use it. That’s for getting me motivated.
Dude! I just bought that same saw (first bandsaw) and have been looking for a video to show me about set up and operation for a couple days now and BAM I found it! Great video, great production quality and now I feel a lot more comfortable with my new tool. Thank you!
Awesome! I am a beginner woodworker who has really gotten interested in your channel... AND I own a band saw. So this video is perfect for me right now. Keep up the great work.
nice video and Thank you. My Grizzly bandsaw's resaw fence adjusts to make thinner resaw cuts. you should have a lock down lever and the back of the fence has a channel that the lock down slides into. My Best
This is a fantastic video. I bought a new bandsaw and it was not working well at all, I watched this video and made the adjustments and it works like a charm, thank you very much!
Great tips, one correction to mention though... Around the 12:30 mark when you talk about getting flack for how you cut thin straight pieces, that fence is equipped to handle the problem you're speaking of (not being able to lower the guide). If you pause at 14:10 you'll notice the fence in the background. See that T-slot riding on the table? That's so you can remove the fence and attatch it so the small thin top is now the short fence. Allowing you to cut thin straight veneer with WAY less blade exposed.
Thanks for the video, I had very bad drifting problems from day one I’ve tried everything that I could find on the internet, well I went to a wood show last week and was watching Alex snodgrass so I bought the carter guide kit and man I’m cutting paper thin straight sheets of hard wood, first thing I ever bought that really works
You probably know this but in case you don't, you can rotate your fence 90 degrees and use that T-nut style slot on the bottom to lock it in place. This gives you a much shorter fence for cutting small pieces. Of course, if you're just having fun you can do it any way you want! Great video as always and thanks!
Thank you! I just inherited a bandsaw. It needs some love, but now I feel educated enough to get it set up and start cutting. Thank you again for sharing you are a great teacher!!
The tip about using the sandpaper to hold the piece to the sled is great. I gave it a try and it made the job so much easier. On a side note you mentioned using a jointer to square up the front faces but I if you start with a square board and then send it through the planer between cuts on the bandsaw you can do the job with just the planer. Great videos, keep it up!
Just having some fun with a bandsaw. Thanks for the video. Love the music. Glad to see you incorporating your passion for making music into your making videos.
i bought a handheld circular to start, then a table, then a miter saw, and i finally got a nice 12 inch bandsaw! love woodworking but it costs a lot in the start ive collected sooo many tools over the last year, love the art on your bandsaw btw!
Baby Face Picciuto in this video! I needed this video BTW. I did my first band saw box last month (the mothers day heart) and it burned like crazy. I figured out after I made it that I A. Needed a new blade and B. Needed one with less teeth. You covered them both in this video, and you can let Highland Woodworking know I bought them both from them. Thanks David!
I watched with great interest your adjustment of the various guides. I too, have a Grizzly bandsaw bought new about 10 years ago and have scarcely used it. The reason being is blade drift. I was/am having a problem with that. I am going to try again and make some adjustments. By the way, I just got the saw out to mess with it and one of the drive wheels rubber belt just fell off in pieces. It had dry rotted. I have some new urethane ones coming in a couple of days. Mine is the 0457 model and it has the same resaw fence. I have picked up a couple of tips from you and DiResta and hope to get up the nerve to try and use the saw. Literally in 10 years it probably has less than 5 hours use.
Hey Dave, I have the same bandsaw and same issue trying to cut small pieces using the fence (and then having the guides too high). I solved it by simply laying a piece of 3/4 stock that's about 2" wide next to the fence and using the edge of the 3/4 stock as the fence for small pieces. That puts the fence back away from the blade and guides I can now lower the guides way down. It's not even a big deal if the 3/4 stock moves while you're cutting. Thanks for the great videos.
So glad you made this video. The part with you cutting a template from your book was exactly what i wanted to see. I suck at that curve lol. I must get a blade with less tpi such as the one u reccomend. thanks again!
Awesome video! You should clamp a thick shorter piece of MDF to your fence to create a shorter fence so that you don't need to have so much exposed blade.
Another Great Video Super Dave! One option for the exposed blade dilemma on the bandsaw; for thin pieces that I am cutting, I always use an aluminum yard stick and clamp it down for a fence. The 1/8" thickness is plenty height for a thin piece of wood. Hope it helps! Have A Super Week!.....Gus
Handy tutorial. We picked up a Clarke saw for our shop a while back. It was 'okay' but learning how to properly tune the blade, get everything squared and swapping out the stock 'general purpose' blade for a couple of Starrets, what an improvement!! Also.. "You've changed"..... :P
Just love your passion and Energy towards these videos and all your projects. I subscribed many years ago the first time I saw your videos. Even bought some of your patterns. Thanks for all the motivation. Keep up the good work my brother. The bandsaw looks bitching. Very cool.
Awsome Video!!! I miss the beard, but I am always jealous of beards. great tips. I hope the painted tools takes off as the new trend. I can't wait to see them in your new shop!
Nice video/tips. The paint job is fantastic - best looking saw on YT. If you really want to lower the guide bearings while using the fence, just clamp a 3/4 to 1" wide piece of 3/4 ply to the fence. Just like a sacrificial fence on the TS. You may not be able to get the bearings all the way down but it will cover up a lot of the exposed blade. OR.....you could just keep doing what you're doing, what ever works best for you. Keep it up - Good Stuff. Scott
A thought on the wooden Allen tool. You might be able to find a plastic knobbed bolt that you could replace the Allen screw. Then it would be a tool less adjustment if there is clearance. Thanks for the content, I'm at episode 50 of the "Make It" podcast, I started at the beginning after listening to a few and found the valuable gem it is. Keep up the great work.
First great vid, tips, and reminders. Second just a note, my Jet bandsaw guide blocks have thumb screw heads which seem to work just fine. And the rip fence I use a much smaller s4s board to allow for a lower blade guide. * Keep up the great work and sharing with us.👍
Great tips, you could just buy the appropriate "thumbscrews" to replace the socket head cap screws, They are cheap but if your even cheaper like me you could weld washer on the end of them.
Thanks for creating the video. Like your idea of painting your equipment. Love the Indians game on the TV in the background! Go Tribe and keep up the good work.
One thing I do when cutting patterns on the bandsaw or the scroll saw is to first put blue painters tape on the surface of the workpiece then glue the pattern on the tape. This lubricates the blade as its cutting and the pattern peels off nicely when done, no hassle.
My top tip: Sharp blades are used on wood, not on faces. Thank you mr snodgrass picciuto. This is useful info. Love the cover art on the bandsaw. Missing the cover art on face. ;) And i wish i had a bandsaw that would actually bandsaw better. My DeWalt DW100 isnt making the cut, well, just not that good. One day... He likes a grippy surface to hold his wood... Thanks for the thorough video!
good video. a couple of points: when using the vertical fence , why not use a thin piece of squared material to move the metal fence away from the blade guides and then lower the guides to a point closer to the blade and voila, good cuts. In addition, if you do decide to make the adjustment knobs for the guide bearings, you may end up with something shaking loose and causing a safety issue. Have you thought about replacing the set screw with a thumb screw, thereby having easy access as well as a safer set up?
Great tips! Also now we want to paint all our power tools. Also how much did dollar shave club pay for you to shave all your face hair :P Also, we're joking, looks fresh!
Also it's so cool you made all that music (was it the making it suggestions?)!! Also we made thumb screws from hex (allen) keys via 3d printing, a hack saw, and CA glue, and they work great. What else are you going to do with all those cheap ones you get with everything?
Thank you David for showing using the bandsaw in real time. A lot of videos speed up the cuts and as a novice, your video helps me to know how fast to run the wood through.
I use a piano tuner app on my phone to set my blade tension. After a bit of trial and error, I found the perfect tension for my work, and then twanged the section of blade in the neck between the top and bottom wheels. The app showed the note "C" for my 6mm 6tpi blade, which I use for almost everything, so now tensioning new blades is a breeze. Re-tensioning after a bit of use is just as easy. Dale from Australia.
I am new to the band saw. I inherited my father’s so it’s an older one. I have it in my garage and has been sitting there for 8 years. It’s about time I learn how to use it. That’s for getting me motivated.
i was so confused for a solid min wondering who was doing the video
hunter bean me too!!!
hunter bean k
i thought it was the nerd can in MIB
Dude! I just bought that same saw (first bandsaw) and have been looking for a video to show me about set up and operation for a couple days now and BAM I found it! Great video, great production quality and now I feel a lot more comfortable with my new tool. Thank you!
Awesome! I am a beginner woodworker who has really gotten interested in your channel... AND I own a band saw. So this video is perfect for me right now. Keep up the great work.
nice video and Thank you. My Grizzly bandsaw's resaw fence adjusts to make thinner resaw cuts. you should have a lock down lever and the back of the fence has a channel that the lock down slides into. My Best
This is a fantastic video. I bought a new bandsaw and it was not working well at all, I watched this video and made the adjustments and it works like a charm, thank you very much!
Great tips, one correction to mention though... Around the 12:30 mark when you talk about getting flack for how you cut thin straight pieces, that fence is equipped to handle the problem you're speaking of (not being able to lower the guide). If you pause at 14:10 you'll notice the fence in the background. See that T-slot riding on the table? That's so you can remove the fence and attatch it so the small thin top is now the short fence. Allowing you to cut thin straight veneer with WAY less blade exposed.
Thanks for the video, I had very bad drifting problems from day one I’ve tried everything that I could find on the internet, well I went to a wood show last week and was watching Alex snodgrass so I bought the carter guide kit and man I’m cutting paper thin straight sheets of hard wood, first thing I ever bought that really works
Looking good! Btw you inspired me to put a rug down in my shop, so cozy...
Let's start a trend!
KaiCrafted I have one too. So nice! But also a magnet for dust and tape.
KaiCrafted the rug tied the room together! Can't live without my rug in the shop now!
After years of woodworking I just, yes I know, bought my first bandsaw. Thanks for the video it has a lot of great info.
Just bought my first band saw...this has been a really helpful video, answered a lot of questions...thanks
NOT THE BEARD. ANYTHING BUT THE BEARDDDDD
You probably know this but in case you don't, you can rotate your fence 90 degrees and use that T-nut style slot on the bottom to lock it in place. This gives you a much shorter fence for cutting small pieces. Of course, if you're just having fun you can do it any way you want! Great video as always and thanks!
I have the same fence...rotating it 90 degrees results in a fence that is less than an inch tall. Great for thin stock.
That was going to be my comment too. Way safer than keeping that much blade exposed.
Scott A g
Thank you! I just inherited a bandsaw. It needs some love, but now I feel educated enough to get it set up and start cutting. Thank you again for sharing you are a great teacher!!
Watch Alex Snodgrass the bandsaw master
I'm a big fan of that Snodgrass video. Excellent walkthrough to tune up your bandsaw.
The tip about using the sandpaper to hold the piece to the sled is great. I gave it a try and it made the job so much easier. On a side note you mentioned using a jointer to square up the front faces but I if you start with a square board and then send it through the planer between cuts on the bandsaw you can do the job with just the planer. Great videos, keep it up!
Just having some fun with a bandsaw. Thanks for the video. Love the music. Glad to see you incorporating your passion for making music into your making videos.
i bought a handheld circular to start, then a table, then a miter saw, and i finally got a nice 12 inch bandsaw! love woodworking but it costs a lot in the start
ive collected sooo many tools over the last year, love the art on your bandsaw btw!
Thanks so much for this. I know I'll get a lot more use out of my bandsaw because of this!
Your videos have gotten much better, I like the way you are editing and producing now.
Nice video, thanks. My bandsaw arrives tomorrow via motor freight, so info was very helpful and timely.I even bought the same kind of bandsaw.
Awesome... thanks.... I’m starting to use a band saw as a hobby and your explanations help me a lot...👍👍👍
Looking super slick there man! Good tips. The bandsaw is always problematic for me, as my guide blocks seem to move on me.
Baby Face Picciuto in this video! I needed this video BTW. I did my first band saw box last month (the mothers day heart) and it burned like crazy. I figured out after I made it that I A. Needed a new blade and B. Needed one with less teeth. You covered them both in this video, and you can let Highland Woodworking know I bought them both from them. Thanks David!
Good tips video, thanks. I really like the idea of turning an old Allen wrench into knobs! Might have to do that one of these days
Very informative as always love the artwork you inspired me to get all of my tools done add a little bit of sunshine to the shop🌞
I watched with great interest your adjustment of the various guides. I too, have a Grizzly bandsaw bought new about 10 years ago and have scarcely used it. The reason being is blade drift. I was/am having a problem with that. I am going to try again and make some adjustments. By the way, I just got the saw out to mess with it and one of the drive wheels rubber belt just fell off in pieces. It had dry rotted. I have some new urethane ones coming in a couple of days. Mine is the 0457 model and it has the same resaw fence. I have picked up a couple of tips from you and DiResta and hope to get up the nerve to try and use the saw. Literally in 10 years it probably has less than 5 hours use.
Very cool idea to paint your equipment. Really jazz up the shop
Thanks so much. I appreciate your tips on the bandsaw and all your videos.
Who is this guy? Bring back David Picciuto.
Barbara Porter Is it a guy?
Paul jr St-Jacques l
this guy is fucking awesome...let him rock it.
Hey Dave, I have the same bandsaw and same issue trying to cut small pieces using the fence (and then having the guides too high). I solved it by simply laying a piece of 3/4 stock that's about 2" wide next to the fence and using the edge of the 3/4 stock as the fence for small pieces. That puts the fence back away from the blade and guides I can now lower the guides way down. It's not even a big deal if the 3/4 stock moves while you're cutting. Thanks for the great videos.
'Im no expert on the band saw but, i have this band saw box book...". You're killing me! ( I just got my book! Waiting for the band saw!!)
David, very helpful. Matt did an awesome job on Tricking out the band saw. Thank you.
So glad you made this video. The part with you cutting a template from your book was exactly what i wanted to see. I suck at that curve lol. I must get a blade with less tpi such as the one u reccomend. thanks again!
GREAT video David. Many Many tips & tricks in this vid.
Danke für deine wertvollen Tips.
Awesome video! You should clamp a thick shorter piece of MDF to your fence to create a shorter fence so that you don't need to have so much exposed blade.
That is really helpful, thanks!
having local artists paint your tools is an amazing idea. I cannot wait to see your new shop when everything is done.
Great video. I am considering purchasing a bandsaw and this was very helpful! Thank you!
Dude... I'm like freaking out over your smoothness.
Perfect! I watched Jimmy's vid last night! This is the perfect complement.
Love your work, awesome presentation.
Another Great Video Super Dave! One option for the exposed blade dilemma on the bandsaw; for thin pieces that I am cutting, I always use an aluminum yard stick and clamp it down for a fence. The 1/8" thickness is plenty height for a thin piece of wood. Hope it helps! Have A Super Week!.....Gus
Handy tutorial.
We picked up a Clarke saw for our shop a while back. It was 'okay' but learning how to properly tune the blade, get everything squared and swapping out the stock 'general purpose' blade for a couple of Starrets, what an improvement!!
Also..
"You've changed"..... :P
just purchased my first band saw, perfect timing!
Just got a bandsaw and love the intro video
What fantastic tips most helpful any more for other power tools ?
and always love your make something. Keep up the good work
No silly quip here this time. Great tips and information. Well done.
Just ordered the book. Can't wait to learn from the master of bandsaw boxes :-)
Great video David! Good info presented in an easy to follow format. Thank you.
Just love your passion and Energy towards these videos and all your projects. I subscribed many years ago the first time I saw your videos. Even bought some of your patterns. Thanks for all the motivation. Keep up the good work my brother. The bandsaw looks bitching. Very cool.
Thanks for all the great tips.
Awsome Video!!! I miss the beard, but I am always jealous of beards.
great tips. I hope the painted tools takes off as the new trend. I can't wait to see them in your new shop!
Great video Dave, really like the instructional aspect & that will help many people, the art on the bandsaw is fantastic 👍
Love the idea of custom painting all the tools. Great overview, David!
Nice video/tips. The paint job is fantastic - best looking saw on YT. If you really want to lower the guide bearings while using the fence, just clamp a 3/4 to 1" wide piece of 3/4 ply to the fence. Just like a sacrificial fence on the TS. You may not be able to get the bearings all the way down but it will cover up a lot of the exposed blade. OR.....you could just keep doing what you're doing, what ever works best for you. Keep it up - Good Stuff. Scott
A thought on the wooden Allen tool. You might be able to find a plastic knobbed bolt that you could replace the Allen screw. Then it would be a tool less adjustment if there is clearance. Thanks for the content, I'm at episode 50 of the "Make It" podcast, I started at the beginning after listening to a few and found the valuable gem it is. Keep up the great work.
Cool Art!! I now have ideas and a reason to break out the airbrush.
literally got a new bandsaw two days ago, thanks for just the tips 👌
First great vid, tips, and reminders. Second just a note, my Jet bandsaw guide blocks have thumb screw heads which seem to work just fine. And the rip fence I use a much smaller s4s board to allow for a lower blade guide. * Keep up the great work and sharing with us.👍
You have good tips here thanks !... btw, I use a magnet on my bandsaw to hold my allen key .
Great tips, you could just buy the appropriate "thumbscrews" to replace the socket head cap screws, They are cheap but if your even cheaper like me you could weld washer on the end of them.
Great tips and bandsaw looks super.
Thanks for all the info David! ....bandsaw looks awesome too.
Thanks for creating the video. Like your idea of painting your equipment. Love the Indians game on the TV in the background! Go Tribe and keep up the good work.
I do the same thing setting up my guides. I use the same blades too! But my saw has the riser kit. Awesome paint job!
Very helpful video, thanks 🙂
Thanks for sharing. Great video.
Great guest video this week. I look forward to seeing David next time.
awesome idea to paint all your tools in the shop with art! I might have to steal that idea
+John Cobb steal away!
I have an idea for a project for your new house and a video. Use your cnc or laser cutter and make custom outlet covers out of exotic wood.
Your music is always super sick!
You Sir, have earned a "like" simply for the "My Cousin Vinnie" reference.
Damn Dave, you really did go all out for the summer shave. Rock it man.
I liked this video! Very useful tips!
great content man! who ever is editing your videos does a great job!
Man! I've learned so much from your videos! Thank you!
Hope we see this new guy on the next installment of Makers and Shakers! LOL..Thanks for the tips!
Glad I saw this video before the meetup at Kencraft on Saturday. I'm pretty sure I would not have recognized him.
+Tim Brakefield yeah, nobody is going to know who I am! See you Saturday!
Please bring that drunken wood worker beard back David! Thanks for the tips!
Great tips, definitely learned something new!
One thing I do when cutting patterns on the bandsaw or the scroll saw is to first put blue painters tape on the surface of the workpiece then glue the pattern on the tape. This lubricates the blade as its cutting and the pattern peels off nicely when done, no hassle.
another awesome video! ....looking sharp also....
keep up the amazing, motivating work brother!!
It reminds me that I did not play bowling a long time ago...Great tips, thanks!
My top tip: Sharp blades are used on wood, not on faces.
Thank you mr snodgrass picciuto. This is useful info. Love the cover art on the bandsaw. Missing the cover art on face. ;)
And i wish i had a bandsaw that would actually bandsaw better. My DeWalt DW100 isnt making the cut, well, just not that good. One day...
He likes a grippy surface to hold his wood...
Thanks for the thorough video!
Great video dude, this makes me wanna get a bandsaw. Love the Vinny Gambini clip!!
looking forward to meeting you on Saturday. Love the paint job on the band saw badass.
+Josh Dill see you Saturday! Thanks Josh!
Really good tips!
I was wondering were did the bearded man go, till I saw the comments. It's you!
Thank you!
Subscribed for the Vinny quote 😍
😁
Comment about beard removal. #jaded
Hand Tool Rescue WTF looks like a completely different person
good video. a couple of points: when using the vertical fence , why not use a thin piece of squared material to move the metal fence away from the blade guides and then lower the guides to a point closer to the blade and voila, good cuts. In addition, if you do decide to make the adjustment knobs for the guide bearings, you may end up with something shaking loose and causing a safety issue. Have you thought about replacing the set screw with a thumb screw, thereby having easy access as well as a safer set up?
I love my flat bottom things with the grippies and the things
Very interesting as always
Who was that guy. Awesome information and excellent tips.
Great tips! Also now we want to paint all our power tools. Also how much did dollar shave club pay for you to shave all your face hair :P Also, we're joking, looks fresh!
Also it's so cool you made all that music (was it the making it suggestions?)!! Also we made thumb screws from hex (allen) keys via 3d printing, a hack saw, and CA glue, and they work great. What else are you going to do with all those cheap ones you get with everything?
He's had that awesome music he made for a long time, but I hope the prompting of the Making It suggestions bring on even more!
Agreed!
I don't bother making thumbscrews out of wood. They never feel as nice as plastic ones.
Have you made some plastic ones?
If you just wanted to remove the rough surface but not make it much thinner would you still use the planner or the drum sander?
Looking good Dave! Thanks for the tips! Great content!
Who is this baby running a bandsaw, and what have you done with David Picciuto?